1995 GMC C1500 Pickup Drivetrains

Below you will find various in-demand GMC Drivetrains, components and accessories for your 1995 C1500 Pickup. Advance Auto Parts has popular C1500 Pickup parts like Universal Joints, 4WD Components, Transfer Cases and more. You’ll also find aftermarket and OEM Drivetrains for other C1500 Pickup model years. Select a category of 1995 GMC C1500 Pickup Drivetrains below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1995 GMC C1500 Pickup Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

Differential Pinion Yokes

Pinion Shaft Bearings

U-Joints

Rear Differential Cover Gaskets

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Drive and Prop Shaft Assemblies

Differential Bearings

Differential Axle Shafts

Bearing Pullers

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

U-Joint Centering Yokes

Differential Cover Bolts

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Cover Plugs

Differential Clutch Packs

Rear Axle Shaft Bearings

Differential Ring and Pinions

Differential End Yokes

Spindle Lock Nuts

Drive Shaft Repair Kits

Differential Lock Assemblies

Axle Spindles

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Rear Housing Cover Gaskets

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Axle Shaft Lock C-Clips

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Differential Carrier Bearing Shims

Input Shaft Seals

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Differential Side Gear Thrust Washers

Differential Pinion Gear Thrust Washers

Transfer Case Shift Fork Inserts

Differential Ring and Pinion Kits

Drive Axle Assemblies

Limited Slip Differential Assemblies

Differential Spider and Pinion Gear Kits

4WD Actuator Connectors

Universal Joint Strap Bolts

Differential Clutch Pack Clips

Axle Differential Bearing and Race Set

Essential Drivetrains for 1995 GMC C1500 Pickups

from

$74.99

Chrome cover for 8.6″, 8.5″ and 8.2″ GM rear.

Product Features:

Fits GM 8.2″, 8.5″ and 8.6″
Chrome

from

$208.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits GM 8.5″ rear with aftermarket positraction
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$16.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$6.79

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$373.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
14 piece kit
Composite clutches

from

$77.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$32.99

Standard open and Gov-Loc cross pin for 9.5″ GM.

Product Features:

Cross pin shaft
Fits GM 9.5″

from

$323.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$503.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$23.99

7.5″ and 8.5″ GM rear U/joint strap, Mech 3R.

Product Features:

u-joint strap
Fits GM 7.5″, 7.625″ and 8.5″
Mechanics 3R u-joint size
One single strap

from

$352.99

Yukon positraction internals for 8.5″ GM with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects. This kit is compatible with Yukon Dura Grip or Eaton positractions. It will not fit a factory Gov-Loc positraction.

Product Features:

Spider gear kit
Fits GM GM 8.5″ and 8.6″ Dura Grip positraction with 30 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and side gear thrust washers.

from

$7.79

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$551.99

If you’re repairing or rebuilding a front or rear differential and want the best performance and longevity from the bearings being replaced, choose this premium differential kit. It includes high-precision bearings manufactured to tighter tolerances and engineered to last longer than common lower-grade bearings that have more backlash when subjected to the torque generated within the differential. This convenient kit also saves the time needed to source individual components. Check the product attributes and fitment details to select the correct premium differential kit for your application.

Product Features:

Ideal solution – this premium differential bearing kit features high-precision bearings to help ensure longer bearing life, prevent backlash, and restore proper differential operation
Direct replacement – the components in this all-in-one kit are engineered to precisely match the fit and function of the original equipment bearings for a seamless installation
Increased reliability – the premium bearings in this kit are manufactured to exacting tolerances and specifications from high quality materials to help ensure optimal performance
Application-specific – check the product attributes and fitment details to choose the correct kit for your application

from

$153.99

Product Features:

GM10 BOLT 8.5″ 30 SPL INTERNAL KIT 1988-1999 (OPEN)

from

$13.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$15.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$6.99

This drive axle shaft lock C-clip is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this drive axle shaft lock C-clip matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$9.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Product constructed to meet all design and operating characteristics as intended by the manufacturer.
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$49.99

This drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$135.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

KIT BRG & SEAL GM 10 BOLT MASTER NON IFS FRONT / REAR

from

$5.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$215.99

Bearing race driver for rear GM 9.5″, 9.25″ IFS, and Ford 9″ HD. (TK HM804810). No return.

