from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$284.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9″ with Daytona pinion support
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$78.99

8.8″ Ford 3/4″ Notched cross pin shaft (0.750″, ’85 and older). This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers.

Product Features:

Cross pin shaft
Fits Ford 8.8″
0.750″ diameter
Notched
Not compatible with Spartan Lockers or Lock Rights

from

$26.99

Pinion nut for GM 7.6″ IRS, 8.6″ IRS and some Ford 9.75″, Check threads for proper fit before before installing. 22mm x 1.5mm, Uses 32mm socket.

Product Features:

Pinion nut for GM 7.6″ IRS and 8.6″ IRS and some Ford 9.75″
22mm x 1.5 thread
32mm socket

from

$273.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Ford 9″ with LM603011 carrier races and Daytona pinion support
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, pilot bearing, thread locker, marking compound with brush and gasket.

from

$8.99

Product Features:

Trac Loc spring for Ford 8″ and 9″

from

$184.99

Product Features:

FRD 10BLT 9.0 R/P 6.00A

from

$1178.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! This unit has been approved for competition in NASCAR National & Touring series. This is a race unit designed for extreme off road use or racing. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

Fits Ford 9″ with 35 spline axles
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA
Aggressive design for racing applications only

from

$49.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$134.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 8.8″
Includes carrier bearings and races and “super” carrier shim kit

from

$209.99

Product Features:

Spider gear kit
Fits Ford 8.8″ 28 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles.
Quality materials – all components are built for reliable longevity and performance.
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$487.99

Yukon Trac Loc internals for 8″ & 9″ Ford, 31 spline, includes hub & clutches. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 9″ with Trac Loc positraction with 31 spline axles
Includes two side gears, four pinion gears, cross pin shaft, clutch hub, roll pin and spider gear thrust washers.

from

$28.99

TAPERED ROLLER BEARI

from

$34.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles.
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid.
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$101.99

Product Features:

MINI SPOOL 8.8 FORD 31SPL

from

$33.99

Product Features:

MINI INSTALL KIT FORD 9″

from

$10.99

Replacement pinion nut for Model 20 & 35, Dana 30 JK, 44 JK front, Ford 10.25″, 10.5″ & some 9.75″. 7/8-20 thread, 1 1/8 socket.

Product Features:

Pinion nut for Jeep JK front, Jeep Liberty front, Ford 9.75″, 10.25″, 10.5″ and AMC Model 20 and Model 35
7/8″ x 20 thread
1 1/8″ socket

from

$551.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$6.99

Side gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

Side gear thrust washer for Ford 8.8″
0.750″ diameter cross pin shaft applications only

from

$28.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$149.99

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features:

AXLE SHAFT 8.8 31 SPL. L.H. 33 7/32 OA LEFT

from

$4.99

Product Features:

Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

from

$1636.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$21.79

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1957-1981 Ford 10 bolt 9 inch ring gear.

Product Features: