1997 Chevrolet P30 Drivetrains
Find Your Specific 1997 Chevrolet P30 Drivetrains
Below you will find various in-demand Chevrolet Drivetrains, components and accessories for your 1997 P30. Advance Auto Parts has popular P30 parts like Drive Shafts and Axles, Universal Joints, Differentials and more. You’ll also find aftermarket and OEM Drivetrains for other P30 model years including
1990,
1991,
1992,
1993,
1994,
1995,
1996,
1998,
1999 and more. Select a category of 1997 Chevrolet P30 Drivetrains below and start saving instantly.
Popular 1997 Chevrolet P30 Drivetrains Categories
Essential Drivetrains for 1997 Chevrolet P30s
Yukon Gear – U/Joint Strap Bolt For 14T, 7.5", And 8.5" GM (Part No.33351)
from
$8.49
U/joint strap bolt for 14T, 7.5″, and 8.5″ GM.
Product Features:
See More
Product Features:
- u-joint strap bolt for GM 10.5″ 14 bolt truck, 7.5″ and 8.5″
Schaeffler – Shaft Seal (Part No.SS3147)
from
$32.49
Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.
Product Features:
See More
Product Features:
- High-precision and High-quality components used in all KITs
- Coverage of classic and new high-tech solutions for the best system coverage
Driveworks – Tapered Roller Bearing (Part No.S-HM-807046)
Yukon Gear – Dana 50 Dana 60 Dana 70 & Dana 80 Roll Pin, 0.225" Dia, For X/P Shaft, 1.87" Lng (Part No.33327)
from
$7.99
Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.
Product Features:
See More
Product Features:
- Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
- 0.225″ diameter
- 1.870″ long
Yukon Gear – Steel Cover For Dana 80 (Part No.32323)
Yukon Gear – Replacement Cover Gasket For Dana 50, Dana 60 & Dana 70 (Part No.23007)
Yukon Gear – Pinion Install Kit For ’89 To ’98 10.5" GM 14 Bolt Truck Differential (Part No.13059)
from
$404.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits 1989-1997 GM 10.5″ 14 bolt truck
- Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.
Yukon Gear – Plug Adapter For Extra-Large Clamshell (Part No.56070)
from
$47.99
Plug adapter for extra-large clamshell. No Return.
Product Features:
See More
Product Features:
- Plug adapter for Extra Large clamshell
- Fits carrier bearing puller
Powertrax – Grip PRO Traction System (Part No.GT436035)
from
$596.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!
See More
Yukon Gear – DiffrlPinSupportBolt (Part No.33582)
from
$5.99
DiffrlPinSupportBolt
Motive Gear – Axle Shaft (Part No.MG1774)
from
$175.99
The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.
Product Features:
See More
Product Features:
- AXLE SHAFT 10.5″ 30 SPL. 37 9/16″ R.H.
Motive Gear – Differential Crush Sleeve (Part No.26008741)
Yukon Gear – Dana 60 & Dana 70 Power Lok Clutch Set (Steel & Fiber) (Part No.16155)
from
$181.99
Dana 60 & Dana 70 Power Lok clutch set (steel & fiber).
Product Features:
See More
Product Features:
- Clutch kit
- Fit Dana Spicer 60, 70, 70U and 70HD Powr Lok positraction
Driveworks – Tapered Roller Bearing (Part No.S-M-802048)
Spicer – Universal Joint (Part No.5-795X)
from
$48.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
Yukon Gear – Bearing Race Driver (Part No.56013)
from
$215.99
Bearing race driver. No return.
Product Features:
See More
Product Features:
- Bearing race driver
- Fits HM807010 race
- All steel construction
Pro-King – Differential Bolt (Part No.718A935)
from
$8.29
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- Meets or exceeds OE specifications
Motive Gear – Differential Gear Install Kit (Part No.GM10.5IKLA)
from
$52.79
All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!
