from

$42.99

Product Features:

TOYOTA 8″ V6&4CLY TURBO

from

$129.78

Differential Bearing

from

$276.99

Yukon small hole yoke for ’82 and older Toyota T100 and Tacoma (with locker) with 27 spline pinion. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Toyota Tacoma and T100 with factory locking differential
27 spline

from

$274.99

T8 30spline axle ’86-00 (24.64″ – 29.08″ CUT2LTH) 4340.

Product Features:

Fits 1979-2000 Toyota 8″ and V6 rear
4340 Chromoly
30 spline
29 1/8″ long
Cut to length design fits 26.62″-29.26″ applications
106mm brake pilot

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits standard rotation Toyota 7.5″ with 4 cylinder engine
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$8.99

Product Features:

Roll pin
Fits Toyota Tacoma and T100

from

$30.99

Product Features:

Pinion gear thrust washer
Fits Toyota Tacoma and T100

from

$8.51

Axle Seal

from

$78.99

Bearing race driver for Toyota 7.5″, 8″ rear. (TOY32307). No return.

Product Features:

Bearing race driver
Fits 32307 race
All steel construction

from

$16.99

Toyota T100 & Tacoma crush sleeve. Approx 2.325″ long.

Product Features:

Crush sleeve for Toyota Tacoma and T100 without factory locker
2.235″ tall

from

$379.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. No side shims.

Product Features:

Fits reverse rotation Toyota 7.5″
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush, and silicone.

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$529.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

from

$7.99

Oil baffle for Toyota Landcruiser reverse rotation front, 8″ IFS front & TV6/Tacoma rear with factory locker.

Product Features:

Oil baffle
Fits Toyota Landcruiser reverse rotation front

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$92.99

When the thin-gauge steel corrodes on 4Runner and Tacoma truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.

Product Features:

Rear Differential Cover
Rear Differential Cover
When the thin-gauge steel corrodes on 4Runner and Tacoma truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.
Direct replacement – this weld-on differential cover directly replaces a corroded original cover on certain Toyota 4Runner and Tacoma trucks
Cost-effective repair – rather than buy a new axle, cut off the old cover and weld on this new one

from

$18.99

Product Features:

Side gear thrust washer
Fits Toyota Tacoma and T100

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$5.99

Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landrcuiser (fine spline pinion) & T100/Tacoma with factory locker. 30mm socket, M20 x 1.5 thread.

Product Features:

Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landcruiser with 30 spline pinion and Tacoma/T100 with factory locker
20mm x 1.5 thread
30mm socket

from

$63.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), pinion shim kit, marking compound and brush. No side shims.

Product Features:

Fits Toyota 7.5″ front with 4 cylinder engine
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$298.99

Product Features:

Cross pin shaft
Fits Toyota V6

from

$759.99

Differential

from

$461.99

Yukon standard open spider gear kit for Toyota T100 & Tacoma with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Toytoa Tacoma and T100 open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin spider gear thrust washers.

from

$27.99

Pinion preload shim for Toyota T100. One single shim. 0.033″ thick. Two needed. Fits against crush sleeve.

Product Features:

Fits Toyota T100 and Tacoma
0.140″ thick

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$15.99

Ring Gear bolt for Toyota T100, Tacoma & 8″ IFS front. 12mm x 1.0.

Product Features:

Ring gear bolt for Toyota T100 and Tacoma rear without factory locking differential and Toyota Clamshell front
12mm x 1.0

from

$669.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features: