1998 Jeep Grand Cherokee Performance and Racing Products

Popular 1998 Jeep Grand Cherokee Performance and Racing Products Categories

Essential Performance and Racing Products for 1998 Jeep Grand Cherokees

Omix – Engine Mount; 4.0L (Part No.17473.13)

Engine Mount; 4.0L

from

$94.99
Is your Jeep engine moving too much when you rev it up? Are there unusual noises when you accelerate? The rubber in the engine mounts takes a beating from engine torque every time you use the gas pedal. Omix-ADA offers high quality replacement engine mounts.

Product Features:
  • Left Side
  • OE Style
  • Direct Fit
See More

Omix – Timing Chain Kit; 5.9L/6.6L; 79-91 Jeep SJ (Part No.17452.08)

Timing Chain Kit; 5.9L/6.6L; 79-91 Jeep SJ

from

$87.99
Timing chains stretch over time. If left untouched, they can begin jumping teeth on the camshaft and crankshaft sprockets. This will change your timing and will do major damage to your Jeep’s engine. It is recommended that you change the timing chain.

Product Features:
  • 3 Piece Kit
  • OE Style
  • Direct Fit
See More

Omix – Sway Bar Link (Part No.18283.22)

Sway Bar Link

from

$29.99
Does your Jeep wander down the road or shift suddenly on turns? The rubber bushings in your sway bar end links may be worn out or missing. Omix-ADA offers replacement sway bar end links to keep your Jeep under control.

Product Features:
  • Steel
  • With Bushing And Insert
  • OE Style
  • Direct Fit
  • Limited 5 Year Warranty
See More

Omix – Rocker Arm; 2.5L/4.0L/4.2L; 83-06 Jeep CJ/Wrangler YJ (Part No.17408.06)

Rocker Arm; 2.5L/4.0L/4.2L; 83-06 Jeep CJ/Wrangler YJ

from

$9.29
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • Metal
  • OE Style
  • Direct Fit
See More

Omix – Front Lower Control Arm; 84-06 Jeep Models (Part No.18280.05)

Front Lower Control Arm; 84-06 Jeep Models

from

$77.99
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • Includes Bushings
  • Left Or Right Side
  • OE Style
  • Direct Fit
See More

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.7594)

Ultra Seal: Exhaust Gasket Set

from

$49.99
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:
  • Manufactured from high-temperature steel core/graphite faced exhaust material
  • Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
  • Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
  • Conforms to and seals minor surface irregularities
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
  • Anti-Stick Properties
  • Easy Removal For Disassembly
See More

Omix – Front Sway Bar Bushing; 84-01 Jeep XJ/MJ/ZJ/SJ/YJ/J-Sr (Part No.18280.15)

Front Sway Bar Bushing; 84-01 Jeep XJ/MJ/ZJ/SJ/YJ/J-Sr

from

$5.79
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • Rubber
  • OE Style
  • Direct Fit
See More

Energy Suspension – Control Arm Bushing Set (Part No.2.3104G)

Control Arm Bushing Set

from

$114.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:
  • Maintains Better Alignment While Driving
  • Full Floating and Non Binding
  • Fits Into the Remaining Stock Control Arms
See More

Accel – Rotor:Dodge Magnum V6/V8 (Part No.130328)

Rotor:Dodge Magnum V6/V8

from

$19.99
ACCEL Hi-Performance rotors offer superior protection from arc-thru and crossfire. Features hi-performance 60,000 volt alkyd compound, stress-relieved at molding to ensure stability and resist centrifugal forces at high racing RPMs.

Product Features:
  • Max stability for all RPM ranges
  • Heavy duty for maximum energy transfer
See More

Energy Suspension – Track Arm Bushing Set (Part No.2.7103G)

Track Arm Bushing Set

from

$23.99
Product Features:
  • Made from HYPER-Flex Polyurethane
See More

Accel – High-Performance Ignition Coil – Direct OE Fit (Part No.140021)

High-Performance Ignition Coil - Direct OE Fit

from

$78.99
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

Product Features:
  • 10-15% More Energy
  • Direct Plug In Replacement Direct OE Fit
  • Advanced Bobbin Technology
  • Standard Motor Products SMP Uf-198
  • MSD 8228
  • Improved Idle Quality
  • Resists Shock And Vibration
  • Resists Corrosion
See More

Energy Suspension – Coil Spring Isolator Set (Part No.2.6102R)

Coil Spring Isolator Set

from

$65.99
Made of superior Hyper-Flex material. Saves replacing again and again, lasting 3 to 10 times longer. Assemble to chassis the same way as OEM isolators and do not adversely change ride characteristics.

Product Features:
  • Made of Superior Hyper-Flex+ Material
  • Lasts from 3 to 10 Times Longer
  • Assemble to Chassis Same Way as OEM
  • Maintains Factory Ride Characteristics
  • Simple Way to Increase Vehicle Height
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1608)

Engine Valve Cover Gasket Set

from

$37.49
Product Features:
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
  • ENGINEERED TO PERFORM – Proprietary cork-rubber formulation
  • SUPERIOR SEAL – Highly conformable to accommodate for the imperfect sealing surfaces
  • EVERY PART FOR THE REPAIR – Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
  • REAL-WORLD TESTED – Parts are tested on-vehicle and validated to ensure optimal performance on the road
See More

Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)

Tie Rod Dust Boot

from

$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:
  • Easy to Install
  • Superior Material
  • Saves Your Tie Rods
  • Lasts Longer
  • Looks Great
See More

Omix – Starter Solenoid; 87-99 Jeep Wrangler (Part No.17230.07)

Starter Solenoid; 87-99 Jeep Wrangler

from

$49.99
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • Solenoid Only
  • OE Style
  • Direct Fit
See More

MagnaFlow – Street Series Cat-Back Performance Exhaust System (Part No.15859)

Street Series Cat-Back Performance Exhaust System

from

$849.99
The MagnaFlow 1999-2004 Jeep Grand Cherokee Street Series Cat-Back Performance Exhaust System brings out the personality of your 4.0L, 4.7L 1999-2004 Jeep Grand Cherokee with our signature resonant, powerful engine tone and dyno-proven performance. Thanks to its fast-flowing, mandrel bent 2.5in. main piping and 1 Straight-Through mufflers ending in a Single Straight Passenger Side Rear exit with 4in. Polished Welded-On Double Wall Angle Cut Rolled Edge tips, this Jeep Grand Cherokee exhaust kit has the performance chops to match its sporty sound and appearance. Upgrade your ride to the next level with an exhaust that has the pipes to put other Jeep Grand Cherokee’s to shame. With this system your vehicle will be producing Moderate exterior and Mild interior sound levels while leaving other cars and trucks feeling envious at every stoplight. Exhaust kit 15859 features a cat-back layout that replaces your ride’s stock exhaust components from near the catalytic converter on back. Extensive 3D scanning during development has resulted in a direct-fit design that you can easily install yourself. 15859 is produced using CNC precision robotic manufacturing techniques and is backed by MagnaFlow’s limited finish warranty and limited construction warranty.

Product Features:
  • Durable corrosion-resistant stainless steel construction
  • CNC precision robotic manufacturing techniques
  • Dyno-proven performance
See More

Omix – Piston; 2.5L/4.0L (Part No.17427.12)

Piston; 2.5L/4.0L

from

$101.99
Are you rebuilding an engine and need a fresh set of pistons? Omix-ADA offers high-quality replacement pistons from Standard to .080 thousandths over size. Wrist pins included. They will give you years of service and get you back on the road. Sold individually.

Product Features:
  • Standard
  • OE Style
  • Direct Fit
See More

MSD Ignition – Harness; Dodge/Chrysler; 98-03 (Part No.8884)

Harness; Dodge/Chrysler; 98-03

from

$72.99
This MSD to Dodge harness is designed to provide a splice free and simple installation of an MSD Ignition control to late model Dodge vehicles equipped with the coil.

