1992 GMC C1500 Performance Engines

Essential 1992 GMC C1500 Performance Engines

Edelbrock – Performer Intake Manifold Small-Block Chevy (Part No.3706)

Performer Intake Manifold Small-Block Chevy

from

$381.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 Deg Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
  • Accepts Late-Model Choke; Waterneck; and HEI
  • Accepts A/C And Alternator
  • Accepts Exhaust Heated Chokes and Accepts EGR
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

Performer Series Retainer (Qty 16)

from

$95.99
Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:
  • Valve Spring Retainers for Use OE Cast Iron Heads
  • Superior Quality Heat-Treated Steel
  • Machined for Strength with Black Oxide Finish
  • Finish Ensures Rust and Corrosion Protection
See More

Edelbrock – Water Pump Big-Block Chevy Standard/Long in Satin Finish (Part No.8851)

Water Pump Big-Block Chevy Standard/Long in Satin Finish

from

$381.99
Product Features:
  • Standard Impeller Rotation
  • 0.625 in. Pilot Shaft
  • 0.750 in. Ball/Ball Bearing
  • 7.3125 in. Block To Hub Height
  • Satin Finish
See More

Edelbrock – Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet (Part No.3702)

Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet

from

$306.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched to Edelbrock Performer Intakes
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Engine Valve Cover Gasket Set

from

$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1803)

Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set

from

$26.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Spectre – Throttle Body Injection Spacer (Part No.11252)

Throttle Body Injection Spacer

from

$94.99
Manufactured from high quality machine finished aluminum, Spectre’s Throttle Body Spacers are engineered to improve engine performance. By providing added volume to the intake manifold and directing air through a tapered internal constriction, this spacer utilizes the Venturi effect to increase the speed of air flowing into your intake manifold. Spectre has designed a number of kits to fit a wide range of specific applications. Each kit includes the necessary gaskets and hardware to bolt directly to the factory components, making installation quick and easy.

Product Features:
  • Includes the necessary gaskets and hardware to bolt directly to the factory components
  • Each kit is designed for the applications listed
  • Manufactured from high quality machine finished aluminum
  • Can be installed in less than an hour using common hand tools with no drilling or cutting required
  • Simple to install
See More

Competition Cams – CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA (Part No.12-601-8)

CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA

from

$522.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)

PERFORMANCE REAR MAIN SEAL SET

from

$36.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Intake Bolt Kit (Part No.5003)

Intake Bolt Kit

from

$75.99
Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:
  • Chrome plated
  • Grade 8
  • 12-point head
  • AN washers with no exposed shoulder for a professional appearance
See More

Edelbrock – Pushrod Set for S/B Chevy (Part No.9646)

Pushrod Set for S/B Chevy

from

$203.99
Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:
  • 7.25 in. Length
  • 0.312 in. Diameter
  • 4130 Chromoly Steel Material
  • Black Oxide Finish
  • Made In The USA
See More

Edelbrock – Front Timing Cover Gasket Set #6998 For Big-Block Chevy, With Front Seal (Part No.6998)

Front Timing Cover Gasket Set #6998 For Big-Block Chevy, With Front Seal

from

$31.99
Edelbrock part #6998 Front Timing Cover Gasket set for Big-Block Chevy. Includes front cover gasket and front seal.

Product Features:
  • Includes replacement timing cover and water pump gaskets and the crank oil seal for big block Chevrolet engines
  • Features a tough, scuff-resistant silicone rubber coating
  • Helps in sealing without the engine warming up
  • Reduces fluid migration through the gasket
  • Resists fatigue
See More

Mr. Gasket – Ultra Seal: Screw-In Rocker Arm Studs (Part No.1076)

Ultra Seal: Screw-In Rocker Arm Studs

from

$65.99
Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Grade 8 Steel
See More

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Ultra Seal: Competition Screw-In Rocker Arm Studs

from

$94.99
Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Prevents Stud Flexing
  • Black Plated Finish
See More

Edelbrock – E-Tec-170 Small-Block Chevy Cylinder Head Flat Tappet Polished (Part No.609719)

E-Tec-170 Small-Block Chevy Cylinder Head Flat Tappet Polished

from

$889.99
The Edelbrock #609719 E-Tec Cylinder Heads are replacements for 302, 327, 350 & 400 c.i.d. S/B Chevy engines with “Vortec-style” manifolds. They feature an LT1-style raised runner intake port design for increased air-flow and ultimate performance. A uniqu
See More

Edelbrock – RPM Small-Block Chevy Cylinder Head SBC 70cc Hydraulic Flat Tappet Cam (Part No.60759)

RPM Small-Block Chevy Cylinder Head SBC 70cc Hydraulic Flat Tappet Cam

from

$1014.99
Product Features:
  • 50-State Street Legal Aluminum Cylinder Head
  • Out-of-the-Box Bolt-On Performance
  • 70cc Combustion Chambers Improve Performance
  • Retain Stock Compression Ratio
See More

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Advance And Retard Cam Bushings

from

$42.49
With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:
  • Advance the cam for increased torque and horsepower
  • Tune your powerband for more end torque or increase top end horsepower
  • Includes (4) offset bushings and (1) 0 degree bushing
  • Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
  • Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
  • Increase Top-End Horsepower
See More

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7810)

Performer-Link Adjustable True-Roller Timing Chain Set

from

$74.99


Product Features:
  • Solid Bushing Chain Resists Stretching
  • For Use with Stock or Edelbrock Camshafts
  • Stressproof Steel Crank Gears
  • 3 Keyway Setting Points To Ensure Accurate Timing
  • True Bearing Surface Rolls with the Sprockets
See More

B & M – Tork Master 3000 (Part No.20402)

Tork Master 3000

from

$499.99
Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
  • Washer Between Turbine and Cover
See More

B & M – Holeshot 2400 (Part No.70441)

Holeshot 2400

from

$709.99
Holeshot 2400 for GM 1998 to 2002 4L60E Camaro and Firebird with an LS1 engine Application: GM 1998 to 2002 4L60E Camaro and Firebird with LS1 A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benef

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

from

$65.99
Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

from

$151.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Non-Rotator Style: Dyno Tested and Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

Edelbrock – Intake Manifold Gasket for 1965-1990, Oval port 396-402-454 B/B Chevy (Part No.7203)

Intake Manifold Gasket for 1965-1990, Oval port 396-402-454 B/B Chevy

from

$32.99
Product Features:
  • Clean Positive Seal
  • Embossed Silicone Bead Surrounding The Port
  • Matched To Manifolds And Cylinder Heads
See More

Edelbrock – Intake Manifold Gasket for 1965-1990, Mark IV B/B Chevy, Rec Port (Part No.7208)

Intake Manifold Gasket for 1965-1990, Mark IV B/B Chevy, Rec Port

from

$30.99
Edelbrock part #7208 Intake Gaskets for 1965-1990, Mark IV 396-402-427-454-555, Rectangular Port 6 Bolt Flange with no crossover allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, an

Product Features:
  • 1.82″x2.46″
  • Rectangular Port Style
  • .060″ Thick
  • Two Piece Configuration
  • Composite Material
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1047)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$72.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1003)

Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts

from

$39.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

1992 GMC C1500 Performance Engines

Maybe you’re in the middle of a full rebuild of that 1992 GMC C1500. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 48 different Performance Engines in our inventory ranging from $17.49 to $1,028.99. That means you can find the exact parts or products you need to keep that 1992 GMC C1500 running smoothly.

Performance Engines are only as good as their brand. We stock 8 different brands to make sure you have plenty of trusted parts to choose from for your 1992 GMC C1500. Mr. Gasket, FEL-PRO Performance, and Weiand are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1992 GMC C1500, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 154 reviews in this category, some of the top rated parts include Action Plus Water Pumps with 3.7 stars and Action Plus Water Pumps with 1.5 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1992 GMC C1500 rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1992 GMC C1500 Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1992 GMC C1500 demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your C1500 the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular Spectre Performance Engines

We carry Spectre parts in our stock across Performance Throttle Body Spacers categories, plus more. For a 1992 GMC C1500, our most popular Spectre Performance Engines include:
Throttle Body Injection Spacer
from $94.99
(2)
Throttle Body Injection Spacer
Performance Throttle Body Spacers

Top 1992 GMC C1500 Performance Engines from Mr. Gasket

Mr. Gasket products are another trusted brand when it comes to Performance Engines for your 1992 GMC C1500. Popular Mr. Gasket parts include:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats

FAQs for 1992 GMC C1500 Performance Engines

What are the most purchased Performance Engines for the 1992 GMC C1500?

Out of 48 Performance Engines for the 1992 GMC C1500, the most popular in our inventory are:
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
from $39.49
(1)
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
Performance Engine Cylinder Head Gaskets
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $52.99
(1)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets
Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers
from $17.49
This product is not rated
Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers
Performance Intake Manifold Hardware

What are the top-rated 1992 GMC C1500 Performance Engines?

Top-rated Performance Engines for your 1992 GMC C1500 based on customer reviews/ratings are:
Action Plus Water Pumps
from $215.99
(3)
Action Plus Water Pumps
“I bought this item for my 1979 Camaro SBC for Street/Strip application. Water pump weighs 4 LBS less than factory, comes with its own cork gaskets. N”
Action Plus Water Pumps
from $215.99
(2)
Action Plus Water Pumps
“The twisted neck comes to far up on the hub. For a 2 groove pulley it causes the pulley to hit the water pump. You will also need new bolts for the”
Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish
from $329.99
(1)
Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish
“product fit as described , no complaints”