1994 Chevrolet C3500HD Differentials

Polished aluminum replacement cover for Dana 80.

Product Features:

• Fits Dana Spicer 80
• Finned polished aluminum

14T pinion gear Thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits GM 10.5″ 14 bolt truck

Replacement pinion nut for Dana 80, 1 7/8″ socket.

Product Features:

• Pinion nut for Dana Spicer 80
• 1 7/8″ socket

Product Features:

• Spider gear kit
• Fit Dana Spicer 70 and 80 open differential with 35 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Differential Cover B

Yukon spider gear set for GM 10.5″ 14 bolt truck Yukon Dura Grip posi. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY. Will not work with factory Gov Loc.

Product Features:

• Spider gear kit
• Fits GM 10.5″ 14 bolt truck with Dura Grip positraction
• Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Product Features:

• Oil baffle
• Fits Dana Spicer 80

Yukon replacement standard open carrier case for Dana 80, 4.10 & up, (incl ABS) 35 & 37 spline.

Product Features:

• Standard open carrier case
• Fits Dana Spicer 80
• 4.10 and up ratio only
• Does not include spider gears

Product Features:

• DANA-60 R/P 3.54 STD MG 24813-5X (USES PRE-LOAD SHIMS)

Pro-King is the leading supplier of transmission and driveline products in the aftermarket. All products are designed to meet or exceed OE quality, form, fit and funtion.

Product Features:

• High strength steel
• Dual heat treating process

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits Dana Spicer 80
• 11.25″ ring gear diameter
• 37 spline pinion
• 12 ring gear bolts
• 3.73 ratio

Product Features:

• Complete shim kit for Dana Spicer 80
• 4.125″ O.D. pinion bearing application only

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Pilot bearing for 10.5″ 14 bolt truck, 2.050″ O.D.

Product Features:

• Pilot bearing
• Fits GM 10.5″ 14 bolt truck
• 2.050″ O.D.

Set-up carrier bearing kti (2 bearings, no races) for Dana 70 HD and Dana 80. 469. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 80
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• GM11.5″ BEARING & SEAL KIT

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

• Fits GM 10.5″ 14 bolt truck
• 4.10 ratio and down only
• Clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1998 and up GM 10.5″ 14 bolt truck
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Product Features:

• Pinion nut washer
• Fits Dana Spicer 80

Differential

Plug adapter for extra-large clamshell. No Return.

Product Features:

• Plug adapter for Extra Large clamshell
• Fits carrier bearing puller

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

Dana 80 TracLoc clutch set round design (remove 4 plates 4 V-Type).

Product Features:

• Clutch kit
• Fit Dana Spicer 80 Trac Loc positraction

Dana 70 & Dana 80 standard Open cross pin shaft, one piece case.

Product Features:

• Cross pin shaft
• Fits Dana Spicer 70 and 80

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM903210 race
• All steel construction

Yukon Performance steel spool for 8Dana 80 with 35 spline axles, 4.10 & up. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler Dana Spicer 80 with 35 spline axles
• 4.10 and up ratio only
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles