1998 Isuzu NPR Belts and Hoses
More 1998 Isuzu NPR Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1998 Isuzu NPR, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1998 Isuzu NPR Belts and Hoses
Gates – Premium Molded Coolant Hose (Part No.23096)
from
$34.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Molded Heater Hose: EPDM, Direct Fit, 1.5" Inside Diameter (Part No.22041)
from
$121.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Heat and ozone resistant cover.
- Engineered to resist electrochemical degradation – the leading cause of hose failure.
- Re-engineered materials resist vacuum collapse. This reduces the need for internal springs in many applications.
- Meets SAE 20R4 and 20R3 Type EC Class D-1 and D-2 specifications.
- Temperature Rating: -40° F to 275° F (-40° C to 135° C) in coolant hose applications.
- Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 19" Long, 1.44" Diameter (Part No.E71538)
from
$23.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 5.25" Long, .81" Diameter (Part No.A70468)
from
$16.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Bottom Cog V-Belt; 53 Inch Long, Exact Fit Premium Quality (Part No.17530)
from
$15.79
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Dayco – Double Cog V-Belt; 46.25 Inch Long, Exact Fit Premium Quality (Part No.22463)
from
$18.29
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Gates – FLEETRUNNER BELTS (Part No.9650HD)
from
$47.99
Designed for the toughest applications, FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Heavy-Duty construction resists cracking and wear
- Oil and heat resistant
- Outperforms the competition on the most troublesome drives
- Patented EPDM construction with distinct green gum back
Driveworks – Automotive V-Belt (Part No.40017)
from
$5.99
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 19" Long, 1.44" Diameter (Part No.E71568)
from
$52.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12" Long, 1.50" Diameter (Part No.B70081)
from
$24.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 19" Long, 1.44" Diameter (Part No.E72041)
from
$23.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.21794)
from
$19.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 20" Long, 1.50" Diameter (Part No.E71167)
from
$21.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.44" Diameter (Part No.C72040)
from
$17.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.28" Diameter (Part No.E72193)
from
$50.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Molded Heater Hose: EPDM, Direct Fit, 1.25" Inside Diameter (Part No.23098)
from
$47.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube; synthetic fiber knit reinforcement; heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999034A)
from
$56.99
This genuine Litens tensioner is manufactured and designed by Litens, the world’s largest manufacturer of belt tensioners. To address shortcomings and common failure points of the original tensioner, Litens has released this new and improved design. A 20% increase in tension results in less noise and belt slip. The main tensioner pivot has been greatly improved to prevent binding frequently experienced with the original part, and a high speed bearing has been implemented to provide long life and reliability.
Product Features:
See More
Product Features:
- the world’s largest manufacturer of belt tensioners. To address shortcomings and common failure points of the original tensioner
- Litens has released this new and improved design. A 20% increase in tension results in less noise and belt slip. The main tensioner pivot has been greatly improved to prevent binding frequently experienced with the original part
- and a high speed bearing has been implemented to provide long life and reliability.
- Professional Mechanics will change this tensioner in approx. 20 minutes.
- Due to the fact that belts and tensioners have similar Original Equipment “design life targets”, it is often a best practice to replace the belt tensioner when replacing a worn or broken belt. Belt removal is required to change the tensioner. Therefore, d
- Installation instructions included.
Gates – FleetRunner½ Heavy-Duty Automatic Belt Drive Tensioner (Part No.38528)
from
$179.99
Product Features:
See More
- Optimized components engineered for maximum strength and durability
- Patented design provides superior belt alignment and tension for improved drive efficiency and life
- Patented labyrinth seal prevents contamination of internal parts for maximum durability and service life
- Long-lasting steel pulleys with dust shields to protect internal bearings from contamination
- Double row bearings carry more load and last up to 3X longer than two individual bearings
- Chrome-silicone round torsion spring for less +ex-fatigue than +at-spring designs
- Patented damping mechanism provides maximum stability, reducing vibration and increasing the life of the belt, tensioner and other accessory drive components
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999366A)
from
$92.99
This Litens supplied tensioner is manufactured to original equipment specifications. Heavy duty thermoplastic pulley construction ensures long life and trouble-free performance. This tensioner meets or exceeds all original equipment fit, form, and performance characteristics. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Dayco No Slack Gold Label – Serpentine Belt Tensioner; 1 Piece, HD, Engineered To Handle Higher Torque (Part No.89425)
from
$71.99
For heavy-duty diesel engine accessory drive applications, Dayco’s HD automatic belt tensioner is designed to handle higher torque and power pulses. The heavy-duty cast aluminum body and pulley arms translate into extra strength and durability and the pat
Product Features:
See More
Product Features:
- Designed to prevent fluctuations to the tensioner body for longer service life
- Reduces the risk of noise and helps avoid housing separation
- Includes pulleys with lubricated bearings for longer lasting performance
- Heavy-duty cast aluminum body and pulley arms translate into extra strength and durability
Driveworks – Poly Rib Belt Serpentine Belt; 37.8 Long, 4 Rib Count (Part No.378K4)
from
$25.99
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Dayco – Poly Rib Belt Serpentine Belt; 37.8 Long, 4 Rib Count (Part No.5040378)
from
$38.49
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Poly Rib Belt Serpentine Belt; 39 Long, 7 Rib Count (Part No.5070390)
from
$35.49
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Gates – V-Ribbed Serpentine Belt: 39.7" Long, 7 Rib Count, Exact Fit (Part No.K070390)
from
$56.99
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.
Product Features:
See More
Product Features:
- Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
- EPDM rubber constructions resist cracking on the rib surface
- Meets or exceeds all specifications from the Original Equipment Manufacturer
- Tensioner Replacement is Recommended (if equipped)
- Unique form grinding of each individual belt assures precise dimensional control.
- Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
Dorman – Idler Pulley (Pulley only) (Part No.419-610)
from
$12.49
This accessory drive belt tensioner pulley is designed to match the fit and function of the original pulley on specified applications. Made of quality materials, it is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this accessory drive belt tensioner pulley is designed to match the fit and function of the original pulley on specified applications
- Restores functionality – reliable replacement for an original pulley that has failed due to vibration or corrosion
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 76 mm Diameter (Part No.900027A)
from
$28.99
This pulley is manufactured by Litens Automotive the inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Heavy duty thermoplastic construction for long life and trouble-free performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
Product Features:
See More
Product Features:
- Manufactured by Litens, the largest original equipment tensioner and pulley supplier in the world, to ensure proper form, fit, and performance.
- Heavy Duty Glass Reinforced Polymer Pulley for optimized dimensional control and running surface durability
- OE-spec sealed ball bearings with synthetic grease and double lip seals for long life
Gates – DriveAlign½ Belt Drive Idler/Tensioner Pulley (Part No.38006)
from
$32.99
Product Features:
See More
- Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
- Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
- OE-quality fit for virtually every domestic or import vehicle on the road today
- Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
- Premium bearings eliminate bearing noise
- Mounting hardware included for some popular applications
- Reliable operation under severe conditions
Gates – DriveAlign½ Belt Drive Idler/Tensioner Pulley (Part No.38009)
from
$25.99
Product Features:
See More
- Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
- Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
- OE-quality fit for virtually every domestic or import vehicle on the road today
- Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
- Premium bearings eliminate bearing noise
- Mounting hardware included for some popular applications
- Reliable operation under severe conditions
Popular 1998 Isuzu NPR Belts and Hoses Categories
1998 Isuzu NPR Belts and Hoses
You count on your 1998 Isuzu NPR to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 39 Belts and Hoses ranging in price from $3.99 to $193.99, you’re sure to find everything you need for your 1998 Isuzu NPR.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 5 different brands like Dayco, DriveWorks, and Gates. 1998 Isuzu NPR Belts and Hoses start as low as $3.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 67 extensive product reviews on 1998 Isuzu NPR Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Idler Pulley (Pulley only) with 3.7 stars and Automotive V-Belt, Driveworks with 5.0 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1998 Isuzu NPR below to get started!
Top-Rated Belts and Hoses Brands For Your 1998 Isuzu NPR
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1998 Isuzu NPR running right for years to come. In our inventory you’ll find brands like Dayco, DriveWorks, Gates, and even more.
Popular Dayco Belts and Hoses
You’ll find popular Dayco brand products across Serpentine and V Belts. All are waiting to get your 1998 Isuzu NPR back on the road. Some of the top-rated Dayco products in these categories are:
from
$16.99
(1)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 5.25" Long, .81" Diameter
By-Pass Hoses
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1998 Isuzu NPR, and some of our most reviewed Dayco parts include:
from
$24.99
(16)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12" Long, 1.50" Diameter
Lower Radiator Hoses
FAQs for 1998 Isuzu NPR Belts and Hoses
What are the most purchased Belts and Hoses for the 1998 Isuzu NPR?
Out of 39 Belts and Hoses for the 1998 Isuzu NPR, the most popular in our inventory are:
from
$66.99
This product is not rated
FleetRunner« Heavy-Duty Micro-V« Serpentine Drive Belt
Serpentine Belts
What are the top-rated 1998 Isuzu NPR Belts and Hoses?
Top-rated Belts and Hoses for your 1998 Isuzu NPR based on customer reviews/ratings are:
from
$12.49
(3)
Idler Pulley (Pulley only)
“I originally had a squeak that I though was the water pump, but a new sound emerged, replace 1 of the idler pulleys and still a small squeak. However,”
from
$4.29
(1)
Automotive V-Belt, Driveworks
“Horrible. I got the wrong part and their advice was to pry it on harder. I needed the 44in belt not the 42… 2in difference. They actually refused ”
