1995 Chevrolet Corvette Performance and Racing Products
More 1995 Chevrolet Corvette Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1995 Chevrolet Corvette, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1995 Chevrolet Corvette Performance and Racing Products
Energy Suspension – Tie Rod Dust Boot (Part No.9.13102G)
from
$5.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Mr. Gasket – Exhaust Gasket Set (Part No.150A)
from
$25.99
Mr. Gasket has three types of exhaust gaskets–standard, Ultra Seal, and Copperseal. Use the standard for a stock rebuild and the Ultra or Copperseal for extra blowout protection.
Product Features:
See More
Product Features:
- High-temperature exhaust material
- Withstands extreme exhaust heat
- Provides excellent sealing and durability
- Superior tensile strength
- Resists deteriorating
- Provides excellent torque retention
Edelbrock – Performer; Cylinder Head (Part No.60469)
from
$569.99Product Features:
- Out-of-the-Box Bolt-On Performance
- Designed For Street/High Performance Big Blocks
- Specially Designed Oval Ports
- Increased Flow And Velocity
- Highly Efficient Semi-Open Style Chamber
- High Velocity Short Intake Ports
- Fit GM Mark IV; Gen V; and Gen VI Blocks
- Bare Head Only; Use PN[60479] for Complete
Hypertech – Power Coil Kit for GM HEI Systems with Clamp Down Cap (Part No.4050)
from
$95.99
Hypertech’s Power Coil is capable of firing a street or slightly modified engine up to 7000 RPMs. Voltage gain over stock can exceed up to 57% more output depending on application. Stock coils usually average around 36,000 volts as compared to Hypertech’s coil kits that average between 45,000 and 55,000. Our coil kits include coil, brass terminals, cap, and rotor. Nylon rotor hold-down screws are included to prevent misfire, and our caps are made of high dielectric material to prevent carbon tracking. Each cap fits the distributor housing tightly to eliminate leakage. Power Coil/Caps/Rotors are NOT legal for sale/use in CA.
Product Features:
See More
Product Features:
- High Output Voltage
- More Spark Energy
- Up To 7000 RPMs
- No Drop Off In Power As RPMs Increase
- Wider Plug Gaps; Brass Terminals
- Constructed w/Burn Through Resistant Materials
- Excellent Dielectric Strength
- Resists Carbon Tracking
- Product might not be available in all states due to local laws.
K&N – Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (Part No.E-1650)
from
$89.99
The K&N E-1650 replacement air filter is designed to increase horsepower and acceleration by reducing restriction and increasing air flow to your engine. The E-1650 is made with layers of woven cotton that offer superior filtration and can be washed and reused repeatedly. K&N replacement air filters can go up to 50,000 miles before cleaning is required, depending on driving conditions. The E-1650 is easy to install and is custom designed to fit right into the factory air box of many automotive & industrial applications.
Product Features:
See More
Product Features:
- ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
- RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
- 4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
- CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
- ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
- EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
- ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
- MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability.
Hooker Headers – Super Comp. Header (Part No.2108HKR)
from
$548.99
Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.
Product Features:
See More
Product Features:
- Long Tube Lengths
- Long Transition Collectors
- Monstrous Low-Mid Range Torque
- Keep Top End Horsepower
- Provides Finest Fit
- Most Durable Design Available
MSD Ignition – Trigger Wheel; Flying Magnet; Small Block Chevy (Part No.8611)
from
$245.99
For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.
Product Features:
See More
Product Features:
- Replacement crank trigger wheel for small block Chevy
- Absolutely the most accurate way to trigger the ignition
- The non-magnetic pickup cannot be false triggered
- Powerful magnets are embedded in a billet aluminum trigger wheel
Energy Suspension – Sway Bar Bushing Set (Part No.3.5141G)
from
$30.99
Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.
Product Features:
See More
Product Features:
- Allows Sway Bar System to Work At 100% Efficiency
- Zerk Type Fittings
- Allows for Periodic Greasing
- Lasts Much Longer Than OEM Rubber Bushings
- Handling Characteristics Improve Dramatically
Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.501)
from
$113.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
B & M – Automatic Shifter, StarShifter (Part No.80675)
from
$297.99
Features include NHRA/ IHRA reverse lockout, backup light switch, neutral safety switch, polished T-handle. Cable operated for quick installation and accurate shifting. For 2 and 3 speed applications.
Product Features:
See More
Product Features:
- Base Trims For Custom Fit
- Cable Operated
- Quick Installation
- Accurate Shifting
- NHRA/IHRA Reverse Lockout Meets Requirements
- Includes Neutral Safety Switch
- Polished Aluminum. T-Handle and Cable
FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)
from
$36.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
- Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
- Not intended for use in emission controlled vehicles.
- Not intended for use in emission controlled vehicles.
MagnaFlow – Stainless Cat-Back System Performance Exhaust Kit for Chevrolet Corvette (Part No.15887)
from
$1661.99
If you’re in the market for a replacement exhaust or just want something that offers you a little more power over stock, then look no further than MagnaFlow for your aftermarket exhaust needs. Made of 100% stainless steel and then fully polished to give it that extra shine, our cat-back systems not only perform, but also look good in the process.
See More
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1041)
from
$108.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
- NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
- SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
- STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
Mr. Gasket – GSKT INTAKE (Part No.5812)
from
$46.99
GSKT INTAKE
Energy Suspension – Hyper-Flex System (Part No.3.18123R)
from
$373.99
Product Features:
See More
- Incredible Improvement in Control
- Maintains Proper Caster and Camber Alignment
- Increase in Handling and Control
- Greatly Reduce Wheel Hop on Quick Acceleration
- Even Braking Control is Improved
- Better Suspension Stability
B & M – Holeshot 3600 (Part No.20425)
from
$796.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
- Dual Pattern Drive Lugs
- New Turbine Hub
- New Springs/Rollers In Stator
Energy Suspension – Strut Rod Bushing Set (Part No.3.7108R)
from
$37.99
These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.
Product Features:
See More
Product Features:
- Made from HYPER-Flex Polyurethane
Energy Suspension – Strut Rod Bushing Set (Part No.3.7102R)
from
$51.99
These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.
Product Features:
See More
Product Features:
- Made from HYPER-Flex Polyurethane
Edelbrock – C-66-Dual-Quad; Intake Manifold (Part No.54211)
from
$669.99Product Features:
- Polished PN[5421]Hand-Buffed for Brilliant Shine
- Designed for 1500 to 6000 RPM Performance
- Manifold has a Balanced 180+ Firing Order
- Smooth and Consistent Part-Throttle Power
- Makes +25 HP over Edelbrock Torker II
- Makes +30 ft/lbs of Torque over Performer
- Carburetor Center-to-Center Dimensions = 6-7/16 in
- For Rectangular Port Heads
Edelbrock – Performer Intake Manifold for 1987-95 Small-Block Chevy, Polished Finish (Part No.21041)
from
$627.99
Product Features:
See More
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 Deg Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
- Accepts Late-Model Choke; Waterneck; and HEI
- Accepts A/C And Alternator
- Accepts Exhaust Heated Chokes
Energy Suspension – Control Arm Bushing Set (Part No.3.3145G)
from
$78.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Energy Suspension – Control Arm Bushing Set (Part No.3.3145R)
from
$74.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
PerTronix – D4062 Flame-Thrower HEI Distributor Rotor Blue (Part No.D4062)
from
$15.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provi
Product Features:
See More
Product Features:
- PerTronix D4062 Flame-Thrower HEI Distributor Rotor Blue
- Made from hi-performance 60 KV rated alkyd molding compound.
Mr. Gasket – Distributor Hold-Down Clamp (Part No.1009)
from
$9.99
Add sparkle to your engine with this chromed hold-down clamp. With bolt and gasket. Serrations on the bottom prevent distributor and magneto rotation for accurate timing.
Product Features:
See More
Product Features:
- Rolled Edges For Strength
- Ideal For Magnetos
- Ideal For Ignition Distributor
Earls Performance Product – Brake Bleeder Screws (Part No.280029ERL)
from
$36.99
Brake Bleeder Screws
Hays – Performance; Flexplate (Part No.10-025)
from
$142.99
Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.
Product Features:
See More
Product Features:
- Thicker Than Stock Steel Plate
- Ring Gear Securely Welded
- Dual Bolt Patterns
- Zinc-Dichromate Plated To Resist Corrosion
- Withstands High Torque and RPM
Hays – Performance; Flywheel (Part No.10-140)
from
$374.99
Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.
Product Features:
See More
Product Features:
- Certified Billet Material
- Borg and Beck Clutch Pattern
- Long-Style Clutch Pattern
- Ring Gear Securely Mounted To Prevent Spinning
Hays – Performance; Flexplate (Part No.10-024)
from
$146.99
Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.
Product Features:
See More
Product Features:
- Thicker Than Stock Steel Plate
- Ring Gear Securely Welded
- Dual Bolt Patterns
- Zinc-Dichromate Plated To Resist Corrosion
- Withstands High Torque and RPM
Popular 1995 Chevrolet Corvette Performance and Racing Products Categories
1995 Chevrolet Corvette Performance and Racing Products
You count on your 1995 Chevrolet Corvette to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 51 Performance and Racing Products ranging in price from $5.99 to $811.99, you’re sure to find everything you need for your 1995 Chevrolet Corvette.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 16 different brands like Energy Suspension, MSD Ignition, and FEL-PRO Performance. 1995 Chevrolet Corvette Performance and Racing Products start as low as $5.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 30 extensive product reviews on 1995 Chevrolet Corvette Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Intake Manifold Bolts with 4.6 stars and Automatic Shifter, Unimatic Shifter with 4.3 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1995 Chevrolet Corvette below to get started!
Top-Rated Performance and Racing Products Brands For Your 1995 Chevrolet Corvette
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1995 Chevrolet Corvette running right for years to come. In our inventory you’ll find brands like Energy Suspension, MSD Ignition, FEL-PRO Performance, and even more.
Popular FEL-PRO Performance Performance and Racing Products
You’ll find popular FEL-PRO Performance brand products across Performance Engines. All are waiting to get your 1995 Chevrolet Corvette back on the road. Some of the top-rated FEL-PRO Performance products in these categories are:
from
$36.49
(1)
Lower Intake Manifold Gasket Set: Includes Sealer, 3 Piece Set
Performance Engine Intake Manifold Gaskets
Top-Rated Performance and Racing Products
If are what you’re looking for, our inventory holds plenty. We stock brand Performance and Racing Products for your 1995 Chevrolet Corvette, and some of our most reviewed parts include:
FAQs for 1995 Chevrolet Corvette Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1995 Chevrolet Corvette?
Out of 51 Performance and Racing Products for the 1995 Chevrolet Corvette, the most popular in our inventory are:
What are the top-rated 1995 Chevrolet Corvette Performance and Racing Products?
Top-rated Performance and Racing Products for your 1995 Chevrolet Corvette based on customer reviews/ratings are:
from
$461.99
(1)
Automatic Shifter, Megashifter
“its was pretty easy to install if u have any type of knowlegde of cars it should not be difficult at all and the shifting is awesome just be careful w”
