1997 Ford E-350 Econoline Belts and Hoses
More 1997 Ford E-350 Econoline Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1997 Ford E-350 Econoline, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1997 Ford E-350 Econoline Belts and Hoses
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 76mm Dia., 30.1mm Width, 6 Grooves (Part No.89051)
from
$24.79
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – Serpentine Idler/Tensioner Pulley; Polymer, 90mm Dia., 31mm Width, Smooth (Part No.89001)
from
$20.79
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Motorcraft – HVAC HEATER PIPE (Part No.KT-161)
from
$107.99
HVAC HEATER PIPE
Dayco – Serpentine Belt Tensioner; 1 Piece, HD, Built To Outperform And Outlast OE Parts (Part No.89257)
from
$94.99
The Dayco automatic belt tensioner features Dayco’s original, patented flat spring design to provide less operating range variation. It reduces the risk of premature accessory bearing failure due to high tension and lessens the risk of belt noise and slippage – or poor performance caused by low tension. A PTFE string wound within the spring resists abrasion and dampens noise. Dayco’s tensioner is also designed with a heavy-duty cast aluminum spring case and arm, which helps resist cracking and fatigue and offers additional strength, lessening the risk of distortion. Additional premium thermoplastic rubber spring slot plugs and rubber O-ring seals help keep contaminants out and zinc coated mounting bolts resist rust.
Product Features:
See More
Product Features:
- Endures the toughest conditions while promoting quieter performance and longer life
- Features a steel pivot tube on specific designs for enhanced stability
- Built to outperform and outlast competitive OE parts
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 90mm Dia., 39.5mm Width, Smooth (Part No.89048)
from
$46.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dorman – Help – PCV Breather Hose (Part No.46081)
from
$28.99
Proper crankcase ventilation is key to smooth performance and engine longevity. Made from quality materials to resist cracking and brittleness, this PCV hose replaces a worn or leaking original equipment hose.
Product Features:
See More
Product Features:
- Ideal replacement – this PCV tubing replaces the original hose on specified vehicle years, makes and models
- Durable materials – this PCV hose is designed to withstand exposure to extreme temperatures and oil vapors to resist cracking and leaking
- Cost-effective solution – offers original equipment quality at a competitive price
- Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life
Litens – Serpentine Belt Tensioner Kit: Includes Belt, Tensioner, and any applicable Idler Pulleys (Part No.LV999544A)
from
$149.99
This Litens Serpentine Belt Drive Component Kit fits 2002-2006 Ford E-150, E-250 E-350, E-450, Super Duty Van w4.6/5.4/6.8L. These kits make it easy to maintain your entire front end accessory drive system. Eliminate the need to search for individual parts by purchasing this all-in-one solution. Front end accessory drives require maintenance at specific intervals, and parts should be replaced as part of your regularly scheduled tune-up to ensure your vehicle is at its best. Each kit contains a Litens belt tensioner, Bando serpentine belt, and any necessary idler pulley(s). All required hardware is included for the installation . Application specific instructions are also conveniently included. All parts meet or exceed OE fit, function, and performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Yukon Gear – Seal Puller Tool (Part No.56063)
Dayco – Flex Radiator Hoses; EPDM Rubber, 19 Inch Long, 2 Inch to 1.75 Inch Inner Dia. (Part No.81391)
from
$14.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Gates – Premium Molded Coolant Hose (Part No.21944)
from
$47.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Safety Stripe« Standard Straight Heater Hose (Part No.28409)
from
$2.49
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 8 1/4 Inch Length (Part No.86800)
from
$28.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Modular Coolant Hose (Part No.22624)
from
$257.99
Modular coolant hoses are on many of today’s vehicles and are much more complex than the standard molded hoses of the past. Modular coolant hoses are hose assemblies with one or more components built into the hose. Some examples of these components include hose branches, quick connectors, valves, sensors, bleeders and flow restrictors. Manufactured identical or equivalent to the OE hose, modular coolant hoses will keep your vehicle’s cooling system running properly and efficiently for years to come.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube: synthetic fiber knit reinforcement, heat-, ozone- and chemical coolant-resistant EPDM cover
- Manufactured with OEM-exact hose components (quick connects, branch connectors/tees, sensors, etc.)
- Meets SAE 20R3 EC Class D1 under 25mm (1 in.) ID, SAE 20R4 EC Class D1 for 25mm (1 in.) ID and over
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 18 Inch Length (Part No.80413)
from
$18.29
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Gates – Quick-Lok½ Heater Hose Connector (Part No.28500)
from
$19.49
Product Features:
See More
- Used on cars and trucks when the original quick connector fails, or the replacement hose does not include them
- Manufactured w/ a new design that retains the O-ring so they cannot get lost or damaged
- Fit just as the OEM quick connects for easy installation as well as removal
Dorman – Clip Nut – U-Type – 1/4 In.-20 X 9/16 In. (Part No.961-313D)
from
$4.49
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Gates – Premium Molded Coolant Hose (Part No.21612)
from
$28.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 21" Long, 1.69" Diameter (Part No.B71734)
from
$15.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Poly Rib Belt HD Serpentine Belt; 136.3 Long, 8 Rib Count, Heavy Duty (Part No.5081363)
from
$78.99
Produced for heavy-duty vehicles and buses with multiple accessories, Dayco HD poly-V belts are made from EPDM material to resist heat and are compliant with the latest standards, guaranteeing resistance, reliability, low noise and longer service life. En
Product Features:
See More
Product Features:
- Engineered to handle operating conditions with temperatures up to 130°C (266°F)
- Designed for multiple accessories such as A/C, power steering pumps, alternators and water pumps
- Capable of delivering excellent performance in high torque and high power pulse applications
- Specially formulated treated cord insures length and tension stability on heavy duty diesel engine drives for the life of the belt
Gates – FleetRunner« Heavy-Duty Micro-V« Serpentine Drive Belt (Part No.K081196HD)
from
$85.99
Gates FleetRunner Micro-V Belts are designed for the toughest applications. FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures, making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at prolonged extreme operating temperatures
- Heavy-duty construction resists cracking and wear, even at extreme temperatures
- Special compound provides unmatched flexibility, stability, load carrying capacity and belt life
- Problem solver designed for the toughest applications
- Consistently outperforms other heavy-duty serpentine belts on the market
- Engineered to save your fleet money and reduce downtime
- Tensioner Replacement is Recommended (if equipped)
Dorman – Steel Fuel Line: 21" Long, Threaded End 1, Quick Connect End 2 (Part No.800-863)
from
$126.99
This replacement fuel line is made to safely transfer fuel and endure in tough underhood and undercar conditions.