See More
Driveworks – Tapered Cup Wheel Bearing Assembly (Part No.S-382-A)
from
$8.99
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – Replacement Yoke For Dana 80 With A 1410 U/Joint Size (Part No.41034)
from
$334.99
Yukon replacement yoke for Dana 80 with a 1410 U/joint size. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 80
- 37 spline
- 1410 u-joint size
- 4.188″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
Motive Gear – Differential Bearing Kit – Timken (Part No.R80RT)
from
$211.99
Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv
Product Features:
See More
Product Features:
- KIT BRG & SEAL DANA 80
Yukon Gear – Replacement Outer Oil Slinger For Dana 60, 70, 70U & 70HD (Part No.33019)
Yukon Gear – GM 10.5′ 14 Bolt Truck Cover Gasket (Part No.23016)
Yukon Gear – Replacement Pinion Nut For Dana 80 (Part No.33145)
from
$26.99
Replacement pinion nut for Dana 80, 1 7/8″ socket.
Product Features:
See More
Product Features:
- Pinion nut for Dana Spicer 80
- 1 7/8″ socket
Dorman – U-BOLT KIT (Part No.929-736)
from
$78.99
The components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of an axle of a vehicle or trailer. Check the leaf spring dimensions and other relevant application details to select the right type and size U-bolt kit for your needs.
Product Features:
See More
Product Features:
- Reliable hardware – the components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of a vehicle or trailer axle
- Check fit – carefully review the dimensions of the leaf springs that will be used and other relevant application details to select the right type and size U-bolt kit for your needs
- Durable construction – the components in this kit are engineered from quality materials for reliable performance and long service life
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Powertrax – No-Slip Traction System (Part No.9207053000)
from
$591.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles. Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction. Powertrax® = Extreme Traction Systems!
See More
Yukon Gear – Replacement Carrier Shim Kit For Dana 60, 70, 70HD, 70U & 80 (Part No.55011)
Yukon Gear – Replacement Pinion Nut Washer For Dana 80 (Part No.33165)
Upgrade your 1997 Chevrolet P30 with Top-Quality Drivetrains
When it comes to maintaining or upgrading your 1997 Chevrolet P30, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Chevrolet or enhancing its overall performance, Drivetrains are key to keeping your P30 functioning at its best. At Advance Auto Parts, we offer a wide selection of 337 Drivetrains for the 1997 Chevrolet P30, designed to meet your needs without breaking the bank.
From
Drive Shafts and Axle
replacements to
Universal Joints
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1997 Chevrolet P30 at great prices.
Our Drivetrains inventory for this model
ranges from just $1.89 to $2,374.99, with
an average price of $362.80.
Our 337 Drivetrains in stock come from 18 trusted brands, so you’re sure to find the right part for your 1997 Chevrolet P30 without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1997 Chevrolet P30, we stock popular OEM and aftermarket Drivetrains from top names
like Spicer, Felpro, National, and more.
Spicer Drivetrains
start at just $44.99 and boast an impressive 4.6 stars average rating from customers.
Felpro and National also bring quality to the table, with Drivetrains available starting at $5.79, and at an average 4.6 stars rating.
With 3,768 customer reviews and counting, our 1997 Chevrolet P30 Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1997 Chevrolet P30 is always ready to roll. We’re committed to providing you with everything you need to keep your P30 in top shape, all in one place.
Start shopping confidently below for your 1997 Chevrolet P30!
Best-Selling Drive Shafts and Axles for 1997 Chevrolet P30s
Enhance the driving experience in your Chevrolet with 30 quality Drive Shafts and Axle components, starting at $5.29.
Spicer – Universal Joint, Greaseable 1410 Series (Part No.5-160X)
from
$45.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.
Product Features:
See More
Product Features:
- OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
- Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
- The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
- Zerk allows for lubricating at regular intervals to help extend the life of the part.
Spicer – Universal Joint (Part No.5-1410X)
from
$54.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)
from
$40.99
Anchor 6038 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 4 Lbs
- BEARING ID / BORE: 1.5750 In. / 40 mm
- CENTERLINE: 2.48 In. / 63 mm
- Mount Width: 6.62 In. / 168 mm
- Style: Round Frame
- Not Pictured: Two Dust Shields
Felpro – Drive Axle Shaft Flange Gasket 8 Bolt Hole Gasket, 2.719 Inch Inside Diameter, 4.438 Inch Outside Diameter (Part No.55350)
from
$5.79
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Spicer – Universal Joint, Greaseable 1350 Series (Part No.5-178X)
from
$44.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.
