1994 Chevrolet C3500 Differentials

Product Features:

• GM10.5″ INTERNAL KIT (OPEN) 30 SPL

Product Features:

• CARRIER BEARING KIT FORD 10.5″

Yukon 1541H alloy right hand Full float rear axle for GM 14T with a length of 36-3/8″ inches and 30 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects.

Product Features:

• 30 spline
• 8 lug
• 36 3/8″ long
• Fits GM 10.5″ 14 bolt truck

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

DiffrlPinSupportBolt

Product Features:

• Oil baffle
• Fits Dana Spicer 80

aFe Power’s new rear differential cover brings performance engineering to the protection of your axle’s differential. This differential cover is constructed out of durable A356-T6 cast aluminum with reinforcing ribs for maximum strength. Mounting hardware is included for a hassle-free installation. An oil level sight glass and calibration plug set to the factory level prevents overfilling of the differential. A magnetic drain plug and a deep reach magnetic fill plug are provided for maximum protection. This cover is finished in black powder-coating with machined fins for a distinctive look. 4 Quart Gear Oil Capacity: This cover has about a 4 quart gear oil capacity at the factory fill level, factory cover holds about 3 quarts. Built-in External Fins: Built-in external fins transfer heat from the fluid to the outside air for maximum cooling. Magnetic Drain/Fill Plug: This system incorporates a magnetic drain and deep reach fill plug that captures loose particles for maximum rear-end protection. Oil Level Sight Glass: Large oil level sight glass with 1/8” NPT calibration plug set to the factory fluid level to eliminate overfilling. When it comes to engineering for power, performance, protection and value, aFe Power is the only choice.

Product Features:

• Constructed of Durable A356 Die Cast Aluminum
• Reinforcing Ribs and Black Powder coating w/Machined Fins
• Magnetic Drain and Fill Plugs Capture Loose Particles
• Large Oil Level Sight Glass w/ Calibration Plug

Differential

Yukon replacement standard open carrier case for Dana 80, 3.73 & down, (incl ABS) 35 & 37 spline.

Product Features:

• Standard open carrier case
• Fits Dana Spicer 80
• 3.73 and down ratio only
• Does not include spider gears

Product Features:

• Carrier shim kit
• Fits Dana Spicer 70 and 70HD

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1989-1997 GM 10.5″ 14 bolt truck
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

• Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
• 1/2″ x 18 thread

Product Features:

• CARRIER SHIM-DANA 60 & 70

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

• Cross pin shaft
• Fits Dana Spicer 60 and 70
• Powr Lok positraction only

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Yukon Trac Lok positraction internals for Dana 80 and with 35 spline axles. Uses round design cross pin. (Not for Dana 60 or 70). Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects. Dana 80 Trac Lok spider gears, 35spline (” round” design cross pin, NOT Dana 60 or NOT Dana 70 ).

Product Features:

• Spider gear kit
• Fit Dana Spicer 80 Powr Lok positraction with 35 spline axles
• Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

Product Features:

• Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
• Fits standard open differentials only

14T GM pinion shim kit.

Product Features:

• Pinion depth shims for GM 10.5″ 14 bolt truck

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
• Included are carrier bearings and races, pinion bearings and races, pinion seal, marking compound and brush.

Product Features:

• MINI INSTALL KIT DANA 80

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits 382A race
• All steel construction

Formulated to meet the specific requirements of Toyota, Lexus, and scion vehicles equipped with conventional (non-CVT) transmissions that require the use of ATF T-IV. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF T-IV is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

• Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
• Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
• Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
• Advanced anti-wear technology provides maximum protection to gears and bearings
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Product Features:

• Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80