Product Features:
  • Plug-In Harness w/Color Coded Wires
  • No Cutting Or Splicing
  • Quick Easy Installation
  • Provides A Direct Plug-In Installation
  • When Adding An MSD Ignition Control
See More

Accel – Tst Jeep 94-99 4.0L Ho Efi (Part No.TST16)

Tst Jeep 94-99 4.0L Ho Efi

from

$117.99
Everything you need to Super Tune Up your truck, van, or Jeep engine! The kits includes a high performance cap and rotor. A set of 8mm Extreme 9000 Spiral Core wires. This kit also includes the ACCEL classic copper core spark plugs to fire your engine up.

Product Features:
  • Complete Super Tune Kit
  • 8mm Spiral Core Wires
  • Accel Classic Core Plugs
  • High Performance Cap And Rotor
  • Reduced Emissions
See More

Competition Cams – High Energy 206/206 Hydraulic Flat Cam (Part No.20-208-2)

High Energy 206/206 Hydraulic Flat Cam

from

$436.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

Omix – Rear Diff Cover; for Dana 44; 99-04 Jeep Grand Cherokee WJ (Part No.16595.84)

Rear Diff Cover; for Dana 44; 99-04 Jeep Grand Cherokee WJ

from

$174.99
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • Steel
  • Includes Cover; Gasket; And Bolts
  • OE Style
  • Direct Fit
See More

Omix – Cylinder Head Gasket; 4.0L; 91-95 Jeep Models (Part No.17446.05)

Cylinder Head Gasket; 4.0L; 91-95 Jeep Models

from

$38.49
Is your Jeep’s cylinder head gasket leaking? Or, are you rebuilding an engine and need a fresh gasket? Omix-ADA offers high-quality replacement cylinder head gaskets that will give you years of service and get you back on the road.

Product Features:
  • Composite
  • OE Style
  • Direct Fit
See More

Omix – Fuel Pump Module Electric (Part No.17709.28)

Fuel Pump Module Electric

from

$501.99
Has your Jeep left you on the side of the road? There’s not much guessing with a fuel pump module. They either work or they don’t. Omix-ADA offers high quality fuel pump modules to get you going again.

Product Features:
  • Built To Meet Or Exceed OE Specifications
  • OE Style
  • Direct Fit
  • Limited 5 Year Warranty
See More

Omix – Front Lower Control Arm Bushing; 93-98 Jeep Grand Cherokee ZJ (Part No.18282.03)

Front Lower Control Arm Bushing; 93-98 Jeep Grand Cherokee ZJ

from

$27.99
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • Lower
  • Metal Outer Rubber Inner
  • OE Style
  • Direct Fit
See More

Omix – Alternator: 90 Amps (Part No.17225.06)

Alternator: 90 Amps

from

$305.99
Own a Jeep The toughest four letter word on wheels. Are you looking for a parts source rugged enough to match your off the beaten path sense of adventure With more than 11,000 unique part numbers from brands like Omix-ADA, Rugged Ridge, Alloy USA, Outland Automotive, ORV Suspension and Precision Gear, consider this your trail guide to the 4×4 of your dreams. A go anywhere, anytime, in any weather vehicle. Go ahead and smile, because it’s going to take a lot of courage not to be cocky when you Own a Jeep like that Omix-ADA is more than just a parts manufacturer, they’re a community of enthusiasts dedicated to producing the finest in off-road solutions. Our products have been propelling four-wheel drive vehicles down highways, back roads and over the world’s roughest terrain for about two decades. Omix’s team of engineers have developed, tested and trail ridden many of our 11,000+ products until they were perfected for you. Omix-Ada is proud to have one of the most capable Research and Development, Engineering, and Product Design teams in the automotive aftermarket. By utilizing the latest in 3D Computer Aided Design and Finite Element Analysis, and coupling these tools with our decades of market experience, we are able to develop products that give our customers the highest value parts possible.

Product Features:


    Product Features:
    • 1991-1999 Wrangler (2.5L & 4.0L), 1991-1998 Cherokee (2.5L & 4.0L), 1993-1998 Grand Cherokee (4.0L), Alternator (90 Amp)
    • Designed to meet the demands of rugged off-road adventures, ensuring reliable performance in challenging conditions.
    • Engineered with precision using advanced 3D Computer Aided Design and Finite Element Analysis for optimal durability and efficiency.
    • Backed by decades of expertise in the automotive aftermarket, delivering high-value parts tailored for Jeep enthusiasts.
See More

Omix – Front HD Replacement Coil Spring; 93-98 Jeep Grand Cherokee ZJ (Part No.18282.10)

Front HD Replacement Coil Spring; 93-98 Jeep Grand Cherokee ZJ

from

$109.99
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • No Lift
  • OE Style
  • Direct Fit
See More

Dynomax – Super Turbo Exhaust Muffler: Universal Fit, Aluminized Steel, 20" L, 2.5" In, 2.5" Out, Oval (Part No.17748)

Super Turbo Exhaust Muffler: Universal Fit, Aluminized Steel, 20" L, 2.5" In, 2.5" Out, Oval

from

$82.99
DynoMax Super Turbo performance mufflers exclusive patented flow director design channels exhaust flow and eliminates turbulence on most applications. The large internal flow tubes improve exhaust flow and reduce backpressure. Each muffler uses fiberglass matting technology to absorb unwanted interior resonance while maintaining a mellow performance tone. The ‘Pure Unadulterated POWER’ of DynoMax Super Turbo mufflers are backed by a Limited Warranty and limited Performance & Sound Guarantee.

Product Features:
  • Large internal flow tubes improve exhaust flow and reduce backpressure
  • Exclusive patented flow director design channels exhaust flow and eliminates turbulence on most applications.
  • Fiberglass matting technology to absorb unwanted interior resonance while maintaining a mellow performance tone
  • Dyno proven to flow up to 700 SCFM
See More

Flowmaster Inc. – 50 Series Muffler, 3in Offset Inlet 3in Center Outlet, 18in long, Non-Reversible, Moderate Sound (Part No.9530560)

50 Series Muffler, 3in Offset Inlet 3in Center Outlet, 18in long, Non-Reversible, Moderate Sound

from

$271.99
Designed primarily for today’s heavy duty gas and diesel trucks, this muffler will deliver improved performance, throttle response and mileage. Featuring a deeper, moderate tone with minimal resonance, it is ideal for trucks with modified engines. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Upgrade your 1998 Jeep Grand Cherokee with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1998 Jeep Grand Cherokee, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Jeep or enhancing its overall performance, Performance and Racing Products are key to keeping your Grand Cherokee functioning at its best. At Advance Auto Parts, we offer a wide selection of 87 Performance and Racing Products for the 1998 Jeep Grand Cherokee, designed to meet your needs without breaking the bank. From Performance Exhaust Product replacements to Performance Ignition Products upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1998 Jeep Grand Cherokee at great prices. Our Performance and Racing Products inventory for this model ranges from just $4.29 to $1,398.99, with an average price of $189.09. Our 87 Performance and Racing Products in stock come from 14 trusted brands, so you’re sure to find the right part for your 1998 Jeep Grand Cherokee without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1998 Jeep Grand Cherokee, we stock popular OEM and aftermarket Performance and Racing Products from top names like K&N, Omix, Accel, and more. K&N Performance and Racing Products start at just $17.99 and boast an impressive 4.8 stars average rating from customers. Omix and Accel also bring quality to the table, with Performance and Racing Products available starting at $8.29, and at an average 4.3 stars rating. With 1,203 customer reviews and counting, our 1998 Jeep Grand Cherokee Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1998 Jeep Grand Cherokee is always ready to roll. We’re committed to providing you with everything you need to keep your Grand Cherokee in top shape, all in one place. Start shopping confidently below for your 1998 Jeep Grand Cherokee!

Best-Selling Performance Exhaust Products for 1998 Jeep Grand Cherokees

Enhance the driving experience in your Jeep with 5 quality Performance Exhaust Product components, starting at $20.99.

Flowmaster Inc. – Super 44 Series Muffler, 2.25in Center Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.942447)

Super 44 Series Muffler, 2.25in Center Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound

from

$134.99
Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Flowtech – Header Gasket Set (Part No.99361FLT)

Header Gasket Set

from

$20.99
Header Gasket Set

MagnaFlow – Street Series Cat-Back Performance Exhaust System (Part No.15858)

Street Series Cat-Back Performance Exhaust System

from

$779.99
The MagnaFlow 1998 Jeep Grand Cherokee Street Series Cat-Back Performance Exhaust System brings out the personality of your 5.2L, 5.9L 1998-1998 Jeep Grand Cherokee with our signature resonant, powerful engine tone and dyno-proven performance. Thanks to its fast-flowing, mandrel bent 2.5in. main piping and 1 Straight-Through mufflers ending in a Single Straight Passenger Side Rear exit with 3.5in. Polished Welded-On Double Wall Angle Cut Rolled Edge tips, this Jeep Grand Cherokee exhaust kit has the performance chops to match its sporty sound and appearance. Upgrade your ride to the next level with an exhaust that has the pipes to put other Jeep Grand Cherokee’s to shame. With this system your vehicle will be producing Moderate exterior and Mild interior sound levels while leaving other cars and trucks feeling envious at every stoplight. Exhaust kit 15858 features a cat-back layout that replaces your ride’s stock exhaust components from near the catalytic converter on back. Extensive 3D scanning during development has resulted in a direct-fit design that you can easily install yourself. 15858 is produced using CNC precision robotic manufacturing techniques and is backed by MagnaFlow’s limited finish warranty and limited construction warranty.

Product Features:
  • Durable corrosion-resistant stainless steel construction
  • CNC precision robotic manufacturing techniques
  • Dyno-proven performance
See More

Omix – Muffler (Part No.17609.20)

Muffler

from

$219.99
Are you smelling exhaust in your Jeep? Is your exhaust getting louder? If so, your muffler may be bad. Omix-ADA offers high quality replacement mufflers to solve the problem.

Product Features:
  • Continuous Roving Fiberglass Filling
  • OE Style
  • Direct Fit
  • Limited 5 Year Warranty
See More

Omix – Tailpipe; 5.2L; 96-98 Jeep Grand Cherokee ZJ (Part No.17615.15)

Tailpipe; 5.2L; 96-98 Jeep Grand Cherokee ZJ

from

$198.99
Is your Jeep’s exhaust pipe bent or rusted out? Trying to pass your annual state Inspection or restore your Jeep back to stock? Omix-ADA offers high quality exhaust pipes, gaskets, and hangers to keep you on the road and trail.

Product Features:
  • Aluminized Steel
  • OE Style
  • Direct Fit
See More

Most Popular 1998 Jeep Grand Cherokee Performance Ignition Products

Customize your Jeep with 7 Performance Ignition Products products like Performance Coils, Performance Ignition Kits, and Performance Ignition Parts, all priced under $199.99.

Accel – Adp.Harness 98/Newer Mopar (Part No.140021AH)

Adp.Harness 98/Newer Mopar

from

$38.99
Allows you to directly plug into the ACCEL PN 140021 Super coil when being used on a 1998 to 2002 Dodge truck, or Jeep equipped with a distributor and the newer light grey Yazaki wire harness coil connector. No cutting or splicing is required.

Product Features:
  • Nice Clean Connection
  • Easy Installation
See More

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$92.99
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Accel – High-Performance Ignition Coil – Direct OE Fit (Part No.140021)

High-Performance Ignition Coil - Direct OE Fit

from

$78.99
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

Product Features:
  • 10-15% More Energy
  • Direct Plug In Replacement Direct OE Fit
  • Advanced Bobbin Technology
  • Standard Motor Products SMP Uf-198
  • MSD 8228
  • Improved Idle Quality
  • Resists Shock And Vibration
  • Resists Corrosion
See More

MSD Ignition – Harness; Dodge/Chrysler; 98-03 (Part No.8884)

Harness; Dodge/Chrysler; 98-03

from

$72.99
This MSD to Dodge harness is designed to provide a splice free and simple installation of an MSD Ignition control to late model Dodge vehicles equipped with the coil.