Product Features:
See More
Product Features:
- OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
- Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
- The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
- Zerk allows for lubricating at regular intervals to help extend the life of the part.
Spicer – Universal Joint (Part No.5-1350X)
from
$45.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
National – Drive Shaft Center Support Bearing (Part No.HB-88508-AA)
from
$58.99
Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.
Product Features:
See More
Product Features:
- BUILT TO LAST – Advanced heat treatment process for strength
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
- RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)
from
$21.99
Anchor 6056 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.3780 In. / 35 mm
- CENTERLINE: 2.28 In. / 58 mm
- Mount Width: 6.62 In. / 168 mm
- Style: Round Frame
- Complete Mount
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6053)
from
$38.99
Anchor 6053 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1960-2015
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.5750 In. / 40 mm
- CENTERLINE: 2.28 In. / 58 mm
- Mount Width: 6.62 In. / 168 mm
- No Studs
National – Drive Shaft Center Support Bearing (Part No.HB-88508-AB)
from
$50.99
Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.
Product Features:
See More
Product Features:
- BUILT TO LAST – Advanced heat treatment process for strength
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
- RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Yukon Gear – Yoke For GM 10.5" 14 Bolt Truck, 1350, Strap Style (Part No.41179)
from
$249.99
Yukon yoke for GM 10.5″ 14 bolt truck, 1350, strap style. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits GM 10.5″ 14 bolt truck
- 30 spline
- 1350 u-joint size
- 3.625″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
Yukon Gear – Yoke For GM 10.5" 14 Bolt Truck, 1410, Strap Style (Part No.41180)
from
$299.99
Yukon yoke for GM 10.5″ 14 bolt truck, 1410, strap style. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits GM 10.5″ 14 bolt truck
- 30 spline
- 1410 u-joint size
- 4.188″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6027)
from
$5.29
Anchor 6027 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2012
- Weight approx: 1 Lbs
- Cushion insert only
- For complete mount see part 6056
Yukon Gear – Pinion Yoke Dust Shield For Dana 60 & 70 (Part No.33441)
Yukon Gear – Replacement Yoke For Dana 80 With A 1410 U/Joint Size (Part No.41034)
from
$334.99
Yukon replacement yoke for Dana 80 with a 1410 U/joint size. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 80
- 37 spline
- 1410 u-joint size
- 4.188″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
Dorman – Differential Pinion Yoke Assembly (Part No.697-547)
from
$279.99
Worn or damaged differential end yoke causing driveline vibrations- This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this differential end yoke matches the fit and construction of the original yoke
- Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
- Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
- Validated fit – this differential end yoke has been tested to confirm accurate fit
Yukon Gear – Billet Replacement Yoke For Dana 60 And 70 With 29 Spline Pinion And A 1350 U/Joint Size (Part No.41138)
from
$414.99
Yukon billet replacement yoke for Dana 60 and 70 with 29 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 and 70
- 29 spline
- 1350 u-joint size
- Outside snap ring design
- 3.625″ snap ring span
- 1.188″ cap diameter
- U-bolt style
Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1330 U/Joint Size (Part No.41025)
from
$271.99
Yukon replacement yoke for Dana 60 and 70 with a 1330 U/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects. This is a u/bolt style yoke.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 and 70
- 29 spline
- 1330 u-joint size
- Outside snap ring design
- 3.625″ snap ring span
- 1.062″ cap diameter
- U-bolt style
Yukon Gear – Replacement Yoke For Dana 44-HD, 60, And 70 With A 1310 U/Joint Size (Part No.41022)
from
$233.99
Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 and 70
- 29 spline
- 1310 u-joint size
- Outside snap ring design
- 3.219″ snap ring span
- 1.062″ cap diameter
- Strap style
Yukon Gear – Extra-Large Clamshells For Large Applciations (Part No.56059)
from
$209.99
Extra large clamshells for use with Dana 70HD, Dana 80, AAM 11.5″, Ford 9.75″, Ford 10.25″ & Ford 10.5″.
Product Features:
See More
Product Features:
- Extra Large clamshell
- Fits carrier bearing puller
Spicer – Drive Shaft Center Support Bearing (Part No.211793-1X)
from
$88.99
The part you need. The name you trust. Spicer driveline components deliver top performance and value. These center bearing kits are manufactured to the same genuine standards you’ve come to expect from the most reliable name in driveshaft parts.
Product Features:
See More
Product Features:
- Dana manufactured Spicer center bearing kit
- Interchangeable with OE component
- Comes as a complete kit to replace, repair, or refurbish
- Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace
Dorman – U-BOLT KIT (Part No.929-736)
from
$78.99
The components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of an axle of a vehicle or trailer. Check the leaf spring dimensions and other relevant application details to select the right type and size U-bolt kit for your needs.
Product Features:
See More
Product Features:
- Reliable hardware – the components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of a vehicle or trailer axle
- Check fit – carefully review the dimensions of the leaf springs that will be used and other relevant application details to select the right type and size U-bolt kit for your needs
- Durable construction – the components in this kit are engineered from quality materials for reliable performance and long service life
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Spicer – Drive Shaft Center Support Bearing (Part No.211260X)
from
$66.99
Demand genuine Spicer. Dana design, engineering, testing and manufacturing processes all work in conjunction with one another to ensure unparalleled performance that non genuine parts simply cannot deliver.
See More
Spicer – Drive Shaft Center Support Bearing (Part No.210873-1X)
from
$52.99
The part you need. The name you trust. Spicer driveline components deliver top performance and value. These center bearing kits are manufactured to the same genuine standards you’ve come to expect from the most reliable name in driveshaft parts.
Product Features:
See More
Product Features:
- Dana manufactured Spicer center bearing kit
- Interchangeable with OE component
- Comes as a complete kit to replace, repair, or refurbish
- Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace
Most Popular 1997 Chevrolet P30 Universal Joints
Customize your Chevrolet with 31 Universal Joints products
like U-Joints,
U-Joint Strap Kits, and
U-Joint U-Bolt Kits, all
priced under $203.99.
Driveworks – Universal Joint (Part No.DW-331BL)
from
$15.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Driveworks – Universal Joint (Part No.DW-331)
from
$15.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Driveworks – Universal Joint (Part No.DW-330)
from
$46.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Dorman – Help – U-Joint Repair Assortment 2 Pc (Part No.81020)
from
$16.99
This universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
- Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
- Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Neapco – Universal Joint (Part No.2-0053)
Yukon Gear – Adapter Sleeve Fro GM 11.5" & 10.5" 14 Bolt Truck Yokes To Use Triple Lip Pinion Seal (Part No.41209)
from
$29.99
Product Features:
See More
- Adapter sleeve
- Fits GM 10.5″ 14 bolt truck and GM 11.5″
- Converts to triple lip seal
Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)
from
$59.99
Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.
See More
Yukon Gear – 1350 & 1410 U/Joint U-Bolts, 3/8" X 1-11/16", Kit (Part No.41190)
from
$16.99
1350 & 1410 U/joint U-bolts, 3/8″ X 1-11/16″, kit.
Product Features:
See More
Product Features:
- u-joint u-bolt kit
- Fits 1350 and 1410 u-joint size
- Includes two u-bolts and four nuts
Yukon Gear – 1350 To 1410 Conversion U/Joint (Part No.42006)
Yukon Gear – U/Joint Strap For GM 14T (Part No.41200)
from
$9.99
Product Features:
See More
- U-joint strap
- Fits GM 10.5″ 14 bolt truck
- 1350 and 1410 u-joint size
- One single strap
Yukon Gear – 1310 To Mechanics 3R Adapter U/Joint (Part No.42013)
Yukon Gear – 1350 Lifetime Series U/Joint (Part No.42021)
from
$63.99
Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.
See More
Yukon Gear – 1480 Lifetime Series U/Joint (Part No.42023)
from
$98.99
Yukon 1480 Lifetime Series U/Joint. 4.188″ span ring span. 1.375″ cap diameter. Outside snap ring. This U/Joint is a driveline U/Joint.
See More
Yukon Gear – 1350 U/Joint With Zerk Fitting (Part No.42010)
from
$51.99
Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.
See More
Dorman – Help – U-Joint Repair Kit (Part No.81019)
from
$16.99
This universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
- Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
- Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Yukon Gear – 1480 U-Bolt Kit (Part No.41191)
Yukon Gear – 1330 Lifetime U/Joint (Part No.42004)
from
$53.99
1330 Yukon Lifetime U/Joint. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring.
See More
Yukon Gear – 1310 Lifetime U/Joint (Part No.42003)
from
$57.99
1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.
See More
Yukon Gear – Replacement Yoke For Dana 44-HD, 60, And 70 With A 1310 U/Joint Size (Part No.41023)
from
$203.99
Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60, 70, 70U and 70HD
- 29 spline
- 1310 u-joint size
- 3.219″ snap ring span
- 1.062″ cap diameter
- Outside snap ring design
- U-bolt style
Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1330 U/Joint Size (Part No.41024)
from
$187.99
Yukon replacement yoke for Dana 60 and 70 with a 1330 U/joint size. 3.625″ snap ring span, 1.0625″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects. This is a strap style yoke.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60, 70, 70U and 70HD
- 29 spline
- 1330 u-joint size
- 3.625″ snap ring span
- 1.062″ cap diameter
- Outside snap ring design
- Strap style
Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1350 U/Joint Size (Part No.41026)
from
$179.99
Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60, 70, 70U and 70HD
- 29 spline
- 1350 u-joint size
- 3.625″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
Yukon Gear – 1350 To Mechanics 3R Adaptor U/Joint (Part No.42001)
Yukon Gear – 1410 Lifetime Series U/Joint (Part No.42022)
from
$84.99
Yukon 1410 Lifetime Series U/Joint. 4.188″ span ring span. 1.188″ cap diameter. Outside snap ring.
See More
Yukon Gear – 1410 U/Joint With Zerk Fitting (Part No.42009)
from
$61.99
Yukon 1410 U/Joint with zerk fitting. 4.188″ snap ring span, 1.118″ cap diameter. Outside snap ring.
See More
Top Picks for 1997 Chevrolet P30 Differentials
Upgrade Chevrolet P30s with top-quality Differentials parts, including 257 OEM and aftermarket selections for your 1997 model.
Valvoline – MaxLife Multi-Vehicle Automatic Transmission Fluid, 1 Gallon (Part No.773775)
from
$35.99
Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life. Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.
Product Features:
See More
Product Features:
- Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
- High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
- Developed with anti-wear technology to help improve transmission durability
- Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
National – Bearing Race (Part No.382A)
from
$13.99
Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Felpro – Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (Part No.RDS 55447)
from
$16.99
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Validated for fit, form and function
- Unsurpassed quality you can trust
Felpro – Axle Housing Cover Gasket: Irregular Shaped 14 Bolt Hole Gasket (Part No.RDS 55063)
from
$8.29
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Validated for fit, form and function
- Unsurpassed quality you can trust
Dorman – Differential Cover (Part No.697-703)
from
$46.99
This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.
Product Features:
See More
Product Features:
- Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
- Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
- Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
National – Multi-Purpose Seal (Part No.710508)
from
$28.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Design type: spring loaded; multi-lip
- Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
- Excellent high temperature capabilities
- Compatible with wide range of fluids
- Delivers quality and reliable performance for every type of repair
Motive Gear – Differential Ring and Pinion (Part No.D70-410)
Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)
from
$57.99
3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.
Product Features:
See More
Product Features:
- Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive
Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)
from
$44.99
3 Qt. Penzoil 80W90 conventional gear Oil.
Product Features:
See More
Product Features:
- Includes three quarts of conventional oil
Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)
from
$5.99
3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.
Product Features:
See More
Product Features:
- Cover bolt for Dana Spicer 60, 70 and 80
- 3/8″
Yukon Gear – Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (Part No.33037)
from
$4.99
Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.
Product Features:
See More
Product Features:
- Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
- 1/2″ x 18 thread
Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)
from
$37.99
Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.
Product Features:
See More
Product Features:
- Redi-Sleeve yoke saver
- Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD
Yukon Gear – Repleacement Ring Gear Bolt For Dana 80 (Part No.33039)
from
$7.99
Repleacement ring gear bolt for Dana 80. 9/16″ x 18.
Product Features:
See More
Product Features:
- Ring gear bolt for Dana Spicer 80
- 9/16″ x 18 thread
Yukon Gear – Replacement Carrier Shim Kit For Dana 60, 70, 70HD, 70U & 80 (Part No.55011)
Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)
from
$148.99
Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.
Product Features:
See More
Product Features:
- Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive
Motive Gear – Differential Pinion Seal (Part No.9316)
from
$16.49
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.
See More
Motive Gear – Differential Pinion Shim Kit (Part No.1118)
National – Tapered Roller Bearing Cone (Part No.HM903249)
from
$43.99
Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)
from
$99.99
Redline Synthetic “Shock Proof” Oil. 3 Quarts.
Product Features:
See More
Product Features:
- Includes three quarts of Redline Shockproof oil
National – Tapered Roller Bearing Cone (Part No.HM807046)
from
$61.99
Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
National – Tapered Roller Bearing Cone (Part No.469)
from
$43.99
Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
National – Bearing Race (Part No.HM903210)
from
$28.49
Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
National – Bearing Race (Part No.HM807010)
from
$26.99
Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)
from
$137.99
Redline Synthetic “Shock Proof” Oil. 4 Quarts.
Product Features:
See More
Product Features:
- Includes four quarts of Redline Shockproof oil
In-Demand Transfer Cases for 1997 Chevrolet P30s
Select from 9 premium Transfer Cases parts for your 1997 Chevrolet P30, with prices ranging from $8.99 to $37.99.
National – Multi-Purpose Seal (Part No.9449)
from
$12.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Design type: spring loaded; multi-lip
- Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
- Good low temperature capability
- Low swell in hydrocarbon fluids
- Delivers quality and reliable performance for every type of repair
National – Shaft Repair Sleeve (Part No.99199)
from
$37.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
Driveworks – Taper Bearing Set (Part No.S-A-3)
from
$8.99
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Driveworks – Tapered Cup Wheel Bearing Assembly (Part No.S-382-A)
from
$8.99
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
National – Multi-Purpose Seal (Part No.5208)
from
$20.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Design type: spring loaded; multi-lip
- Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
- Good low temperature capability
- Low swell in hydrocarbon fluids
- Delivers quality and reliable performance for every type of repair
Driveworks – Oil Seal (Part No.S-4333N)
from
$13.49
Value-priced seal meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Driveworks – Tapered Roller Bearing (Part No.S-M-802048)
USA Standard Gear – Shift Fork Insert (Part No.71380)
from
$11.99
Shift Fork Insert
Schaeffler – Shaft Seal (Part No.SS2960)
from
$9.59
Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.
Product Features:
See More
Product Features:
- High-precision and High-quality components used in all KITs
- Coverage of classic and new high-tech solutions for the best system coverage
Most Sold 1997 Chevrolet P30 CV Axles and Joints
Explore our best-selling Chevrolet parts for the 1997 P30 among 1 OEM and aftermarket options starting from $14.49.
Sealed Power – Engine Balance Shaft Bearing (Part No.3204DR)
from
$14.49
Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.
Product Features:
See More
Product Features:
- Steel-backed Babbitt lining material
- Used in automotive and high-performance
- Babbitt is designed to perform under extreme loads w/o damaging other engine parts
- Babbitt is more environmentally friendly than other material
- ISO & QS certified manufacturing
Top-Rated Drivetrains Brands For Your 1997 Chevrolet P30
Shop for the best-rated brands offering Drivetrains and other products for your 1997 Chevrolet P30s. Below you’ll find some of our best rated Drivetrains from Spicer, Felpro, and National, and more. Drivetrains from these brands that fit a 1997 P30 start at just $5.79 and are rated as high as 4.6 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.
Popular Spicer 1997 Chevrolet P30 Drivetrains
When it comes to maintaining or upgrading your 1997 Chevrolet P30, using quality Drivetrains is essential to ensure durability and a perfect fit. Spicer ticks all of those boxes. We offer a wide selection of Spicer Drivetrains, specifically designed for the 1997 Chevrolet P30. With over 3 Spicer brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $44.99, with an average price of just $48.66. Plus, with over 16 customer reviews and an average rating of 4.6 stars, you can trust that our Spicer Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
Popular Felpro 1997 Chevrolet P30 Drivetrains
Felpro auto parts is one of the highest quality Drivetrain brands in the market. Any 1997 Chevrolet P30 owner should feel confident when installing genuine Felpro parts in their vehicle. To ensure the best fit and performance for your 1997 P30, Advance Auto Parts carries a full inventory of 3 Felpro Drivetrains. Plus you will be keeping your Chevrolet in peak condition while saving money because prices on these Felpro Drivetrains range from $5.79 to $16.99, plus, with more than 25 customer reviews and an impressive 4.6 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.
from
$5.79
(11)
Drive Axle Shaft Flange Gasket 8 Bolt Hole Gasket, 2.719 Inch Inside Diameter, 4.438 Inch Outside Diameter
“The product was exact fit to the original and was great priced as well.”
from
$16.99
(1)
Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket
“appears to be the right one, haven’t installed yet.”
FAQs for 1997 Chevrolet P30 Drivetrains
Which Drivetrains are best-sellers for 1997 Chevrolet P30s?
Out of 337 Drivetrains that fit 1997 Chevrolet P30s, the following parts are the top sellers:
- Taper Bearing Set (5050502) – $8.99
- Universal Joint (10265721) – $15.99
- Drive Axle Shaft Flange Gasket 8 Bolt Hole Gasket, 2.719 Inch Inside Diameter, 4.438 Inch Outside Diameter (19780167) – $5.79
What’s the price range for 1997 Chevrolet P30 Drivetrains?
Drivetrain prices for the 1997 Chevrolet P30 start at $1.89 and go up to $2,374.99 for the most premium parts.
What’s the average price of a Drivetrain for a 1997 Chevrolet P30?
The average price for Drivetrains for the 1997 Chevrolet P30 is $362.80. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Drivetrains for other Chevrolet P30 model years?
What are the cheapest Drivetrains for my 1997 Chevrolet P30?
The cheapest 1997 Chevrolet P30 Drivetrains we carry in stock are:
- Differential Ring Gear Bolt (10282457) – $1.89
- Spindle Washer – I.D. 27/32 In. O.D. 2-1/16 In. Thickness 11/64 In. (11236158) – $4.29
- Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (11643357) – $4.99
- Side Gear Thrust Washer For Dana 60, 70 & 80 (11642996) – $4.99
- Spindle Washer – I.D. 27/32 In. O.D. 2-1/16 In. Thickness 11/64 In. (Sold by each) (22148863) – $4.99
What are the top-rated Drivetrains that fit the 1997 Chevrolet P30?
Out of 3,768 reviews by customers, our 1997 Chevrolet P30 Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1997 Chevrolet P30 and their top-rated products:
- Spindles
- Spindle Nut Key (11115444) – $15.49
- Universal Joints
- Spindle Nut Key (11115444) – $15.49
- Differentials
- Spindle Nut Key (11115444) – $15.49
What types of Drivetrains do you sell for my 1997 Chevrolet P30?
As of 3/1/26, these are some of the most in-demand types of Drivetrains for a 1997 Chevrolet P30:
Can I get help with 1997 Chevrolet P30 Drivetrain orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Chevrolet Drivetrains and more.
What is your return policy for Chevrolet P30 Drivetrains?
Advance Auto Parts keeps returns simple. For new Chevrolet P30 Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
