from

$164.40

Are you looking for a quality replacement part for your vehicle’s electrical system? Today’s remanufactured alternator is a complex combination of inner workings, and we completely remanufacture them to our own premium standard. All terminals are cleaned and replated. The slip rings are polished or replaced to maintain proper contact. The rectifier, diodes, rotor and bearings are performance tested or replaced for maximum output. All housings are cleaned and refinished and all stators are tested for integrity and recoated for corrosion prevention.

Product Features:

OE-Equivalent Direct Fit Application.
Fully tested to meet OE specifications.
Provides exceptional reliability.

from

$329.97

Bosch has been a major supplier of new alternators and starters to OE vehicle manufacturers since 1913. Securing OE certification requires strict adherence to stringent precision and performance criteria. These same exacting criteria are also applied in the manufacturing of all Bosch aftermarket alternators and starters. Whether 100% remanufactured or new, Bosch Premium Alternators and Starters are quality built and 100% factory tested to ensure years of reliable performance, even under the most extreme operating conditions. That’s why they are preferred by more professional installers.

Product Features:

Built to last using the highest quality materials and the most technologically advanced manufacturing processes
Remanufactured using more new parts than any other unit
100% exhaustive multipoint quality and performance testing throughout the remanufacturing process ensures optimum starting and charging performance under all operating conditions
Every unit is full-load tested to guarantee compliance with Bosch strict performance specifications
Voltage regulator 100% tested for OE voltage specifications (new on GM and Ford)
Rectifier 100 % tested (new on Ford)
Diodes 100% tested (replaced with new as required)
Rotor 100% performance-tested for maximum electrical output
100% new long life sealed bearings with special high load, high temperature grease
Stator 100% insulation and phase balance tested
Slip rings 100% new or remachined to +/- .05mm, the tightest tolerance in the industry
100% new long life self-lubricating brushes
100% new clutch pulleys
All terminals, insulators and hardware provided

from

$171.99

Bosch has been a major supplier of new alternators to Original Equipment vehicle manufacturers since 1913. Securing OE certification requires strict adherence to stringent precision and performance criteria. These same exacting criteria are also applied in the manufacturing of all Bosch aftermarket alternators. Bosch Premium Alternators are quality built and 100% factory tested to ensure years of reliable performance, even under the most extreme operating conditions.

Product Features:

Full-load tested to guarantee compliance with Bosch’s strict performance specifications
100% factory tested, units are remanufactured (not rebuilt)
Built to last – uses high quality materials and the most technologically advanced developments.

from

$432.32

Alternator

from

$222.99

Carquest Professional alternators are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new alternators are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional alternators are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new alternators are built with all new components and are 100% triple tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
All new components are utilized to ensure long service life
Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
Internal electronics are upgraded for heavy duty reliability (where applicable)
Regulators and rectifiers are 100% electronically load tested for reliable charging performance
Application-specific technical bulletins included where applicable
All units are 100% triple tested to ensure quality and performance
Technical support team staffed with ASE Certified Technicians: 1-800-228-9672
Rotors and stators are load tested and double insulated for maximum charging performance

from

$254.99

Bosch has been a major supplier of new alternators to Original Equipment vehicle manufacturers since 1913. Securing OE certification requires strict adherence to stringent precision and performance criteria. These same exacting criteria are also applied in the manufacturing of all Bosch aftermarket alternators. Bosch Premium Alternators are quality built and 100% factory tested to ensure years of reliable performance, even under the most extreme operating conditions.

Product Features:

Full-load tested to guarantee compliance with Bosch’s strict performance specifications
100% factory tested, units are remanufactured (not rebuilt)
Built to last – uses high quality materials and the most technologically advanced developments.

from

$275.99

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
Regulators and rectifiers are 100% electronically load tested for reliable charging performance
100% new OE-quality brushes and bearings are used to ensure long service life
Rotors and stators are load tested and double insulated for maximum charging performance
Slip rings are precision polished for maximum brush contact and service life
Application-specific technical bulletins included where applicable
All units are 100% triple tested to ensure quality and performance
Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

from

$240.88

Bosch has been a major supplier of new alternators and starters to OE vehicle manufacturers since 1913. Securing OE certification requires strict adherence to stringent precision and performance criteria. These same exacting criteria are also applied in the manufacturing of all Bosch aftermarket alternators and starters. Whether 100% remanufactured or new, Bosch Premium Alternators and Starters are quality built and 100% factory tested to ensure years of reliable performance, even under the most extreme operating conditions. That’s why they are preferred by more professional installers.

