1993 Pontiac Firebird Suspension Parts

Essential 1993 Pontiac Firebird Suspension Parts

Firestone Ride-Rite – Portable, Maximum 130 Psi, 18 Amps, With Compressor Only (Part No.9284)

Portable, Maximum 130 Psi, 18 Amps, With Compressor Only

from

$251.99
The Air Command Standard Duty Dual Electric Air Compressor System Kit Allows You To Adjust Your Air Springs With The Touch Of A Button. It Offers A Built in Air Source For Your Suspension System, Making It Easy To Alter Your Springs To Align With The Load Type And Environment. When Shopping For Air Accessories, You will Find That Firestone Air Command Standard Duty Dual Electric Air Compressor System Kit Is Designed To Have A Couple Of Special Benefits. First, The Air Command Standard Duty Dual Electric Air Compressor System Kit Comes Ready To Install, So You Can Set It Up And Get Back To The Road where You Want To Be. Just Connect A Few Wires To The Compressor And A Few To Your Vehicle. The Air Lines And Wiring Harness Can Be Plugged Into The Same Side Of The Unit For Smoother Routing Of Lines And Power Supply. After The Air Command Standard Duty Dual Electric Air Compressor System Kit Is Properly Installed, You Can Make Pressure Adjustments By Pressing A Single Button. This Air Command Standard Duty Dual Electric Air Compressor System Kit Component Allows For Side To Side Or Front to rear Leveling, Real time Pressure Readout, And Dual Left And Right PSI And Pressure Control Readouts. The Air Command Standard Duty Dual Electric Air Compressor System Kit Easy to read Needle Gauge Can Be Viewed Day Or Night, Without Straining Or Squinting Your Eyes. Prior To Installing The Air Command Standard Duty Dual Electric Air Compressor System Kit, Review The Instructions And Identify All Of The Components To Help Make Sure You Get Maximum Performance From Both Your Air Springs And Air Command Standard Duty Dual Electric Air Compressor System Kit. The Installation Steps Are Different Depending On Whether You are Enhancing An Existing Air Helper Spring System With The Air Command Standard Duty Dual Electric Air Compressor System Kit Or Installing It With A New Air Spring System.

Product Features:
  • Individual Air Accessory Components Are Also Available, Including Compressors, Air Tanks, And Mounting Solutions, Providing A Wide Variety Of Air Control Assist Solutions
  • Adjust The Ride For Various Load And Road Conditions With A Switch, Remote Or Mobile App
  • Provides An Instant Air Source For The Air Helper Springs Or Accessories
  • Dual Point Fill (Both Air Springs Fill Independently Of Each Other)
  • Light Duty Compressor Specs (120 PSI Max Air Pressure, 9 Percent Duty Cycle, 0.32 CFM)
See More

Monroe – Strut-Mate Strut Mounting Kit (Part No.902947)

Strut-Mate Strut Mounting Kit

from

$104.99
Every new strut deserves a Monroe® Strut-Mate® Mounting Kit. Designed to reduce noise and vibration, Strut-Mate Mounting Kits complement the ride control characteristics of Monroe struts. Install when replacing conventional struts or springs.

Product Features:
  • PERFECT PAIRING — Ideal match for the ride control characteristics of Monroe® struts, replace all worn strut components with quality Monroe parts (sold separately) for a complete four-corner ride control upgrade
  • REDUCES NOISE AND VIBRATION — Features advanced elastomer technology for enhanced metal-to-rubber bonding that reduces noise, vibration and memory steer for improved performance
  • REPLACES OE — Available for most Monroe strut applications, this is a direct fit for replacing the OE strut mount
  • RIGOROUS TESTING — Fit checked and ride tested for quality you can count on
  • EASY TO INSTALL — Includes premium-quality replacement components where applicable – SAE-grade nuts and bolts, upper and lower spring isolators, OE-style bearings and mount, upper spring seat and front bearing plate that install easily
See More

Dorman – Help – Control Arm Bolt Kit (Part No.13505)

Control Arm Bolt Kit

from

$46.99
The Dorman Suspension Control Arm Bolt Kit includes all necessary components to secure the control arm to the vehicles chassis system. The bolts and hardware available in this repair kit are made from high-quality materials and designed to provide a longer service life.