Product Features:
See More
Product Features:
- Trustworthy replacement – this fuel line safely replaces the original fuel line to fix fuel leaks
- Durable design – withstands tough underhood and undercar conditions
- Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience
- Comprehensive solutions – this fuel line is part of a diverse collection of fuel line repair solutions
Motorcraft – Fuel Hose (Part No.E5000672403MTR)
from
$8.26
Fuel Hose
Gates – FleetRunner« Heavy-Duty V-Belt (Part No.9490HD)
from
$34.99
Designed for the toughest applications, FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at extremely prolonged operating temperatures
- Heavy-duty construction resists cracking, wear, oil and heat
- Special compound provides unmatched stability, load carrying capacity and belt life
- Unique undercord notch pattern offers increased flexibility for smaller diameter pulleys
- Problem solver for troubled drives
- Engineered to save your fleet money and reduce downtime
- Meets RMA oil and heat resistant standards and static conductivity requirements
Dayco – Bottom Cog V-Belt; 28.5 Inch Long, Exact Fit Premium Quality (Part No.15285)
from
$10.49
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Dayco – Flex Radiator Hoses; EPDM Rubber, 17.81 Inch Long, 1.5 Inch Inner Dia. (Part No.81490)
from
$24.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13.88" Long, 2" Diameter (Part No.C70608)
from
$17.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.20355)
from
$31.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Popular 1997 Ford E-350 Econoline Belts and Hoses Categories
1997 Ford E-350 Econoline Belts and Hoses
You count on your 1997 Ford E-350 Econoline to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 75 Belts and Hoses ranging in price from $1.49 to $257.99, you’re sure to find everything you need for your 1997 Ford E-350 Econoline.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 9 different brands like Dayco, Dorman, and Litens. 1997 Ford E-350 Econoline Belts and Hoses start as low as $1.49!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 3,068 extensive product reviews on 1997 Ford E-350 Econoline Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Serpentine Belt Tensioner; 1 Piece, HD, Built To Outperform And Outlast OE Parts with 3.3 stars and Heater Hose Connector with 2.8 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1997 Ford E-350 Econoline below to get started!
Top-Rated Belts and Hoses Brands For Your 1997 Ford E-350 Econoline
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1997 Ford E-350 Econoline running right for years to come. In our inventory you’ll find brands like Dayco, Dorman, Litens, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 1997 Ford E-350 Econoline back on the road. Some of the top-rated Driveworks products in these categories are:
from
$20.99
(1)
Poly Rib Belt HD Serpentine Belt; 80.51 Long, 8 Rib Count, Heavy Duty
Serpentine Belts
from
$61.99
(2)
Poly Rib Belt HD Serpentine Belt; 99.02 Long, 8 Rib Count, Heavy Duty
Serpentine Belts
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1997 Ford E-350 Econoline, and some of our most reviewed Dayco parts include:
from
$46.99
(96)
Serpentine Idler/Tensioner Pulley; Steel, 90mm Dia., 39.5mm Width, Smooth
Drive Belt Idler Assemblies
from
$25.99
(75)
Serpentine Idler/Tensioner Pulley; Direct Fit, 76 mm Diameter, 37 mm Smooth
Idler Pulleys
from
$61.99
(31)
Serpentine Belt Tensioner; 1 Piece, HD, Built To Outperform And Outlast OE Parts
Belt Tensioner Assemblies
FAQs for 1997 Ford E-350 Econoline Belts and Hoses
What are the most purchased Belts and Hoses for the 1997 Ford E-350 Econoline?
Out of 75 Belts and Hoses for the 1997 Ford E-350 Econoline, the most popular in our inventory are:
from
$50.99
(10)
Poly Rib Belt HD Serpentine Belt; 119.09 Long, 8 Rib Count, Heavy Duty
Serpentine Belts
from
$56.99
(5)
Poly Rib Belt HD Serpentine Belt; 99.02 Long, 8 Rib Count, Heavy Duty
Serpentine Belts
What are the top-rated 1997 Ford E-350 Econoline Belts and Hoses?
Top-rated Belts and Hoses for your 1997 Ford E-350 Econoline based on customer reviews/ratings are:
from
$75.99
(7)
Serpentine Belt Tensioner; 1 Piece, HD, Built To Outperform And Outlast OE Parts
“Exact fit quick delivery.”
from
$15.49
(6)
Heater Hose Connector
“Used 2 connectors each when replacing blend door – one 5/8″ and one 3/4″. Had to cut factory hose and attach to connector with a normal hose clamp. ”
from
$32.49
(5)
Serpentine Idler/Tensioner Pulley; Direct Fit, 76 mm Diameter, 8 Grooves
“High quality good value for the money.”