Product Features:

Built to last using the highest quality materials and the most technologically advanced manufacturing processes
Remanufactured using more new parts than any other unit
100% exhaustive multipoint quality and performance testing throughout the remanufacturing process ensures optimum starting and charging performance under all operating conditions
Every unit is full-load tested to guarantee compliance with Bosch strict performance specifications
Solenoid with 100% new terminal hardware, contact face and high temperature cap, are completely disassembled and computer performance tested for pull/hold strength
100% new long life self-lubricating brushes
Gear train all new bushings
Drive with 100% new bushings, springs, rollers, washers caps and high temperature lubrication
Gear train lubricated with OE-specified grease providing protection from – 4 0 ?F to +3 02 ?F
Commutator remachined to Bosch tight tolerances
Permanent magnets/field coils tested for field strength and shorts (replaced with new as required)
Armature continuity tested, gauged, straightened and shimmed
All electrical connections resoldered
All shaft splines and load bearing surfaces lubricated with OE high temperature grade

from

$143.99

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
100% remanufactured drive clutch assembly ensures lasting performance
Armatures and commutators are 100% load tested
New motor lead terminals and solenoid contacts are used to ensure maximum connectivity
Application-specific technical bulletins included where applicable
All units are 100% triple tested to ensure quality and performance
Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

from

$184.89

Starter

from

$145.99

New Starter

from

$259.99

Starters eventually wear out over time. Does your starter spin quickly without starting the engine or make a rapid clicking noise? If so, Omix-ADA offers this direct OE replacement starter to get your motor running.

Product Features:

12 Volt
OE Style
Direct Fit
Limited 5 Year Warranty

from

$172.99

Carquest Professional starters are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new starters are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional starters are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new starters are built with all new components and are 100% triple-tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
All new components are utilized to ensure long service life
Internal electronics are upgraded for heavy duty reliability (where applicable)
Armatures and commutators are 100% load tested
Application-specific technical bulletins included where applicable
All units are 100% triple tested to ensure quality and performance
Technical support team staffed with ASE Certified Technicians: 1-800-228-10379

from

$156.99

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
100% remanufactured drive clutch assembly ensures lasting performance
Armatures and commutators are 100% load tested
New motor lead terminals and solenoid contacts are used to ensure maximum connectivity
Application-specific technical bulletins included where applicable
All units are 100% triple tested to ensure quality and performance
Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

from

$85.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure confidence and product reliability, every time.

from

$83.99

This ignition lock cylinder is designed to match the fit, function and performance of the original equipment part on specified vehicles. It is engineered to help restore ignition lock function when an original cylinder is broken or worn out.

Product Features:

Direct replacement – this ignition lock cylinder matches the fit and function of the original equipment assembly on certain vehicle years, makes and models
Ideal solution – engineered to help restore and ensure the functionality of the lock cylinder
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$109.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
100% end-of-line tested to ensure confidence and product reliability, every time.

from

$67.99

Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.

Product Features:

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Easy Installation

from

$99.99

Ignition Lock Housing

from

$109.99

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

Designed to OE standards for ease of installation
Our parts are 100% tested to verify both mechanical and electrical switching performance.
Decades of industry leading research and development focused on meeting the technician’s needs
Robust design and high grade materials meet the stringent demands of today’s service professional
BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product

from

$125.99

If you need to replace an ignition lock cylinder, this Dorman OE FIX solution makes it as easy as possible. An ignition lock cylinder replacement usually requires a tedious, manual recoding process. This cylinder includes a unique coding tool that allows you to easily, instantly code the new cylinder to your existing key with just a few twists of the wrist.

Product Features:

Smarter solution – this replacement ignition lock cylinder includes an exclusive tool that codes the new cylinder to your existing key
Saves time – by avoiding a manual recoding process, reduce install time by as much as an hour
Incredibly simple – to code the new cylinder, simply insert the existing key into the tool, fully turn clockwise and then counter-clockwise, and remove
Application specific – made to replace the original cylinder on a wide range of Chrysler, Dodge, Jeep and Plymouth model years

from

$44.49

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features: