from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

from

$41.49

Spectre’s High Performance Replacement Air Filters are engineered to outperform ordinary paper filters by providing increased air flow for improved performance. Manufactured using high quality materials including pre-dyed synthetic media, urethane, and steel mesh, this performance air filter is factory pre-oiled and ready to use. Use a Spectre Accucharge cleaning and re-oiling kit, part number HPR4820, to maintain your filter’s condition.

Product Features:

Designed to be superior to stock paper filters
Comes pre-oiled
Designed for an easy installation with OE fit
Made with pre-dyed media for lasting color

from

$43.99

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

Designed to prevent starter overheat due to extreme exhaust temperature
Heat resistant material sandwiched between 2 aluminum plates
Protects Starter From High Temperatures
Made Of 2 Sheets Of Aluminum Heat Resistant Center
Natural Finish

from

$134.99

Give your vintage vehicle’s exhaust system an upgrade with a DynoMax? dual header kit. Designed to attach to headers, it features a special reducer that allows for a variety of mounting options.

Product Features:

COMPATIBILITY — Designed for a variety of full-size 1973-89 GMC 4WD trucks and Chevrolet 4WD SUVs; see product information for compatibility and engine spec
BUILD IT YOURSELF — Design and custom fabricate your own exhaust system with this kit that attaches to OE headers
FLEXIBLE MOUNTING — Special reducer design allows for a variety of mounting options
IMPROVED FLOW CAPACITY — Smooth bends improve flow capacity over traditional bends
SPECS — Extra-long tailpipes with side exits with a full 2.25-in. diameter; tail pipes exit each side of vehicle behind rear tires
COMPLETE SOLUTION — Includes all the necessary clamps, hangers, flanges, gaskets, mounting hardware, intermediate, extension and tail pipes
PREMIUM MATERIALS — Made from quality aluminized steel for durability and long life
PREMIUM MATERIALSÿ–ÿMade from quality aluminized steel for durability and long life
BETTER TOGETHER — Complete your system with premium DynoMax mufflers and DynoMax accessories for a complete performance exhaust system
WARNING — Not legal for use on pollution-controlled motor vehicles; headers are for racing use only and not intended or applicable for highway use

from

$499.99

Product Features:

Fuel Economy From The Engine
Leak Test For Max Performance
Ceramic Headers
Rust And Corrosion Resistance
Mandrel-Formed Power Plenum
Leakproof O-Ringed Port Seals
Include All Mounting Hardware

from

$153.99

The B&M Transpak has all the features in the Shift Improver Kit, plus it provides additional driver manual control. Retain full automatic features and standard shift points with selector in Drive.

Product Features:

Recalibrate Auto. Transmission
Optimum Performance
Select Your App. Mode
Improves Transmission Life
Trans. Removal Not Required

from

$329.99

This fully polished, finned aluminum oil pan is die-cast for a perfect fit. 5 quart capacity. Drain plug & bolts included.

Product Features:

Die Cast Aluminum w/ Finned Bottom
Polished
Includes Drain Plug and Mounting Bolts
5 Quart Capacity

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$165.99

Product Features:

Re-Engineered to Handle High Horsepower
Outlasts Rubber
Virtually Indestructible

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$10.49

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

Internally battled
High-porosity filter
Ideal for high performance
Includes rubber grommet

from

$594.99

The Chevrolet HEI distributor is a favorite for muscle cars, street rods and even circle track racers. The integrated coil keeps under mount wiring clean, and for race cars, the idea of running one wire to the distributor keeps things simple. However, when it comes to performance, the stock HEI falls short. MSD answers the need for a strong, accurate and high performance HEI with our Pro-Billet HEI. The distributor is supplied with our digital HEI module and coil so there is plenty of spark energy combined with improved dwell and timing control. Tig welded on top of the distributor shaft is MSD’s adjustable centrifugal advance assembly. Three sets of springs and four stop bushings let you dial in up to 24 different timing curves to match your driving needs. Plus, there’s a vacuum advance for those concerned with economy. All of this is assembled around a precision and great looking CNC machined housing.

Product Features:

Complete performance HEI distributor upgrade for Chevy V8 engines
Supplied w/Brass Terminal Distributor Cap And Rotor
Full Spark Energy Output To 9000 Rpm
An 8.5 amp; single spark; inductive discharge ignition module
Includes MSD PN[83647] and MSD HEI Coil PN[8225]
Special oil tract improves lubrication to the dist./cam gear
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate

from

$203.99

Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:

7.25 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$7.99

Spectre’s Harmonic Balancer Bolt Kit is designed to fit Chevrolet Small Block 265-400 V8 engines. This grade 8 bolt is 2-1/2 inches long, and features a plated finish for corrosion resistance. This kit also includes a security lock washer.

Product Features:

Fits Chevrolet Small Block 265-400 V8 engines
Features a corrosion resistant plated finish
Gold iridite finish
Grade 8 bolt, 7/16 inch-20 by 2-1/2 inches
Includes security lock washer

from

$42.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use

from

$100.99

Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:

10-15% More Energy
Direct Plug In Replacement Direct OE Fit
Advanced Bobbin Technology
Highly Specialized Silicone Magnetic Steel Cores
Standard Motor Products SMP Dr-31
MSD 8225

from

$213.99

Product Features:

GM 10BL 8.25 REV. R/P 4.11 MGP

from

$429.99

Torque Converter – Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) APPLICATION: Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) The Tork Master is B&M’s lowest cost pe

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$45.99

Spectre Air Cleaner Tops are heavy gauge chrome-plated replacement lids for single and dual stud Chevy/GM air cleaners. This lid is designed to fit the dual stud 15-1/2 inch air cleaner assembly on 1993 and later Chevy/GMC Small block V8 pickups. Featuring a bonded rubber ring to ensure a tight seal, this OEM replacement is manufactured using high quality materials and engineered for optimum fit and function.

Product Features:

Heavy gauge steel construction
Fits 15-1/2 inch air cleaner assemblies with a dual stud
Features a bonded rubber ring
Dual stud OEM replacement
Triple chrome-plated finish

from

$251.99

Designed to reduce wheel shimmy and end vibration caused by larger tires, the Rancho® steering stabilizer kit cuts down on steering arm fatigue to improve handling. The kit includes two Rancho RS5000® steering stabilizers and installation brackets.

Product Features:

COMPATIBILITY — Designed for a variety of trucks and SUVs from Chevrolet®, GMC®, Ford®, Dodge®, Jeep® and Plymouth®
IMPROVED HANDLING AND PERFORMANCE — Reduces wheel shimmy, bump steer and vibration which helps minimize on- or off-road driver fatigue
ACCOMMODATES LARGER TIRES — Engineered for vehicles with oversized wheels and tires.
ENGINEERED TO LAST — Features protective boot to shield shock rod and oil seal and 0.25-in. high-strength, low-alloy steel bracket construction for long life
EASY TO INSTALL — Includes one Rancho RS5000® steering stabilizer and brackets that bolt directly to factory steering linkage with included mounting hardware, no modifications needed
RESISTS CORROSION — Durable black powder-coated and/or zinc-plated brackets resist rust and corrosion
PRECISION DESIGN — Brackets are CNC cut and bent to exact specifications for a perfect fit

from

$14.99

Spectre’s Valve Cover Hold Downs feature high quality steel construction with a triple chrome-plated finish. Manufactured for an optimum fit, this product’s hex heads include a decorative O-ring cap for a customizable appearance to suit your needs. Sold 4 per package, these studs are intended to fit standard height Chevy Center bolt valve covers.

Product Features:

4 bolts included in each package
Allen head includes decorative O-ring cap
Triple chrome-plated finish
Fits standard height Chevy Center bolt valve covers

from

$187.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955 to 1985 400ci small block Chevy V8 engines (externally balanced) with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$349.99

K&N air intake systems are engineered for increased performance, outstanding durability, and sleek aesthetics – and are available in an assortment of finishes and powder coatings. K&N’s state-of-the-art High-Flow Air Filter helps to shield your engine from contaminants, while a meticulously engineered aerodynamic tube design contributes to a guaranteed increase in horsepower and torque. K&N air intake systems are designed to improve acceleration, towing, and throttle response while providing world class protection for your engine. Our intakes are dyno-tested and provide up to 50% more airflow compared to OEM intake systems. K&N intakes are easy to install and maintain with air filter cleaning required only every 100,000 miles.

Product Features:

GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
IMPROVED ENGINE SOUND: Hear the power under the hood.
WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
HIGH QUALITY: Made in America.

from

$631.99

For 3500 to 7500 PRM. Use where low-end torque is not a prime factor. Great for engines with slightly modified heads. HEI ignition will not clear manifold. Street machines, street rods, pro-street and marine.

Product Features:

For 3500 to 7500 RPM
Use Where Low-End Torque is Not a Prime Factor
Great For Engines w/Slightly Modified Heads
Top Has Vacuum Outlet for Power Brakes
Will Accept Forward and Sideways Mounted Carbs
Carburetor Center-to-Center Dimensions 8.875 in
HEI Ignition Will Not Clear Manifold
For Street Mach.; Street Rods; Pro-Street; Marine

from

$143.99

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features: