from

$4.68

Spark Plug Tube Seal

from

$87.99

Manufactured to meet or exceed OE requirements; Delphi Knock Sensors help maximize engine performance with all fuels; Delphi Knock Sensors prevent against engine damage from pre-ignition knocking.

Product Features:

Delphi knock sensors help maximize engine performance with all fuels
Delphi knock sensors prevent against engine damage from pre-ignition knocking
Calibrated for a wide variety of frequencies to detect shifts, and adjust to provide accurate signals to help maximize engine performance
Flat frequency response allows the same sensor to be used on different engines and the sensor responds to knock frequencies higher than the primary frequency
Ground-isolated design with two-wire shielded harness helps protect the sensor signal from electro-magnetic interference (EMI)
Self-generating piezoelectric design requires no power to the sensor

from

$41.99

Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$6.99

The Spark Plugs are the product of years of fundamental research in the combustion field. The unique patented electrode configuration of these new The spark plugs increases the amount of combustion pressure created during each power stroke of an engine, which results in a marked increase in power output, fuel economy, and reduced emissions in all gasoline engines. E3.48 is a 14mm, 0.750 reach plug with a gasket seat. It fits a wide variety of late model applications, especially import. E3.48 is widely stocked in automotive retail stores. The automotive plugs have three legs securing the Diamond FIRE electrode to the shell. This allows for excellent heat transfer, and helps to create more turbulence in the cylinder. The patented Diamond FIRE side wire is proven to increase power, reduce fuel consumption and improve hydrocarbon emissions in long-term use.

Product Features:

E3’s Diamond Fire edge to edge ground electrode provides maximum performance with increased efficiency and a faster more complete burn.
Smoother Acceleration & Idle – The faster flame initiated by the The spark plug results in a more complete burn of the ingested fuel charge. More pressure is created against the piston more fuel is put to work
Energy – Power output improved up to 6% on average in the typical operating ranges. Results will vary.
Efficiency – The “diamond shaped” side wire electrode projects the combustion spark in a way that more quickly ignites the air/fuel mixture, thereby creating a significantly faster and larger flame kernel. The result is that more fuel is put to work durin
E3’s patented Diamond Fire Technology provides a cleaner burning combustion, which translates into fuel savings and reduced engine carbon deposits
The Spark Plugs are pre-gapped at the factory and cannot be adjusted.

from

$4.79

Champion® Platinum Power¿ spark plugs deliver powerful performance. Made from exclusive Heat-Active¿ alloy, a fine-wire center electrode and V-trimmed ground electrode provides sharp spark focus.

Product Features:

Platinum Power- Premium Spark Plug. Powerful Performance.
Platinum center electrode for long life
Fine-wire center electrode for greater ignitability
V-trimmed ground electrode promotes sharper spark focus
Heat-Active┐ alloy allows electrodes to reach optimal temperature
Platinum tipped center wire resists wear and helps to maintain proper gap spec over life of the plug

from

$6.29

IDEMITSU Premium PSF is specifically engineered to meet the demanding performance requirements of Honda and Acura power steering units. This advanced technology fluid is formulated with premium quality base oils and the latest additive technologies to provide outstanding protection and performance under the most servere environmental and driving conditions.IDEMITSU Premium PSF can also be used in most Asian Original Equipment Manufacturer (OEM) power steering units that do not utilize electronic power steering technology.

Product Features:

Unique friction technology provides efficient and noise-free operation
Advanced formulation technology provides outstanding protection to the entire power steering system while delivering smooth performance under the most severe operating conditions
Superior low temperature performance for easy flow and protection against cavitation and elimination of “squawking” and “squealing”
Excellent compatibility with seals, gaskets and internal components to reduce the potential for leaks and ensures smooth performance over extended intervals
Robust anti-wear and inhibitor chemistry provides enhanced component and fluid durability and long-life

from

$187.99

NGK ignition coils are manufactured to meet or exceed OE standards for the highest durability and operational performance, so they can be installed with confidence. NGK and their family of automotive products have over 80 year’s experience and are driven by extreme dedication to innovation, performance and quality. Developed and rigorously tested in our ISO 17025 accredited test lab under the most extreme conditions, NGK’s coil designs will outperform all others – far beyond operational environments a vehicle would actually experience

Product Features:

OE QUALITY: Vacuum-sealed premium epoxy resin and thermoplastic coil housings provide superior dielectric strength, voltage insulation and durability
OPTIMAL PERFORMANCE: Precision coil windings and laminations maximize outputs, custom NGK ASIC chipset optimizes efficiency, prevents component damage
EASE OF INSTALLATION: Includes mounting hardware and necessary components required for certain applications to ensure worry-free installation
THE NGK DIFFERENCE: Featuring superior materials and design enhancements.
EXTENSIVE TESTING: NGK ignition coils must pass extreme testing during manufacturing to ensure the highest quality and durability standards are met
PRODUCT ENGINEERING: Advanced flow and stress modeling systems preemptively identify and avoid common failure points found in OE and competitor coils

from

$71.62

Direct Ignition Coil

from

$141.99

NGK ignition coils are manufactured to meet or exceed OE standards for the highest durability and operational performance, so they can be installed with confidence. NGK and their family of automotive products have over 80 year’s experience and are driven by extreme dedication to innovation, performance and quality. Developed and rigorously tested in our ISO 17025 accredited test lab under the most extreme conditions, NGK’s coil designs will outperform all others – far beyond operational environments a vehicle would actually experience

Product Features:

OE QUALITY: Vacuum-sealed premium epoxy resin and thermoplastic coil housings provide superior dielectric strength, voltage insulation and durability
OPTIMAL PERFORMANCE: Precision coil windings and laminations maximize outputs, custom NGK ASIC chipset optimizes efficiency, prevents component damage
EASE OF INSTALLATION: NGK Ignition Coils include ignition control module, premium high temperature coil boot, and jumper harnesses where required
THE NGK DIFFERENCE: Featuring superior materials and design enhancements.
EXTENSIVE TESTING: NGK ignition coils must pass extreme testing during manufacturing to ensure the highest quality and durability standards are met
PRODUCT ENGINEERING: Advanced flow and stress modeling systems preemptively identify and avoid common failure points found in OE and competitor coils

from

$25.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$248.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$369.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$34.99

Product Features:

SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
EPDM inner insulation stops power-robbing voltage leaks.
With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
Excellent interference suppression and consistent performance
Easy lock terminals for more convenient installation.
Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
Broad coverage available for most vehicles on the road today
Include grease pack to ensure easy installation and removal

from

$11.99

CARQUEST Premium coil on plug boots are engineered to restore ignition boot reliability and performance. We have OE design providing an exact direct fit for your application and the performance and durability meet or exceed OE requirements. It offers excellent heat resistance as well as maximum protection against spark loss. With durable silicone compound for resistance to high heat or abrasion.

Product Features:

Provides excellent heat resistance as well as maximum protection against spark loss.
Durable silicone compound for resistance to high heat or abrasion
Spring included with the coil boot
Design for direct compatibility
OE design provides an exact fit for your application
Multipack provides one time replace all COP for better deal

from

$70.99

NGK variable pitch resistor cables provide uniform resistance and ensure outstanding electrical conductivity in high-quality cables. Outer EPDM/silicone jacket and inner insulation contain high voltage currents for excellent dielectric strength. NGK varia

Product Features:

PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
PREMIUM ALLOY WINDING: Variable pitch winding over Ferrite magnetic alloy coating delivers ultra low resistance and excellent interference protection
CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier

from

$251.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$212.99

CARQUEST Ignition Modules are built by an ignition systems manufacturer with expertise in the entire vehicle spark system.

Product Features:

CARQUEST Ignition Modules creates and refines the timing of the engine using various sensors and readings throughout the spark system in order to create an efficiently running engine.
CARQUEST Ignition Modules use current and voltage limiting circuitry in order to prevent the ignition coil from over voltage/current. Over voltages can allow for coils to create excessive heat which can damage to the ignition module resulting in check eng
CARQUEST Ignition Modules are 100% individually tested for all product functionalities including over voltage, timing and dwell.

from

$66.65

NGK Resistor Spark Plug Wire Sets utilize a construction method known as variable pitch wire winding to create resistance to radio frequency interference. The variable pitch winding (loose/tight/loose) provides suppression throughout a very wide range by scrambling and breaking up the electrical waves radiated by the firing of the spark plugs. A ferrite magnetic layer consisting of a mixture of rubber, plastic and powdered ferrite magnetic materials, offers uniform resistance and unsurpassed conductivity. NGK wires have a lower resistance than conventional carbon core wires (8k ohm/meter versus 16k ohm/meter). This comparison is important to remember when you consider that many manufacturers recommend wires be replaced when the resistance exceeds 20k ohm/meter. This does not leave much margin for wear when the wire may only meet original standards at the very early stages of its life.

Product Features:

OE-Equivalent.
OEM style connectors for easy Installation.
Superior Firing and Fuel Savings
Outstanding Durability and Performance
Excellent Noise Suppression
Numbered for easy cylinder identification.
High quality EPDM and Silicone coverings.

from

$71.99

DENSO First Time Fit Ignition Wire Sets are identical in form fit color and performance to the factory-installed wire sets. Every part of each wire sets construction meets or exceeds OE/OES standards.

Product Features:

Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
Identical OE end caps are designed to “click” into place for easy installation and a secure fit
Strong connections – through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation

from

$41.99

Product Features:

SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
EPDM inner insulation stops power-robbing voltage leaks.
With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
Excellent interference suppression and consistent performance
Easy lock terminals for more convenient installation.
Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
Broad coverage available for most vehicles on the road today
Include grease pack to ensure easy installation and removal

from

$10.91

Prenco Coil on Plug Boots provide the best protection possible for your ignition system versus the harsh environment created by the modem day engine. Prenco Coil on Plug Boots are constructed using the finest quality materials and compounds, and produced with superior quality tooling that exactly matches the Original Equipment Boot.

Product Features:

Prenco Coil on Plug Boots are produced using precise computer designed tooling and premium quality materials/compounds that are formulated to perform in extreme temperatures.
Prenco Coil on Plug Boots are designed as a direct replacement for the OE Boot. Springs, grommets and ferrite resistors are provided for all applications where applicable.
Inspect and replace Coil on Plug Boots every 50,000 miles and/or with every spark plug change to ensure optimum engine efficiency and performance.
Replacing Coil and Plug Boots at regular intervals will prevent/correct misfires and will help to minimize further costly damage to Ignition Coils, Sensors, Catalytic Convertors, and ECUs.

from

$52.99

DENSO First Time Fit Ignition Wire Sets are identical in form fit color and performance to the factory-installed wire sets. Every part of each wire sets construction meets or exceeds OE/OES standards.

Product Features:

Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
Identical OE end caps are designed to “click” into place for easy installation and a secure fit
Strong connections – through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation

from

$155.99

NGK ultra-low resistance mag core wire sets provide outstanding performance and durability. High-temp premium silicone outer jacket and inner EPDM/silicone insulation contain high voltage currents for excellent dielectric strength. Stainless steel winding

Product Features:

PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier

from

$71.99

Product Features:

SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
EPDM inner insulation stops power-robbing voltage leaks.
With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
Excellent interference suppression and consistent performance
Easy lock terminals for more convenient installation.
Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
Broad coverage available for most vehicles on the road today
Include grease pack to ensure easy installation and removal

from

$61.99

Product Features:

SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
EPDM inner insulation stops power-robbing voltage leaks.
With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
Excellent interference suppression and consistent performance
Easy lock terminals for more convenient installation.
Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
Broad coverage available for most vehicles on the road today
Include grease pack to ensure easy installation and removal

from

$58.49

Premium Intermotor brand wire sets are designed to exactly replace the original equipment set. They feature conductors that match original equipment in material and resistance characteristics. Intermotor uses only the best in high temp jacketing and OE bo

Product Features:

Patented Hi-Gloss Clear Coat Formulation with Hi-temp Silicone Jacket. Enhances abrasion resistance while providing greater protection against severe temperatures
Enhanced Wire Core Design matched to OE type – Low ohm, Ferrite mag, Wire wound, Silicone, or Metallic. Channels maximum voltage to spark plug and enhanced RFI protection for better overall performance

from

$64.63

NGK Resistor Spark Plug Wire Sets utilize a construction method known as variable pitch wire winding to create resistance to radio frequency interference. The variable pitch winding (loose/tight/loose) provides suppression throughout a very wide range by scrambling and breaking up the electrical waves radiated by the firing of the spark plugs. A ferrite magnetic layer consisting of a mixture of rubber, plastic and powdered ferrite magnetic materials, offers uniform resistance and unsurpassed conductivity. NGK wires have a lower resistance than conventional carbon core wires (8k ohm/meter versus 16k ohm/meter). This comparison is important to remember when you consider that many manufacturers recommend wires be replaced when the resistance exceeds 20k ohm/meter. This does not leave much margin for wear when the wire may only meet original standards at the very early stages of its life.

Product Features:

OE-Equivalent.
OEM style connectors for easy Installation.
Superior Firing and Fuel Savings
Outstanding Durability and Performance
Excellent Noise Suppression
Numbered for easy cylinder identification.
High quality EPDM and Silicone coverings.

from

$8.49

NGK Coil on Plug Boots are built to stringent OEM tolerances, combining original equipment fit, design and outstanding durability. NGK Coil on Plug Boots are manufactured using only premium silicone and always include any required internal springs and ferrite resistors for superior performance and RFI noise suppression. Bridging the important link between ignition coil and spark plug, COP boots should always be replaced with NGK Coil on Plug Boots at the time as changing spark plugs to prevent ignition problems such as flashover.

Product Features:

PREMIUM GRADE SILICONE: Designed to withstand harsh environments
OEM MATCHED: Includes all required internal springs and ferrite resistors for superior performance and RFI noise suppression