1997 GMC Jimmy Performance Engines

2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Not for mileage or emissions applications. For trucks or vans use PN(2701) instead. Not for LT1 or Chevy bowtie heads. Not for 1987 and later stock aluminum heads. Available in cast or polished.

Product Features:

• 2500 to 6500 RPM High Performance Street Engines
• Single-Plane Low-Rise Intake Good for High RPM
• Ideal for Applications with Limited Hood Clearance
• For Top-End HP and Adequate Throttle Response
• Not for Mileage or Emissions Applications
• For Trucks or Vans Use PN[2701] Instead
• Not for LT1 or Chevy Bowtie Heads
• Not for 1987 and Later Stock Aluminum Heads

Product Features:

• 3500-8000 RPM Range
• Single Plane Type-4500 Style Flange
• 6.77 in. Front Height, 6.77 in. Center Height, 6.77 in. Rear Height
• Satin Finish
• For Raised Port 23 Degree Heads

Edelbrock part No. 2701 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response. With that the Edelbrock Performer EPS intake manifold has a runner design that’s “tuned” for peak torque at 3500 rpm on a 350-inch engine making it ideal for power from off-idle to 5500 rpm. Dyno tests showed gains of 5 hp and 9 ft-lbs. of torque over the Edelbrock Performer manifold No. 2101 on a 350 Chevy. From 3000 to 4500 rpm, the power increases averaged 5+ ft-lbs. of torque for more performance where you need it most. PLEASE NOTE: Will not fit under stock Corvette hood!

Product Features:

• Maximizes Performance with Edelbrock Carburetors
• Runners Tuned to Match Square Bore Carburetor
• Maximizes Peak Torque Around 3500 RPM
• Excellent Throttle Response and Mid-Range Power
• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Prod. +5 HP and +9 ft/lbs. of Torque Over PN[2101]
• PLEASE NOTE: Will not fit under stock Corvette hood!

Utilizes late model alternator and A/C bracket mounting provisions. Has vacuum taps off Manifold runners. Uses cable bracket P/N 20-101 for GM 700R4 transmission. Extra installation hardware included.

Product Features:

• High Rise Dual Plane Design
• Holley Pro-Jection Tbi Mounting Flange
• Erg Provisions

Edelbrock part #2999 Victor Jr. 23 degree Tall intake manifold provides maximum performance for engines with standard port location, iron and aluminum cylinder heads. This versatile manifold is excellent for many applications from high-performance’s stree

Product Features:

• Race Winning Design for all Types of Competition
• Single Plane Maximizes Torque and Horsepower
• For Performance in 3500 to 7500 RPM Range
• Exit Ports Closely Match Unported GM Bowtie Heads
• Ports Match GM PN[14011058/14011034/10134392]
• Best for Classes Restricting Porting of Intakes
• Features 1 in. Taller Carb Pad than PN[2972]

Product Features:

• Non-Rotator
• 1.500 in. Outside Diameter
• 1.082 in. Inside Diameter
• 1.340 in. Coil Blind
• Set of 16

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• Complete Kit: Includes Retainers And Locks
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Includes Superior Quality Steel Retainers
• Includes 7 deg. Heat-Treated Valve Stem Locks
• Retainers and Locks Black Oxide Coated
• Non-Rotator Style: Dyno Tested and Street Proven
• Great Match to Edelbrock Camshaft Kit

Similar in performance to the Holeshot series, the Tork Master is B&M’s lowest cost torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available.

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer

Torque Converter – Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) APPLICATION: Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) The Tork Master is B&M’s lowest cost pe

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer
• Washer Between Turbine and Cover

HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.

Product Features:

• HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.
• 287/305 Advertised Duration, 235/249 Duration @ .050″, .489″/.476″ Lift, 107 Lobe Separation
• Valve spring upgrade required

HYDRAULIC – Xtreme Energy: Good for street machines, slightly rough idle, stock converter will work but best with 1800+ stall.

Product Features:

• HYDRAULIC – Xtreme Energy: Good for street machines, slightly rough idle, stock converter will work but best with 1800+ stall.
• 268/280 Advertised Duration, 224/230 Duration @ .050″, .515″/.520″ Lift, 110 Lobe Separation
• Valve spring upgrade required
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

HYDRAULIC – Xtreme Energy: Street/strip, 2800+ stall, rough idle. 9.5:1+ compression.

Product Features:

• HYDRAULIC – Xtreme Energy: Street/strip, 2800+ stall, rough idle. 9.5:1+ compression.
• 284/296 Advertised Duration, 240/246 Duration @ .050″, .574″/.578″ Lift, 110 Lobe Separation
• Valve spring upgrade required
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.

Product Features:

• HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.
• 287/304 Advertised Duration, 235/249 Duration @ .050″, .510″/.495″ Lift, 107 Lobe Separation
• Valve spring upgrade required

HYDRAULIC – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.

Product Features:

• HYDRAULIC – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.
• 280/280 Advertised Duration, 230/230 Duration @ .050″, .480″/.480″ Lift, 110 Lobe Separation
• Valve spring upgrade required

HYDRAULIC – Xtreme Energy: Very strong mid-range torque and throttle response, 2200+ stall.

Product Features:

• HYDRAULIC – Xtreme Energy: Very strong mid-range torque and throttle response, 2200+ stall.
• 274/286 Advertised Duration, 230/236 Duration @ .050″, .490″/.490″ Lift, 110 Lobe Separation
• Valve spring upgrade required
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Grade 8 Steel

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Prevents Stud Flexing
• Black Plated Finish