Product Features:

Bearing race driver
Fits HM804810 race
All steel construction

from

$52.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1559TV axle bearing and seal kit, TorringtonBrand, 2.530″ OD, 1.620″ ID This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.530″ O.D.
1.620″ I.D.

from

$42.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$179.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

Upgrade your 1995 GMC C1500 Pickup with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1995 GMC C1500 Pickup, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your GMC or enhancing its overall performance, Drivetrains are key to keeping your C1500 Pickup functioning at its best. At Advance Auto Parts, we offer a wide selection of 369 Drivetrains for the 1995 GMC C1500 Pickup, designed to meet your needs without breaking the bank. From Universal Joint replacements to 4WD Components upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1995 GMC C1500 Pickup at great prices. Our Drivetrains inventory for this model ranges from just $2.99 to $2,304.99, with an average price of $276.11. Our 369 Drivetrains in stock come from 21 trusted brands, so you’re sure to find the right part for your 1995 GMC C1500 Pickup without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1995 GMC C1500 Pickup, we stock popular OEM and aftermarket Drivetrains from top names like National, DriveWorks, Motive Gear, and more. National Drivetrains start at just $7.99 and boast an impressive 4.3 stars average rating from customers. DriveWorks and Motive Gear also bring quality to the table, with Drivetrains available starting at $7.99, and at an average 4.3 stars rating. With 1,211 customer reviews and counting, our 1995 GMC C1500 Pickup Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1995 GMC C1500 Pickup is always ready to roll. We’re committed to providing you with everything you need to keep your C1500 Pickup in top shape, all in one place. Start shopping confidently below for your 1995 GMC C1500 Pickup!

Best-Selling Universal Joints for 1995 GMC C1500 Pickups

Enhance the driving experience in your GMC with 46 quality Universal Joint components, starting at $8.49.

show more show less

from

$42.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$15.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 330, 330A, 331 & 331A
Contains two 1.66″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws

from

$34.99

Product Features:

INHIBITS GALVANIC REACTION – Designed specifically for aluminum yokes to avoid a galvanic reaction that leads to corrosion
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
CORROSION PROTECTION – Bearing cups and snap rings are chemically-coated to protect aluminum yokes
KEEPS DIRT OUT – Nitrile rubber grease seals with double lip design protects components from wear-causing contaminants
GREASABLE DESIGN – Radial design of bearing cups allows 360 Degrees lubricant distribution to all bearing surfaces to flush out contaminants and moisture to reduce corrosion and wear
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$45.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$34.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$42.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$15.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging to provide higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting allows for easy maintenance and the flexible use of the entire assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals are applied to optimize grease retention and reduce contamination

from

$31.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$11.99

For U-Joints 355, 372 & 534G
Contains two 1.81″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws

from

$29.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$29.49

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$26.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$34.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$37.99

Product Features:

INHIBITS GALVANIC REACTION – Designed specifically for aluminum yokes to avoid a galvanic reaction that leads to corrosion
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
CORROSION PROTECTION – Bearing cups and snap rings are chemically-coated to protect aluminum yokes
KEEPS DIRT OUT – Nitrile rubber grease seals with double lip design protects components from wear-causing contaminants
GREASABLE DESIGN – Radial design of bearing cups allows 360 Degrees lubricant distribution to all bearing surfaces to flush out contaminants and moisture to reduce corrosion and wear
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$45.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$37.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$19.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$42.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$37.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$41.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$36.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

Top Picks for 1995 GMC C1500 Pickup Transfer Cases

Upgrade GMC C1500 Pickups with top-quality Transfer Cases parts, including 6 OEM and aftermarket selections for your 1995 model.

show more show less

from

$5.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$11.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$14.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; single-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$77.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$19.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$11.99

Shift Fork Insert

In-Demand Drive Shafts and Axles for 1995 GMC C1500 Pickups

Select from 45 premium Drive Shafts and Axles parts for your 1995 GMC C1500 Pickup, with prices ranging from $5.29 to $1,608.99.

show more show less

from

$13.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$40.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.48 INCH / 63 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
NOT PICTURED: TWO DUST SHIELDS

from

$46.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$6.99

Direct replacement – this drive axle shaft lock C-clip matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$44.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$73.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$45.99

from

$44.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$21.49

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 INCH / 35 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
COMPLETE MOUNT

from

$31.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$19.99

Value-priced bearing meets all cataloged application requirements.

from

$29.49

Drive Shaft Center Support

from

$19.79

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$52.99

Includes axle bearing and seal
Services one side
Torrington Brand
2.530″ O.D.
1.620″ I.D.

from

$8.99

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
.150″ thick

from

$24.99

Product Features:

Fits GM 8.6″ and 9.5″
Sleeve to adapt standard yoke to use late model triple lip pinion seal

from

$89.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. axle bearing and seal kit for C10 Aero truck, 2.800″ OD, 1.620″ ID. This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
2.800″ O.D.
1.620″ I.D.

from

$38.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 60-02; DODGE 64-66; FORD 75-15; GMC 60-02;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1960-2015
Weight approx: 3 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
NO STUDS

from

$7.99

Axle seal, for 1559 OR 6408 bearing, NOT COARSE spline 12T.Yukon Mighty seal.

Product Features:

Rear axle seal
2.530″ O.D.

from

$13.49

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 58-02; GMC 55-02; INTL 57-02;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2002
Weight approx: 2 Lbs
BEARING ID / BORE: 1.1811 INCH / 30 MM
CENTERLINE: 3.50 INCH / 89 MM
MOUNT WIDTH: 1.50 INCH / 38 MM
COMPLETE MOUNT

from

$21.99

Axle seal for 9.5″ GM.Yukon Mighty seal.

Product Features:

Rear axle seal
Fits GM 9.5″

from

$11.99

Axle seal for ’88 and newer GM 8.5″ Chevy C10.Yukon Mighty seal.

Product Features:

Rear axle seal
Fits 1988 and up GM half ton truck
2.800″ O.D.
1.620″ I.D.

from

$10.99

9.5″ GM C/clip.

Product Features:

c-clip for GM 9.5″

Most Sold 1995 GMC C1500 Pickup Differentials

Explore our best-selling GMC parts for the 1995 C1500 Pickup among 269 OEM and aftermarket options starting from $2.99.

show more show less

from

$14.49

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$7.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$63.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$9.29

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$7.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$7.99

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$503.99

from

$37.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$153.99

Product Features:

GM10 BOLT 8.5″ 30 SPL INTERNAL KIT 1988-1999 (OPEN)

from

$234.99

Product Features:

GM 10BL 8.5 R/P 3.42A MG FRT/REAR

from

$10.99

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$26.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$8.99

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$53.99

Product Features:

STRONG AND DURABLE – Controlled heat treatment process for strength and durability
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for durability and performance
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
Professional technicians know they can depend on National

from

$7.79

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$241.99

Product Features:

GM 10BL 8.5 R/P 3.73A MG FRT/REAR

from

$16.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$6.79

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$139.99

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$37.99

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$243.99

Product Features:

GM 10BL 8.5 R/P 3.73 MG FRT/REAR

from

$156.99

Product Features:

KIT BRG&SL GM 8.5″ 10 BLT MSTR NON IFS FRONT / REAR

from

$135.99

KIT BRG & SEAL GM 10 BOLT MASTER NON IFS FRONT / REAR

from

$342.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Top-Rated Drivetrains Brands For Your 1995 GMC C1500 Pickup

Shop for the best-rated brands offering Drivetrains and other products for your 1995 GMC C1500 Pickups. Below you’ll find some of our best rated Drivetrains from National, DriveWorks, and Motive Gear, and more. Drivetrains from these brands that fit a 1995 C1500 Pickup start at just $7.99 and are rated as high as 4.3 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular National 1995 GMC C1500 Pickup Drivetrains

When it comes to maintaining or upgrading your 1995 GMC C1500 Pickup, using quality Drivetrains is essential to ensure durability and a perfect fit. National ticks all of those boxes. We offer a wide selection of National Drivetrains, specifically designed for the 1995 GMC C1500 Pickup. With over 3 National brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $7.99, with an average price of just $10.42. Plus, with over 15 customer reviews and an average rating of 4.3 stars, you can trust that our National Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $7.99

(4)

Bearing Race

“Goes with M88010 bearing cup. Application was the pinion bearing race for a Ford 9 Inch on a 1957 Ford F-100.”

from $13.99

(9)

Bearing

“as advertised”

from $9.29

(2)

Bearing Race

“Reasonable price and woks well. front diff 2006 Escalade esv”

Popular DriveWorks 1995 GMC C1500 Pickup Drivetrains

DriveWorks auto parts is one of the highest quality Drivetrain brands in the market. Any 1995 GMC C1500 Pickup owner should feel confident when installing genuine DriveWorks parts in their vehicle. To ensure the best fit and performance for your 1995 C1500 Pickup, Advance Auto Parts carries a full inventory of 3 DriveWorks Drivetrains. Plus you will be keeping your GMC in peak condition while saving money because prices on these DriveWorks Drivetrains range from $7.99 to $15.99, plus, with more than 54 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $15.99

(52)

Universal Joint

“Perfect fit.”

from $7.99

(1)

Oil Seal

“Didn’t fit my 1992 K1500 10 bolt 8.5″ ring gear rear end. Was told wrong part.”

from $15.99

(1)

Universal Joint

“Exact fit and worked perfectly”

FAQs for 1995 GMC C1500 Pickup Drivetrains

Which Drivetrains are best-sellers for 1995 GMC C1500 Pickups?

Out of 369 Drivetrains that fit 1995 GMC C1500 Pickups, the following parts are the top sellers:

DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (12079201) – $14.49
Axle Housing Cover Gasket Oval Shaped 10 Bolt Hole Gasket (5185823) – $10.99
DEX/MERC ATF Conventional Automatic Transmission Fluid, 1 Quart (12079139) – $11.99

What’s the price range for 1995 GMC C1500 Pickup Drivetrains?

Drivetrain prices for the 1995 GMC C1500 Pickup start at $2.99 and go up to $2,304.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1995 GMC C1500 Pickup?

The average price for Drivetrains for the 1995 GMC C1500 Pickup is $276.11. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

What are the cheapest Drivetrains for my 1995 GMC C1500 Pickup?

The cheapest 1995 GMC C1500 Pickup Drivetrains we carry in stock are:

Ring Gear Bolt (20520168) – $2.99
Differential Crush Sleeve (20520169) – $2.99
Differential Cross Shaft (10282201) – $2.99
Differential Ring Gear Bolt (10282159) – $2.99
Differential Crush Sleeve (10282146) – $2.99

What are the top-rated Drivetrains that fit the 1995 GMC C1500 Pickup?

Out of 1,211 reviews by customers, our 1995 GMC C1500 Pickup Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1995 GMC C1500 Pickup and their top-rated products:

Universal Joints
- Greaseable Premium Universal Joint (10087268) – $34.99
- Universal Joint, Greaseable S44 To 1330 Series (10841133) – $45.99
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99

What types of Drivetrains do you sell for my 1995 GMC C1500 Pickup?

As of 11/2/25, these are some of the most in-demand types of Drivetrains for a 1995 GMC C1500 Pickup:

Can I get help with 1995 GMC C1500 Pickup Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about GMC Drivetrains and more.

What is your return policy for GMC C1500 Pickup Drivetrains?

Advance Auto Parts keeps returns simple. For new GMC C1500 Pickup Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1995 GMC C1500 Pickup Drivetrains

Yukon Gear – Chrome Cover For 8.6", 8.5" And 8.2" GM Rear (Part No.32017)

USA Standard Gear – Master Overhaul Kit for the GM 8.5 Differential with HD Posi or Locker (Part No.37057)

National – Multi-Purpose Bearing (Part No.A-5)

Dorman – Help – Differential Shaft Lock Bolt (Part No.81048)

Yukon Gear – 14 Plate Duragrip Composite Clutches For GM 8.2", GM 8.5", 12T, 12P, Ford 8.8" & Cast Iron ‘Vette (Part No.16064)

National – Multi-Purpose Bearing (Part No.307-FFL5)

Yukon Gear – Standard Open And Gov-Loc Cross Pin For 9.5" GM (Part No.33402)

Dorman – Differential Pinion Yoke Assembly (Part No.697-531)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)

Powertrax – Grip LS Traction System (Part No.LS201030)

Yukon Gear – 7.5" And 8.5" GM Rear U/Joint Strap, Mech 3R (Part No.41201)

Yukon Gear – Positraction Internals For 8.5" GM With 30 Spline Axles (Part No.16053)

National – Bearing Race (Part No.LM102910)

Dorman – Premium Ring and Pinion Master Bearing and Installation Kit (Part No.797-115)

Motive Gear – Differential Carrier Gear Kit (Part No.GM10BI-30)

National – Bearing (Part No.M88048)

National – Bearing Race (Part No.HM88610)

Yukon Gear – The Carrier Bearing Puller (Part No.56072)

Dorman – Help – Axle Shaft Lock Assortment (Part No.81050)

Carquest Premium – Multi-Use Connector (Part No.PTA1271)

Dorman – Drive Shaft Repair Kit – Only Fits Dorman Driveshafts (Part No.932-984)

Motive Gear – Differential Master Bearing Kit – Timken (Part No.R10RMKT)

Driveworks – Oil Seal (Part No.S-9449)

Yukon Gear – Bearing Race Driver (Part No.56012)

Yukon Gear – R1559Tv Rear Axle Bearing And Seal Kit (Part No.10001)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.270)

Pro-King – Differential Internal Nest Kit (Part No.742G717A)

Spicer – Universal Joint, Greaseable 1330 Series OSR (Part No.5-213X)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.492-10)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354C)

Spicer – Universal Joint, Greaseable S44 To 1330 Series (Part No.5-212X)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.534G)

Driveworks – Universal Joint (Part No.DW-534G)

Driveworks – Universal Joint (Part No.DW-354)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.530-10)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.254)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.234)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.355)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.290)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.355C)

Spicer – Universal Joint (Part No.5-795X)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.232)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.235)

Driveworks – Universal Joint (Part No.DW-331)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.270)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.231)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.331)

Spicer – Universal Joint, Greaseable S44/3R Series (Part No.5-3147X)

Driveworks – Universal Joint (Part No.DW-355)

Driveworks – Universal Joint (Part No.DW-235)

Carquest Premium – Multi-Use Connector (Part No.PTA1271)

Driveworks – Oil Seal (Part No.S-9449)

Driveworks – Taper Bearing Cone (Part No.S-M-88048)

National – Multi-Purpose Seal (Part No.4529N)

National – Multi-Purpose Bearing (Part No.307-FFL5)

Driveworks – Taper Bearing Cone (Part No.S-HM-88649)

USA Standard Gear – Shift Fork Insert (Part No.71380)

National – Bearing (Part No.M88048)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)

National – Drive Shaft Center Support Bearing (Part No.HB-206-FF)

Driveworks – Universal Joint (Part No.DW-331BL)

Dorman – Help – Axle Shaft Lock Assortment (Part No.81050)

Spicer – Universal Joint, Greaseable 1350 Series (Part No.5-178X)

National – Drive Shaft Center Support Bearing (Part No.HB-88508-A)

Spicer – Universal Joint (Part No.5-1350X)

National – Drive Shaft Center Support Bearing (Part No.HB-88107-A)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)

Driveworks – Cylindrical Bearing (Part No.S-R1561TV)

Driveworks – Ball Bearing (Part No.S-HB-88107-A)

Driveworks – Drive Shaft Center Support (Part No.S-HB-88508-A)

National – Tapered Roller Bearing Cone (Part No.HM88649)

Yukon Gear – R1559Tv Rear Axle Bearing And Seal Kit (Part No.10001)

Yukon Gear – C/Clip (Part No.33083)

Yukon Gear – Adapter Sleeve Fro GM 8.6" & 9.5" Yokes To Use Triple Lip Pinion Seal (Part No.41150)

Yukon Gear – GM 7.5"/8.0"/8.5"/8.6" Rear Axle Bearing And Seal Kit (Part No.10005)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6053)

Yukon Gear – Axle Seal, For 1559 Or 6408 Bearing (Part No.30201)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6035)