from

$134.99

This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.

Product Features:

Complete with inner and outer tie rod ends
Restores OE alignment
Reduces tire wear
Improves steering response

from

$54.99

Worn suspension can cause loose steering, increased wear on tires, excess noise and lead to misalignments. Rein Automotive OE quality suspension parts are direct replacements for OE suspension parts and will reduce the wear on tires and reduce noise as well as tighten steering. Rein Automotive suspension parts come with the mounting hardware if required.

from

$72.53

The ultimate in safety and quality in steering and suspension is what sets LEMFORDER apart. The expertise that Lemfoerder has acquired through ball joint development work with leading automobile manufacturers is the guarantee that increasing demands for safety and comfort will be met. The products developed for the LEMFORDER brand are optimized right through to series maturity in thorough inspections and field trials, and then subjected to the toughest conditions in special wear tests. This approach gives you safety and reliability under all conditions – as service and costs only meet the customer’s demands when high quality is implemented systematically.

Product Features:

OE expertise and quality
Precision manufactured housing and components
Corrosion protection
Permanently attached boot
One-piece forged housing for easier steering

from

$47.69

P/S Pump Pulley

from

$49.13

The Lemfoerder Sway Bar Link is manufactured using only the highest quality materials and is designed to reduce road noise and vibration.

Product Features:

OE-Equivalent and direct fit application
Reduces squeaks, rattles, and vibration noise
Resistant to oil and other contaminants
Meets or exceeds OEM specifications

from

$21.99

Driveworks chassis parts help to provide powdered metal gusher bearing design enables grease to flow through the bearing to the stud for reduced friction and enhanced strength and stability. Also cover plate design allows for tighter tolerances vs. traditional cover plate designs, providing a more durable and extended life part. An enlarged ball joint receptacle in the lower control arm can cause a loose ball joint fit.

Product Features:

Gas Shielded Welding Reinforcement ensure the safety of driving under bad road condition
Wrench flats at the base of the stud allow for the use of sockets for easy installation

from

$31.99

CARDONE Steering Filters are uniquely designed to protect the steering system from damaging contaminates, which impacts performance and leads to premature power steering pump failure. These compact filters are easy to install, provide magnetic filtration, can be serviced in-line and are highly recommended to extend the life of your steering system. Available in 3/8″, 1/2″, and 5/8″ sizes to cover a most vehicle applications.

Product Features:

In-line filter with serviceable filter element
Patented built-in bypass that filters up to 190 micron particles
Designed to extend the life of the steering system
Sure-grip barb connections are included to ensure proper hose fitment

from

$48.49

CARDONE Steering Filters are uniquely designed to protect the steering system from damaging contaminates, which impacts performance and leads to premature power steering pump failure. These compact filters are easy to install, provide magnetic filtration, can be serviced in-line and are highly recommended to extend the life of your steering system. Available in 3/8″, 1/2″, and 5/8″ sizes to cover a most vehicle applications.

Product Features:

In-line filter with serviceable filter element
Patented built-in bypass that filters up to 190 micron particles
Designed to extend the life of the steering system
Sure-grip barb connections are included to ensure proper hose fitment

from

$46.99

CARDONE Steering Filters are uniquely designed to protect the steering system from damaging contaminates, which impacts performance and leads to premature power steering pump failure. These compact filters are easy to install, provide magnetic filtration, can be serviced in-line and are highly recommended to extend the life of your steering system. Available in 3/8″, 1/2″, and 5/8″ sizes to cover a most vehicle applications.

Product Features:

In-line filter with serviceable filter element
Patented built-in bypass that filters up to 190 micron particles
Designed to extend the life of the steering system
Sure-grip barb connections are included to ensure proper hose fitment

from

$228.99

CARDONE Remanufactured Power Steering Pumps are engineered to meet or exceed O.E. performance. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Every unit undergoes a hydraulic efficiency test to ensure reliable, long-lasting performance.

Product Features:

All critical components (cam packs, spool valves, etc.) are triple-tested to ensure product reliability.
All units are built with 100% new O-rings and premium-grade HNBR seals to prevent leaks. HNBR does not break down at high temperatures like conventional seal material.
Shafts are surfaced to precise specifications to eliminate premature seal wear and extend pump life.
Units are supplied with 100% tested and calibrated pressure relief valves.
Final pump assembly is computer-tested to measure pressure, bypass, fluid flow, valve operation, steering effort and noise to ensure reliable performance.
As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.

from

$183.99

Building on decades of experience using reverse engineering to remanufacture power steering products, CARDONE engineers have meticulously designed and tested our CARDONE New Power Steering Pumps to fit and perform like the original. Each unit is supplied with premium high-temperature seals for reliability you can count on.

Product Features:

Rigorous computer load testing ensures optimal performance and durability by incorporating real-world parameters during the test cycle.
Manufactured with premium grade, high-temperature seals for added durability under all driving conditions.
Precise bushing alignment prevents premature shaft and seal wear, significantly reducing noise and vibration.
Meets or exceeds O.E. performance.

from

$32.78

The ultimate in safety and quality in steering and suspension is what sets ZF-LEMFORDER apart. The expertise that Lemfoerder has acquired through ball joint development work with leading automobile manufacturers is the guarantee that increasing demands for safety and comfort will be met. The products developed for the LEMFORDER brand are optimized right through to series maturity in thorough inspections and field trials, and then subjected to the toughest conditions in special wear tests. This approach gives you safety and reliability under all conditions as service and costs only meet the customer’s demands when high quality is implemented systematically.

Product Features:

OE expertise and quality
Precision manufactured housing and components
Corrosion protection
Permanently attached boot
One-piece forged housing for easier steering

from

$247.99

This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.

Product Features:

Restores vehicle handling
With ball joint
Reduces vibration
With bushing

from

$283.99

This suspension control arm and ball joint assembly is a direct replacement for the original equipment on specific vehicle applications. An industry-leading evaluation process ensures a smooth ride, directional stability and predictable dynamics.

Product Features:

Trustworthy replacement – this control arm and ball joint assembly directly replaces the original assembly on specific vehicle applications
Complete repair – each assembly includes pre-installed ball joint and bushings, saving time and labor
Quality engineering – underwent industry-leading testing to ensure a smooth, stable and safe ride
Durably designed – additional coatings offer long-lasting rust and corrosion resistance

from

$97.99

MOOG premium control arms for foreign and domestic nameplates are engineered for structural strength and corrosion protection.

Product Features:

EASY TO INSTALL — Precision tolerances for easy installation and steering alignment giving you a perfect fit right out of the box
HIGHLY PRECISE ENGINEERING — Optimized bushings for quiet operation and resistance to wear, salt, road grime and oils
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
INSTALLATION READY — Pre-installed ball joints with sealed sockets for maintenance-free operation
LONG LIFE — Ball stud shape ensures fatigue life, compensating for sag and suspension and adding extra swing when you need it
ENHANCED STRUCTURAL STRENGTH — Heat treated to match or exceed OE requirements to inhibit premature failure
ADDED CORROSION PROTECTION — Coated studs and e-coated cast iron and steel control arms inhibit premature deterioration

from

$153.99

This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.

Product Features:

Restores vehicle handling
With ball joint
Reduces vibration
With bushing

from

$3.52

The FEQ idler arm bushing is designed to restore the idler arm to factory-like new condition. The FEQ OE quality replacement idler arm bushing is designed to reduce front-end vibration, shimmy and unsafe handling.

Product Features:

Improves steering response
Repairs worn components
Reduces vibration
Reduces tire wear

from

$3.55

Hose Clamp

from

$31.45

The Lemfoerder Idler Arm meets OE specifications and help to eliminate front-end vibration, shimmy and unsafe handling. The Lemfoerder idler arm is manufactured to exacting OE tolerances for a proper fit and function.

Product Features: