1995 GMC K1500 Performance Engines

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 64cc Combustion Chambers Improve Performance
• Retain Stock Compression Ratio

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Xtreme Energy: Pro Street/bracket, needs good intake, headers, gear and 3300+ stall.

Product Features:

• Cam and lifter kit for Small Block Chevy engines
• CL-Kit includes cam, lifters, assembly lube, instructions and decals
• HYDRAULIC – Xtreme Energy: Pro Street/bracket, needs good intake, headers, gear and 3300+ stall.
• 294/306 Advertised Duration, 250/256 Duration @ .050″, .519″/.523″ Lift, 110 Lobe Separation
• Valve spring upgrade required

Product Features:

• Case-Hardened Tubing
• Welded Ends
• 5/16 in. Diameter
• Use with or without Hardened Steel Guideplates

Product Features:

• Head: 4.370″ Bore/0.039″ Thick/9.70cc Vol.
• Intake: 1.82″x2.54″ Port/.060″ Thick
• Exhaust: 1.940″ Round Port
• 5/16″ Valve Cover
• Multi Piece Configuration

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Die cut silicone rubber gaskets conform to out-of-flat covers
• Great for on-again/off-again situations
• Not intended for use in emission controlled vehicles.

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Product Features:

• Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
• 3/8 inch-16 by 1 inch bolts
• Kit includes 12 bolts and washers
• Manufactured from high quality steel
• Bolts feature hex heads

Includes: 2 short chrome valve covers 2 valve cover gaskets 1 chrome push-on breather 1 chrome dipstick & tube 1 chrome timing chain cover 1 chrome timing tab 1 rubber grommet for valve cover PCV hole 1 breather grommet.

Product Features:

• Chrome Plated Steel
• Comes W/valve Cover Gaskets

High Energy Hydraulic Flat Lifter Chevrolet SBC, BBC, and 194-292/200-262 V6.

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets
• 50 State Street Legal

HYDRAULIC – Xtreme Energy: Street/strip, 2800+ stall, rough idle. 9.5:1+ compression.

Product Features:

• HYDRAULIC – Xtreme Energy: Street/strip, 2800+ stall, rough idle. 9.5:1+ compression.
• 284/296 Advertised Duration, 240/246 Duration @ .050″, .574″/.578″ Lift, 110 Lobe Separation
• Valve spring upgrade required
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Grade 8 Steel

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Prevents Stud Flexing
• Black Plated Finish

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longevity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.
• Not intended for use in emission controlled vehicles.

Product Features:

• 2000-6500 RPM Power Band
• Single Plane/Open Plenum Design
• No Provision For Divorced Or Hot Air Choke
• Square Flange Carburetor Mounting

Product Features:

• Mounts Standard Flange Holley Carbs Sideways
• Use on Tunnel Rams
• 0.550 in. Thick

Product Features:

• Non-Rotator
• 1.500 in. Outside Diameter
• 1.082 in. Inside Diameter
• 1.340 in. Coil Blind
• Set of 16

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• Complete Kit: Includes Retainers And Locks
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Includes Superior Quality Steel Retainers
• Includes 7 deg. Heat-Treated Valve Stem Locks
• Retainers and Locks Black Oxide Coated
• Non-Rotator Style: Dyno Tested and Street Proven
• Great Match to Edelbrock Camshaft Kit

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
• Not intended for use in emission controlled vehicles.

VALVE SEALS, O-RING 11/32″ 1 ST

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

• Work with .530″ guides and 11/32″ valve stem diameter
• Valve stem oil seals keep unwanted oil from entering the combustion chamber
• Several different types of valve seals are offered

Secure the harmonic balancer or dampener on your Chevy. Works on original equipment, high performance street, drag or circle track applications. Features a heat treated black oxide coated Grade 8 alloy steel bolt for strength with a tall hex head to prevent wrench from slipping. An extra thick parallel ground washer provides accurate, uniform torque, and a lock washer is also included.

Product Features:

• Heat treated black oxide coated Grade 8 alloy steel
• Tall hex head bolt to prevent wrench from slipping
• Extra thick parallel ground washer provides accurate, uniform torque
• Washers Provides More Accurate And Uniform Torque
• Grade 8 Alloy Steel

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

• These Are Have A Zinc Dichromate Finish
• Tall Hex Head Bolt To Prevent Slippage
• Extra Thick Parallel Ground Washer
• Washers Provides More Accurate And Uniform Torque
• Grade 8 Alloy Steel