1994 GMC C1500 Performance Engines

Edelbrock part No: 97384 high performance hydraulic roller lifters for 1987 and later small-block Chevys are the perfect match for Edelbrock Rollin’ Thunder hydraulic roller cams. The Edelbrock Part No: 97384 are a drop-in replacement for 1987 and later blocks that accept factory roller camshafts. These precision hydraulic roller lifters feature tight ID tolerances that allow for better control at higher RPM and a micro finish OD for reduced friction.

Edelbrock Water Pump for Small-Block Chevy in Black Finish (Long), 88113.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Spectre’s Engine Dress-Up Kit was designed for the ’58-’86 Chevrolet small block 265-400. This kit includes: stock height baffled covers, chrome T-bar hold downs, chrome PCV breather, chrome breather, chrome oil filler cap, grommets, and a stainless steel braided PCV hose with red/blue Magna-Clamps. Designed for use with OE specifications for fit and function, Spectre products are engineered to perform as good as they look.

Edelbrock part No: 6997 Front Timing Cover Gasket set for Small-Block Chevy. Includes front cover gasket and front seal.

This Holeshot 3000 is for all 1998-02 GM Camaro/Firebirds, 1999-06 GM1500 trucks/SUV’s with LS1, 4.8L, 5.3L, or 6.0L engine and 4L60E or 4L65E transmission. This converter retains the lock-up feature. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 3000 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. Will Not fit 1997-05 Corvette. Has both 10.75 and 11.08-inch bolt circles

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

These are high quality gaskets that works well on those hard to seal applications. The low density fiber & rubber blend gasket material seals those minor head imperfections with a low clamp force. At .187 inch, the extra thickness can also offer slightly more clearance for roller rockers. Ideal for all those high performance applications where you take the valve covers off and on a lot, and sticking is a problem.brbrFits all 1965-2000 Chevy Big Blocks: 366,396,402,427,454 including GM (General Motors) Gen VI Crate Engines like the 502 and 572.

New Everbright(TM) Manifold coating now available on the most popular Weiand and Holley intakes uses proprietary vacuum metalizing technology combined with a protective clear powdercoat to provide long lasting, virtually maintenance free polished looks.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Spectre’s Harmonic Balancer Bolt Kit is designed to fit Chevrolet Small Block 265-400 V8 engines. This grade 8 bolt is 2-1/2 inches long, and features a plated finish for corrosion resistance. This kit also includes a security lock washer.

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

“Edelbrock part No: 9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise formed wedged ends for a high quality fit with the cup seats. A black oxide finish is added for corrosion resistance. Pushrod Specifications: – For use with Edelbrock hydraulic roller lifters No: 97423 – Outside Diameter: 5/16″” – Length: 7.250″””

“Competition Cams Magnum 7.200″” Long, .080″” Wall, 5/16″” Diameter Pushrod Set, 7608-16. ”

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

HYDRAULIC – Magnum: Street/strip applications. 10:1+ compression, 3000+ stall or 4 speed. 4.10 or lower gears and aftermarket intake. Very rough idle. OR Oval Track: Good for hobby stock in 454 where hydraulic lifters must be used.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers.

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

The Edelbrock No: 7361 head gaskets provide the best sealing solution and are matched to Edelbrock cylinder heads for optimal performance. Edelbrock relies on industry leading head gasket manufactures to ensure our head gasket sets will provide the best fit and sealing properties when used with Edelbrock aluminum cylinder heads. Edelbrock head gaskets are manufactured from high-density materials and feature a superior design that performs under pressure and provides a long-lasting seal, without re-torqueing.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.