Product Features:
  • Plug-In Harness w/Color Coded Wires
  • No Cutting Or Splicing
  • Quick Easy Installation
  • Provides A Direct Plug-In Installation
  • When Adding An MSD Ignition Control
See More

Omix – Ignition Coil; 98-02 Jeep Wrangler TJ (Part No.17247.05)

Ignition Coil; 98-02 Jeep Wrangler TJ

from

$45.49
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • External Coil
  • OE Style
  • Direct Fit
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$33.99


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Promaster Classic Series; Ignition Coil

from

$199.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:
  • Glass Filled Polyester Case
  • Longer Spark Duration
  • Increased Performance
  • No Energy Loss Due To Arcing
  • Includes Brass Contact Terminal
See More

Top Picks for 1998 Jeep Grand Cherokee Performance Fuel Systems

Upgrade Jeep Grand Cherokees with top-quality Performance Fuel Systems parts, including 1 OEM and aftermarket selections for your 1998 model.

Omix – Fuel Pump Module Electric (Part No.17709.28)

Fuel Pump Module Electric

from

$501.99
Has your Jeep left you on the side of the road? There’s not much guessing with a fuel pump module. They either work or they don’t. Omix-ADA offers high quality fuel pump modules to get you going again.

Product Features:
  • Built To Meet Or Exceed OE Specifications
  • OE Style
  • Direct Fit
  • Limited 5 Year Warranty
See More

In-Demand Performance Engines for 1998 Jeep Grand Cherokees

Select from 30 premium Performance Engines parts for your 1998 Jeep Grand Cherokee, with prices ranging from $8.29 to $1,398.99.

Omix – Thermostat 180 Degree; 41-71 Willys/Jeep Models (Part No.17106.02)

Thermostat 180 Degree; 41-71 Willys/Jeep Models

from

$8.29
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • OE Style
  • Direct Fit
  • Steel
  • Better Flow Control
See More

Competition Cams – Xtreme Energy 212/218 Hydraulic Flat Cam and Lifter Kit (Part No.CL20-221-3)

Xtreme Energy 212/218 Hydraulic Flat Cam and Lifter Kit

from

$344.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

FEL-PRO Performance – Performance Valve Cover Gasket Set (Part No.1607)

Performance Valve Cover Gasket Set

from

$18.99
Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:
  • Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Omix – Rocker Arm; 2.5L/4.0L/4.2L; 83-06 Jeep CJ/Wrangler YJ (Part No.17408.06)

Rocker Arm; 2.5L/4.0L/4.2L; 83-06 Jeep CJ/Wrangler YJ

from

$9.29
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • Metal
  • OE Style
  • Direct Fit
See More

FEL-PRO Performance – Performance Cylinder Head Gasket (Part No.1008)

Performance Cylinder Head Gasket

from

$44.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1608)

Engine Valve Cover Gasket Set

from

$37.49
Product Features:
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
  • ENGINEERED TO PERFORM – Proprietary cork-rubber formulation
  • SUPERIOR SEAL – Highly conformable to accommodate for the imperfect sealing surfaces
  • EVERY PART FOR THE REPAIR – Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
  • REAL-WORLD TESTED – Parts are tested on-vehicle and validated to ensure optimal performance on the road
See More

Competition Cams – Magnum 230/230 Hydraulic Flat Cam (Part No.20-232-4)

Magnum 230/230 Hydraulic Flat Cam

from

$297.99
An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Product Features:
  • Best with aftermarket torque converters and 9.5:1 compression.
  • Great high RPM power.
  • Easy on valve train parts.
  • Can be used with mild ratio rocker arms and traditional performance valve springs.
See More

Competition Cams – High Energy 218/218 Hydraulic Flat Cam (Part No.20-212-2)

High Energy 218/218 Hydraulic Flat Cam

from

$257.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

Omix – Timing Chain; 4.0L; 94-06 Jeep Wrangler (Part No.17453.10)

Timing Chain; 4.0L; 94-06 Jeep Wrangler

from

$47.49
Timing chains stretch over time. If left untouched, they can begin jumping teeth on the camshaft and crankshaft sprockets. This will change your timing and will do major damage to your Jeep’s engine. It is recommended that you change the timing chain.

Product Features:
  • OE Style
  • Direct Fit
See More

Competition Cams – High Energy 206/206 Hydraulic Flat Cam K-Kit (Part No.K20-208-2)

High Energy 206/206 Hydraulic Flat Cam K-Kit

from

$1398.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

Competition Cams – High Energy 218/218 Hydraulic Flat Cam K-Kit (Part No.K20-212-2)

High Energy 218/218 Hydraulic Flat Cam K-Kit

from

$1398.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

Competition Cams – High Energy 206/206 Hydraulic Flat Cam and Lifter Kit (Part No.CL20-208-2)

High Energy 206/206 Hydraulic Flat Cam and Lifter Kit

from

$970.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

Competition Cams – XE Computer Controlled 212/218 Hydraulic Roller Cam for Chrysler Magnum (Part No.20-745-9)

XE Computer Controlled 212/218 Hydraulic Roller Cam for Chrysler Magnum

from

$787.99
XE Computer Controlled 212/218 Hydraulic Roller Cam for Chrysler Magnum

Competition Cams – XE Computer Controlled 206/212 Hydraulic Roller Cam for Chrysler Magnum (Part No.20-744-9)

XE Computer Controlled 206/212 Hydraulic Roller Cam for Chrysler Magnum

from

$787.99
XE Computer Controlled 206/212 Hydraulic Roller Cam for Chrysler Magnum

Competition Cams – XE Computer Controlled 216/224 Hydraulic Roller Cam for Chrysler Magnum (Part No.20-746-9)

XE Computer Controlled 216/224 Hydraulic Roller Cam for Chrysler Magnum

from

$787.99
XE Computer Controlled 216/224 Hydraulic Roller Cam for Chrysler Magnum

Competition Cams – CPU 210/220HRLCHRMAG (Part No.20-604-9)

CPU 210/220HRLCHRMAG

from

$591.99
CPU 210/220HRLCHRMAG

Competition Cams – CPU 199/206HRLCHRMAG (Part No.20-608-9)

CPU 199/206HRLCHRMAG

from

$591.99
CPU 199/206HRLCHRMAG

Competition Cams – Xtreme Energy 218/224 Hydraulic Flat Cam K-Kit (Part No.K20-222-3)

Xtreme Energy 218/224 Hydraulic Flat Cam K-Kit

from

$578.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Competition Cams – Mutha’ Thumpr 235/249 Hydraulic Roller Cam (Part No.20-601-9)

Mutha' Thumpr 235/249 Hydraulic Roller Cam

from

$531.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Competition Cams – High Energy 206/206 Hydraulic Flat Cam (Part No.20-208-2)

High Energy 206/206 Hydraulic Flat Cam

from

$436.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

Competition Cams – High Energy 212/212 Hydraulic Flat Cam (Part No.20-210-2)

High Energy 212/212 Hydraulic Flat Cam

from

$394.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

Competition Cams – Xtreme Energy 224/230 Hydraulic Flat Cam and Lifter Kit (Part No.CL20-223-3)

Xtreme Energy 224/230 Hydraulic Flat Cam and Lifter Kit

from

$344.99
SMALL BLOCK CHRYSLER HYDRAULIC CAM AND LIFTER KIT – Xtreme Energy: Great for street machines, largest cam for stock converter, 273-318 works best with 2000 stall.

Product Features:
  • Cam and lifter kit for Small Block Chrysler engines
  • CL-Kit includes cam, lifters, assembly lube, instructions and decals
  • HYDRAULIC – Xtreme Energy: Great for street machines, largest cam for stock converter, 273-318 works best with 2000 stall.
  • 268/280 Advertised Duration, 224/230 Duration @ .050″, .477″/.480″ Lift, 110 Lobe Separation
  • Valve spring upgrade required
See More

Competition Cams – Xtreme Energy 218/224 Hydraulic Flat Cam (Part No.20-222-3)

Xtreme Energy 218/224 Hydraulic Flat Cam

from

$327.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Competition Cams – Xtreme Energy 230/236 Hydraulic Flat Cam (Part No.20-224-4)

Xtreme Energy 230/236 Hydraulic Flat Cam

from

$297.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Most Sold 1998 Jeep Grand Cherokee Performance Oil Filters

Explore our best-selling Jeep parts for the 1998 Grand Cherokee among 2 OEM and aftermarket options starting from $17.99.

K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2004)

Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine

from

$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:
  • HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
  • VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
  • PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
  • EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
  • EASY TO REMOVE: Fast and easy Wrench-Off removal
  • HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
  • HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
See More

Omix – Oil Cap; 72-17 Jeep JK/TJ/YJ/CJ/MK/XJ/XK/WK/KJ (Part No.17403.03)

Oil Cap; 72-17 Jeep JK/TJ/YJ/CJ/MK/XJ/XK/WK/KJ

from

$37.99
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.

Product Features:
  • Plastic Top With Rubber Gasket
  • OE Style
  • Direct Fit
See More

Top-Rated Performance and Racing Products Brands For Your 1998 Jeep Grand Cherokee

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1998 Jeep Grand Cherokees. Below you’ll find some of our best rated Performance and Racing Products from K&N, Omix, and Accel, and more. Performance and Racing Products from these brands that fit a 1998 Grand Cherokee start at just $8.29 and are rated as high as 4.8 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular K&N 1998 Jeep Grand Cherokee Performance and Racing Products

When it comes to maintaining or upgrading your 1998 Jeep Grand Cherokee, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. K&N ticks all of those boxes. We offer a wide selection of K&N Performance and Racing Products, specifically designed for the 1998 Jeep Grand Cherokee. With over 2 K&N brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $17.99, with an average price of just $192.99. Plus, with over 121 customer reviews and an average rating of 4.8 stars, you can trust that our K&N Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
from $17.99
(120)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
“All good, right filter for 1973 volvo.”

Popular Omix 1998 Jeep Grand Cherokee Performance and Racing Products

Omix auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1998 Jeep Grand Cherokee owner should feel confident when installing genuine Omix parts in their vehicle. To ensure the best fit and performance for your 1998 Grand Cherokee, Advance Auto Parts carries a full inventory of 3 Omix Performance and Racing Products. Plus you will be keeping your Jeep in peak condition while saving money because prices on these Omix Performance and Racing Products range from $8.29 to $501.99, plus, with more than 9 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.
Fuel Pump Module Electric
from $501.99
(6)
Fuel Pump Module Electric
“Exact replacement so far so good”
Thermostat 180 Degree; 41-71 Willys/Jeep Models
from $8.29
(2)
Thermostat 180 Degree; 41-71 Willys/Jeep Models
“Product is great. Installing next weekend to my jeep”
Starter
from $245.99
(1)
Starter
“I purchased this particular starter because of the name omix-ada which means quality. It also comes with a 5 year warranty……..you can’t beat that!”

FAQs for 1998 Jeep Grand Cherokee Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1998 Jeep Grand Cherokees?

Out of 87 Performance and Racing Products that fit 1998 Jeep Grand Cherokees, the following parts are the top sellers:

What’s the price range for 1998 Jeep Grand Cherokee Performance and Racing Products?

Performance and Racing Product prices for the 1998 Jeep Grand Cherokee start at $4.29 and go up to $1,398.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1998 Jeep Grand Cherokee?

The average price for Performance and Racing Products for the 1998 Jeep Grand Cherokee is $189.09. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Jeep Grand Cherokee model years?

Yes, we currently carry Performance and Racing Products for 31 model years of Jeep Grand Cherokees between 1993 and 2025. Performance and Racing Products are bought most frequently for the following model years: 2021, 2020, 2019, 2018, 2017, 2016, 2015, 2014, and 2013.

What are the cheapest Performance and Racing Products for my 1998 Jeep Grand Cherokee?

The cheapest 1998 Jeep Grand Cherokee Performance and Racing Products we carry in stock are:

What are the top-rated Performance and Racing Products that fit the 1998 Jeep Grand Cherokee?

Out of 1,203 reviews by customers, our 1998 Jeep Grand Cherokee Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1998 Jeep Grand Cherokee and their top-rated products:

Can I get help with 1998 Jeep Grand Cherokee Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Jeep Performance and Racing Products and more.

What is your return policy for Jeep Grand Cherokee Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Jeep Grand Cherokee Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.