from

$788.99

Dual Valve Springs from COMP Cams are manufactured from Super Clean wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter what the application. The dual spring design creates a stronger valve spring that can easily handle the increased lift found in extreme stress applications. COMP Cams Dual Valve Springs exceed the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 112 lbs. @ 1.900″, Open Pressure: 355 lbs. @ 1.200″
O.D.: 1.509″, I.D.: 0.697″
Dual valve springs with damper

from

$439.99

The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:

Universal Floor Mount Application
Base Trimmed For Custom Fit
Cable Operated
Quick Installation
Accurate Shifting

from

$49.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$60.99

MSD Ignition is a company built on Customer Satisfaction and Service. That is why all of MSD products go through regimented test procedures before they are ever packaged and shipped. MSD stands behind its products for one full year after purchase

Product Features:

Rotor phasing can be adjusted.
Ideal When Atomic TBI Is Controlling The Timing

from

$664.99

MSD’s Ready-to-Run Ford distributors are the perfect upgrade for bulky Duraspark systems or ancient breaker point models. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance. The billet aluminum housings of these distributors are 5/8 In. smaller in diameter to accommodate induction setups and tight engine compartments. A maintenance-free magnetic pick-up is responsible for triggering the high voltage sparks while a sealed ball bearing guides an oversized shaft. Beneath the bolt down cap and MSD race rotor you’ll find MSD’s accurate mechanical advance assembly. Different advance springs and stop bushings are supplied so you can easily tune a curve to match your needs. Plus, there is a vacuum advance canister to increase economy on long drives.

Product Features:

Equipped w/Steel Gear
CARB E.O. Approved
Does not require an MSD Ignition Control
Supplied w/small dia. cap w/HEI style terminals; race and rotor
Will accept PN[8441] Cap-A-Dapt
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate
Mech. advance assem. can be locked out for crank trigger systems

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$112.99

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

8.8mm Graphite Suppression
Silicone Spark Plug Boots
550 Degree Double Silicone Construction
Fiberglass Braid
Carbon/Graphite Core
Magnetic Suppression
Fiberglass/Kevlar Core
500 Ohms Resistance

from

$54.39

MSD Ignition control are easy to install, but we also offer several plug-in harnesses. These are especially handy for quick installation on late model vehicles! The harnesses plug directly into your factory coil and harness then four color coded wires plug into the corresponding wires of the MSD. Two wires go from the MSD to the battery and you’re done with no cutting or splicing!

Product Features:

Splice free installation
Plugs directly into factory coil

from

$368.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$28.99

Available in kits including front cover gasket, crankshaft seal, fuel pump and water pump gasket or including cover gasket and front seal.

Product Features:

Timing Cover Gasket And Oil Seal Kit

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$85.99

The Edelbrock #4463 Signature Series Valve Covers are designed for Ford 429/460 V8 applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:

Big Block Ford 428-460
Short
Chrome Steel
Set Of Two
Rubber Grommets For Breather

from

$163.99

Flywheels

from

$379.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$210.99

Product Features:

Designed for 1500 to 7000 Performance
Large Plenum
Long Tapered Runners
90mm. Throttle Body Opening
Polished Finish

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$43.99

Super Intake Manifold Bolts

from

$30.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$54.99

Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:

Fits Ford 429 – 460 engines
Has a 3/8 inch NPT threaded hole for temperature sensor
Includes sealing O-ring
Chrome plated
Easy to install
Hardware not included

from

$190.99

Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

Product Features:

7.7 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$60.29

Mr. Gasket CopperSEAL Header Gaskets are a high quality copper gasket that performs extremely well and are reusable. We recommend this in all racing and high performance applications. They are for stock heads unless indicated, and work well in high heat and turbocharged applications.

Product Features:

Manufactured from ¿Dead Soft¿ (solid) .043″ thick copper material
Manufactured from ┐Dead Soft┐ (solid) .043″ thick copper material
.051″ embossment around each exhaust port to seal irregular surfaces. Total gasket thickness .094″
Provides excellent sealing and durability
Conforms to and seals minor surface irregularities
For high performance street, drag race, oval track and turbocharged (extreme heat) applications

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$284.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$132.99

The Monro-Magnum® steering stabilizer stops vibration before it gets to the driver. Acting as a horizontal shock absorber, Monro-Magnum® steering stabilizers help reduce vibrations that travel through the steering system to the driver.

Product Features:

1/2 inch Piston Rod Heavy-duty nitrocarburized rod for long service life
All Weather Fluid Contains special modifiers to reduce friction and ensure smooth rod reaction.
Full Displaced Valving Better valving range on both the compression and extension cycles of the unit for a smooth comfortable ride.
Micro-Cellular Gas Design Allows unit to be mounted horizontally.
Sintered Iron Piston Stronger than traditional metals, enhances durability for longer service life.
Special Seal ‘Self-lubricating’ fluid seal designed to retain gas without excessive wear or friction.

from

$438.99

Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

Mount Can Be Clocked To Assist In Mounting
Downsized design helps clearance issues w/oil pans and exhaust
Ball bearing supported armature and pinion gear
3 Hp Motor Provides Power For High Compression Engines
Gear reduction of 4.4:1 improves torque for great cranking

from

$58.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$299.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal
Available in Multiple Finishes

from

$87.19

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features: