1995 Chevrolet G30 Differentials

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Polished aluminum replacement cover for Dana 80.

Product Features:

• Fits Dana Spicer 80
• Finned polished aluminum

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM807010 race
• All steel construction

Differential

8.5, 9.5, & 8.2 Buick, Oldsmobile, Pontiac GM REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Pinion Redi-sleeve
• Fits GM 8.5″, 9.5″ and 8.2″ Buick, Oldsmobile and Pontiac

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features:

• AXLE SHAFT 10.5″ 30 SPL. 37 9/16″ R.H.

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 1988 and down GM 10.5″ 14 bolt truck
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 70U
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

DiffrlPinSupportBolt

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: spring loaded; multi-lip
• Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
• Resistance to EP lubricants
• Low swell in hydrocarbon fluids
• Delivers quality and reliable performance for every type of repair

Yukon 1480 Lifetime Series U/Joint. 4.188″ snap ring span, 1.375″ cap diameter. Outside snap ring.

Product Features:

• Clutch kit
• Fits GM 10.5″ 14 bolt truck with Eaton positraction
• Carbon fiber clutches

14T cover gasket.

Product Features:

• Cover gasket
• Fits GM 10.5″ 14 bolt truck

Product Features:

• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Dana 70 & Dana 80 standard Open cross pin shaft, one piece case.

Product Features:

• Cross pin shaft
• Fits Dana Spicer 70 and 80

Yukon replacement yoke for Dana 60 and 70 with 1410 U/joint size. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring.This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 60, 70, 70U and 70HD
• 29 spline
• 1410 u-joint size
• 4.188″ snap ring span
• 1.188″ cap diameter
• Outside snap ring design
• U-bolt style

Product Features:

• D70 BEARING SEAL & GASKET M/K

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

Product Features:

• DANA-60 R/P 3.54 STD MG 24813-5X (USES PRE-LOAD SHIMS)

14T pinion gear Thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits GM 10.5″ 14 bolt truck

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Product Features:

• Powertrax® proves that you don’t have to choose between the superior traction of a locking differential and smooth handling and drivability of an open differential. Powertrax Lock-Right Lockers, No-Slip Traction Systems and GRIP limited slip differentials and lockers give you the best of both worlds!
• The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
• Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
• Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
• Powertrax® = Extreme Traction Systems!

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• CARRIER BEARING KIT FRD 10.5″ W/TIM

Product Features:

• Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

Yukon replacement standard open carrier case for Dana 60, 4.10 & down Semi-Float & Full float, (incl ABS) 2-1/8″ tall.

Product Features:

• Standard open carrier case
• Fits Dana Spicer 60
• 4.10 and down ratio only
• Does not include spider gears

Yukon positraction internals for 9.5″ GM with 33 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects. These internals are for Eaton positractions only. They will not fit factory positractions.

Product Features:

• Spider gear kit
• Fits GM 9.5″ with Eaton positraction
• Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.