1996 Chevrolet C3500HD Differentials

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 1998 and up GM 10.5″ 14 bolt truck
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Product Features:

• DANA-60 R/P 3.54 STD MG 24813-5X (USES PRE-LOAD SHIMS)

Product Features:

• Pinion nut washer
• Fits Dana Spicer 80

Yukon replacement standard open spider gear kit for Dana 70 and 80 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

• Includes three quarts of Redline Shockproof oil

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

Chrome replacement cover for Dana 80.

Product Features:

• Fits Dana Spicer 80
• Chrome

Dana 80 TracLoc clutch set round design (remove 4 plates 4 V-Type).

Product Features:

• Clutch kit
• Fit Dana Spicer 80 Trac Loc positraction

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1998 and up GM 10.5″ 14 bolt truck
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Pinion seal with triple-lip design for ’98 and newer GM 14T.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits 1998 and up GM 10.5″ 14 bolt truck

Product Features:

• Brand may vary by location

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

Yukon mini spool for GM 10.5″ 14 bolt truck.

Product Features:

• Fits 10.5″ GM 14 bolt truck
• Provides 100% traction to both wheels at all times
• Installs into standard open carrier case

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits 1998 and up GM 10.5″ 14 bolt truck
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, pilot bearing, marking compound and brush.

Set-up carrier bearing kti (2 bearings, no races) for Dana 70 HD and Dana 80. 469. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 80
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

Product Features:

• Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

Differential

Yukon replacement standard open spider gear kit for Dana 80 with 37 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 80 open differential with 37 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Replacement pinion nut for Dana 80, 1 7/8″ socket.

Product Features:

• Pinion nut for Dana Spicer 80
• 1 7/8″ socket

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

10.5″ GM 14 bolt truck crush sleeve, 1989 & newer. Approx 0.920″ long.

Product Features:

• Crush sleeve for 1989 and up GM 10.5″ 14 bolt truck
• 0.920″ tall

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits GM 10.5″ GM 14 bolt truck
• 10.50″ ring gear diameter
• 30 spline pinion
• 12 ring gear bolts
• 4.56 ratio
• Thick gear for 4.10 and down carrier

Yukon replacement yoke for Dana 80 with a 1550 U/joint size. 4.964″ snap ring span, 1.375″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Standard Open cross pin shaft for four pinion design for GM 14T.

Product Features:

• Cross pin shaft
• Fits GM 10.5″ 14 bolt truck

DiffrlPinSupportBolt

Product Features:

• Oil baffle
• Fits Dana Spicer 80

Differential Pinion

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″