Product Features:
  • Direct replacement for a proper fit every time
  • Durable steel construction for a longer service life
  • Secures suspension to vehicle frame
  • Manufactured to strict engineering quality standards
See More

Suncore – Complete Strut Assem (Part No.55S11993)

Complete Strut Assem

from

$154.99
Complete Strut Assem

Carquest Premium – Multi Purpose Relay (Part No.RAA1256)

Multi Purpose Relay

from

$24.99
Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

MOOG – Coil Spring Set (Part No.5610)

Coil Spring Set

from

$145.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:
  • 100% Load tested
  • Easy to install
  • Provides like-new steering
  • Designed to lower stresses for longer service life
  • Worn or sagging coil springs can cause premature tire wear due to vehicle misalignment
See More

Suncore – Quick Strut Kit (Part No.2-55S11993-001)

Quick Strut Kit

from

$304.99
Quick Strut Kit

Firestone Ride-Rite – Controls Two Air Springs Individually, Switch Operated (Part No.2219)

Controls Two Air Springs Individually, Switch Operated

from

$1023.99
Designed to provide inflation control of your air helper springs. This kit will be an asset to your vehicle, meeting nearly all of your air supply needs.

Product Features:
  • Individual Air Accessory Components Are Also Available, Including Compressors, Air Tanks, And Mounting Solutions, Providing A Wide Variety Of Air Control Assist Solutions
  • Provides An Instant Air Source For The Air Helper Springs Or Accessories
  • Dual Point Fill (Both Air Springs Fill Independently Of Each Other)
See More

MOOG – Control Arm Bushing Kit (Part No.K6109)

Control Arm Bushing Kit

from

$24.99
Backed by superior materials and rigorous testing, MOOG control arm bushings deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • HIGHLY PRECISE ENGINEERING — Optimized for quiet operation and resistance to wear, salt, road grime and oils
  • PREMIUM MATERIALS — Made from high-quality elastomer compounds for durability and ride performance
  • OE-STYLE DESIGN — Engineered to match or exceed OE requirements
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • Metal rib design helps lock the inner tube within frame pocket
  • Metal surfaces are phosphate coated for corrosion protection
See More

Monroe – Strut-Mate Strut Coil Spring Seat & Coil Spring Insulator (Part No.904962)

Strut-Mate Strut Coil Spring Seat & Coil Spring Insulator

from

$21.29
Every new strut deserves a Monroe® Strut-Mate® Mounting Kit. Designed to reduce noise and vibration, Strut-Mate Mounting Kits complement the ride control characteristics of Monroe struts. Install when replacing conventional struts or springs.

Product Features:
  • PERFECT PAIRING — Ideal match for the ride control characteristics of Monroe® struts, replace all worn strut components with quality Monroe parts (sold separately) for a complete four-corner ride control upgrade
  • REDUCES NOISE AND VIBRATION — Features advanced elastomer technology for enhanced metal-to-rubber bonding that reduces noise, vibration and memory steer for improved performance
  • REPLACES OE — Available for most Monroe strut applications, this is a direct fit for replacing the OE strut mount
  • RIGOROUS TESTING — Fit checked and ride tested for quality you can count on
  • EASY TO INSTALL — Includes premium-quality replacement components where applicable – SAE-grade nuts and bolts, upper and lower spring isolators, OE-style bearings and mount, upper spring seat and front bearing plate that install easily
See More

ACDelco – 10-Way Female White Multi-Purpose Pigtail (Part No.PT150)

10-Way Female White Multi-Purpose Pigtail

from

$111.99
ACDelco GM Original Equipment Pigtail Connectors are connectors ready to be spliced into vehicle harnesses, and are GM-recommended replacements for your vehicle’s original components. These original equipment pigtail connectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:
  • Protective outer coverings help provide long-lasting durability
  • Color-coded wires allow for easy installation
  • GM-recommended replacement part for your GM vehicle’s original factory component
  • Offering the quality, reliability, and durability of GM OE
  • Manufactured to GM OE specification for fit, form, and function
See More

Lakewood – Drag Shock-90/10:Ford/GM/Mopar (Part No.40101)

Drag Shock-90/10:Ford/GM/Mopar

from

$99.19
Drag Shock-90/10:Ford/GM/Mopar

Energy Suspension – Hyper-Flex System (Part No.3.18119R)

Hyper-Flex System

from

$336.99
Product Features:
  • Incredible Improvement in Control
  • Maintains Proper Caster and Camber Alignment
  • Increase in Handling and Control
  • Greatly Reduce Wheel Hop on Quick Acceleration
  • Even Braking Control is Improved
  • Better Suspension Stability
See More

MOOG – Coil Spring Set (Part No.60114)

Coil Spring Set

from

$242.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:
  • 100% Load tested
  • Easy to install
  • Provides like-new steering
  • Designed to lower stresses for longer service life
  • Worn or sagging coil springs can cause premature tire wear due to vehicle misalignment
See More

KYB – High Pressure Monotube Gas Shock (Part No.KG5524)

High Pressure Monotube Gas Shock

from

$52.99
The KYB Gas-a-just monotube shock absorber has additional performance advantages over the traditional twin-tube design: It can instantly, automatically adjust to your performance needs and never experiences fade due to aeration. The KYB Gas-a-just has two separate working chambers: An air-free hydraulic piston and valve area for responsiveness and control, and a second high-pressure nitrogen gas area with a floating piston that provides a comfortable ride during normal driving and adds instant performance on demand.

Product Features:
  • Adds Up To 25% More Damping Performance Over Original Equipment Shocks
  • Components And Valving Designed Specifically For The Camaro And Firebird
  • Gas-A-Just Monotubes Include Additional Damping Over One Design For Vehicles That Work, Tow, And Have Larger, Heavier Tires & Wheels
  • High Pressure Monotube Design Separates The Gas And Oil For Fade Free Operation And Instant Response
  • Fluid Leaking Can Be A Cause Of Shock Failure, The KYB Gas-A-Just Has An Ultra-Smooth Triple Chrome Plated Chrome Piston Rod To Reduce Seal Wear
  • The Higher Gas Pressure Of The KYB Gas-A-Just Responds Quickly To Improve Steering Response
  • Electronic Safety Systems Depend On The Suspension, Brakes And Tires Operating As The Vehicle Manufacturer Intended. The KYB Gas-A-Just Helps Keep Electronic Safety Systems Performing As Designed.
See More

KYB – Jounce Bumper and Bellows (Part No.SB103)

Jounce Bumper and Bellows

from

$31.49
KYB Strut Boot Kits keep your struts protected from dirt, dust, sand, salt and other road debris. These harmful elements cause abrasive wear to the polished shaft, upper seal and bushing. KYB Strut Boot Kits prevent these contaminants from entering the strut by covering the entire strut shaft in a highly durable plastic bellows. This can easily extend the life of the strut. The KYB Strut Boot Kit includes a poly foam travel-limiting bumper. Its designed to protect the strut from bottoming out and protects other components from extreme movement damage.

Product Features:
  • Superior Quality Boot Helps Protect The Strut Shaft From Leak-Causing Dirt And Debris
  • Poly Foam Bumper Prevents The Strut From Bottoming Out
  • Built With Design And Quality That Matches Or Exceeds One
  • Protects The Upper Seal And Bushing
See More

KAI – Shock Mount (Part No.GMK4020724671)

Shock Mount

from

$12.99
New Goodmark Shock Mount Brace, Welds To Trunk Floor, With Threaded Bolt Holes, 2 Required, Made Of Steel

Product Features:
  • Welds To Trunk Floor With Threaded Bolt Holes 2 Required Made Of Steel
  • Meets All Federal Motor Safety Standards
  • No Drilling Needed For Installation
  • No Modifications Needed For Installation
  • Direct Fit Replacement For Your Vehicle
  • Same Form Fit And Function As OE
  • Check Out The Large Selection Of Parts Available For Your Vehicle
See More

Valvoline – DEX/MERC ATF Conventional Automatic Transmission Fluid, 1 Quart (Part No.798153)

DEX/MERC ATF Conventional Automatic Transmission Fluid, 1 Quart

from

$11.99
Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON®, DEXRON®-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:
  • Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
  • Enhanced anti-shudder protection for smooth shifting and maximum power transfer
  • Developed with anti-wear technology to help improve transmission durability
  • Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
See More

Monroe – Shock-Mate Shock Absorber Boot Kit (Part No.SA1998)

Shock-Mate Shock Absorber Boot Kit

from

$13.29
Monroe® Shock-Mate® Shock Absorber Boot Kits are universal replacement shock boots use to protect the shock’s piston rod from dirt, mud and other contaminants – protecting the life of your shocks.

Product Features:
  • Protects the shock’s piston rod from damage
  • Universal design for easy installation
  • Tie-strap included for a secure fit
  • Constructed from high quality urethane for maximum durability
  • Multiple color choices available
See More

MOOG – Strut Bellows (Part No.K90462)

Strut Bellows

from

$35.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:
  • Easy to install
  • Restores like-new steering and handling
  • Construction and design validated by MOOG engineers
  • Engineered to meet or exceed OE requirements
  • Incorporates proven design and engineering features
See More

Monroe – Strut-Mate Strut Boot Kit (Part No.63621)

Strut-Mate Strut Boot Kit

from

$27.99
Designed to protect the strut, the Monroe® Strut-Mate® Boot Kit is the perfect replacement for a damaged jounce bumper or boot. Heavy-duty construction and unique design features make it the ideal choice for maximum rod protection and improved strut life.

Product Features:
  • REPLACES DAMAGED JOUNCE BUMPER OR BOOT — Avoid premature strut failure by replacing missing or damaged strut components
  • PROTECTS PISTON ROD — Protects piston rod finish from rust and corrosion and helps reduce oil leakage
  • KEEPS MOISTURE AND DIRT OUT — Self-draining design eliminates retention of moisture and other unwanted debris
  • ENHANCES STRUT LIFE — Delivers protection from severe suspension movement to improve strut durability
  • PERFECT PAIRING — Ideal match to protect strut rods, replace all worn strut components with quality Monroe struts (sold separately) for a complete four-corner ride control upgrade
  • EASY TO INSTALL — Direct fit OE replacement with firm friction connection that helps keep the boot in place
  • BUILT TO LAST — Soft-entry jounce bumper made of closed cell, micro-cellular urethane for maximum durability and to help reduce severe impacts
See More

Monroe – Max-Air Air Shock Absorber (Part No.MA708)

Max-Air Air Shock Absorber

from

$108.99
Ideal for hauling, Monroe® Max-Air® shock absorbers can be inflated or deflated up to 150 PSI to maintain level height with additional weight up to 1,200 lbs. (capacity is limited by vehicle suspension, tires and transmission. See vehicle owner’s manual.)

Product Features:
  • MAINTAIN RIDE HEIGHT UNDER LOAD — Air chamber can be inflated or deflated up to 150 PSI to maintain level height with additional weight up to 1,200 lbs. (capacity is limited by suspension, tires and transmission, see owner’s manual)
  • EASY TO ADJUST — Special air fitting resists air leakage and ties into factory system (where applicable) or manually inflates with an air compressor, pair with Monroe air shock accessory and shock air hose AK kits (varies by application)
  • EXCEPTIONAL HANDLING — Full-displaced valving on compression and extension cycles for a smooth ride
  • BUILT TO LAST — Hardened and precision ground piston rod for consistent performance, sintered iron piston for enhanced durability and longer service life and lubricated air sleeve reduces friction for smooth operation
  • CONSISTENT RIDE — OE all-weather fluid contains special modifiers to handle extreme temperatures and help reduce friction and ensure smooth rod reaction
  • Sintered Iron Piston: Stronger than traditional metals, enhances durability for longer service life.
  • Special Air Fitting: Resists air leakage.
See More

Monroe – Max-Air Air Shock Absorber (Part No.MA711)

Max-Air Air Shock Absorber

from

$158.99
Ideal for hauling, Monroe® Max-Air® shock absorbers can be inflated or deflated up to 150 PSI to maintain level height with additional weight up to 1,200 lbs. (capacity is limited by vehicle suspension, tires and transmission. See vehicle owner’s manual.)

Product Features:
  • MAINTAIN RIDE HEIGHT UNDER LOAD — Air chamber can be inflated or deflated up to 150 PSI to maintain level height with additional weight up to 1,200 lbs. (capacity is limited by suspension, tires and transmission, see owner’s manual)
  • EASY TO ADJUST — Special air fitting resists air leakage and ties into factory system (where applicable) or manually inflates with an air compressor, pair with Monroe air shock accessory and shock air hose AK kits (varies by application)
  • EXCEPTIONAL HANDLING — Full-displaced valving on compression and extension cycles for a smooth ride
  • BUILT TO LAST — Hardened and precision ground piston rod for consistent performance, sintered iron piston for enhanced durability and longer service life and lubricated air sleeve reduces friction for smooth operation
  • CONSISTENT RIDE — OE all-weather fluid contains special modifiers to handle extreme temperatures and help reduce friction and ensure smooth rod reaction
  • Sintered Iron Piston: Stronger than traditional metals, enhances durability for longer service life.
  • Special Air Fitting: Resists air leakage.
See More

MOOG – Strut Mount (Part No.K6516)

Strut Mount

from

$117.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:
  • Engineered to meet or exceed OE requirements
  • Superior rubber to steel bonding for durability
  • High polish chrome steel bearing races
  • Replacement helps restore vehicle handling
  • Includes new spring seat insulator and installation hardware to eliminate noise issues
  • Electroplate and corrosion-resistant coating to help prevent galvanic corrosion
See More

KYB – Strut Mount (Part No.L3030569109KYB)

Strut Mount

from

$10.13
Strut Mount

Monroe – Monroe Shock Absorber Air Hose Kit (Part No.AK18)

Monroe Shock Absorber Air Hose Kit

from

$36.49
Monroe® is one of the automotive industry’s best-known and most trusted original equipment and aftermarket brands, having delivered innovative undercar solutions to leading global OE manufacturers and generations of professional technicians and vehicle owners. This heritage of leading-edge products and exceptional customer support has made Monroe® shocks, struts and other ride control components a preferred choice of automotive professionals worldwide.
See More

Monroe – Monroe Shock Absorber Air Hose Kit (Part No.AK64)

Monroe Shock Absorber Air Hose Kit

from

$25.99
Monroe® is one of the automotive industry’s best-known and most trusted original equipment and aftermarket brands, having delivered innovative undercar solutions to leading global OE manufacturers and generations of professional technicians and vehicle owners. This heritage of leading-edge products and exceptional customer support has made Monroe® shocks, struts and other ride control components a preferred choice of automotive professionals worldwide.
See More

1993 Pontiac Firebird Suspension Parts

You count on your 1993 Pontiac Firebird to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Suspension Parts. With 52 Suspension Parts ranging in price from $6.29 to $1,217.99, you’re sure to find everything you need for your 1993 Pontiac Firebird.

Brands matter. If you want to shop a specific Suspension Parts brand, we stock 15 different brands like Valvoline, Monroe, and Driveworks. 1993 Pontiac Firebird Suspension Parts start as low as $6.29!

One of the best ways to find top quality OEM or aftermarket Suspension Parts is by asking professionals. Short of that, you can shop with confidence thanks to our 144 extensive product reviews on 1993 Pontiac Firebird Suspension Parts. Some of the top-rated Suspension Parts products we carry are Jounce Bumper and Bellows with 3.2 stars and Strut Bellows with 2.2 stars.

Did we mention you can order your Suspension Parts from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Suspension Parts inventory for your 1993 Pontiac Firebird below to get started!

Top-Rated Suspension Parts Brands For Your 1993 Pontiac Firebird

Trusted Suspension Parts OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1993 Pontiac Firebird running right for years to come. In our inventory you’ll find brands like Valvoline, Monroe, Driveworks, and even more.

Popular Driveworks Suspension Parts

You’ll find popular Driveworks brand products across Shocks and Struts. All are waiting to get your 1993 Pontiac Firebird back on the road. Some of the top-rated Driveworks products in these categories are:
Strut Bellow
from $6.99
(7)
Strut Bellow
Strut Bellows

FAQs for 1993 Pontiac Firebird Suspension Parts

What are the most purchased Suspension Parts for the 1993 Pontiac Firebird?

Out of 52 Suspension Parts for the 1993 Pontiac Firebird, the most popular in our inventory are:
DEX/MERC ATF Conventional Automatic Transmission Fluid, 1 Quart
from $11.99
This product is not rated
DEX/MERC ATF Conventional Automatic Transmission Fluid, 1 Quart
Suspension Self-Leveling Unit Fluids
OESpectrum Passenger Car Shock Absorber
from $91.99
(3)
OESpectrum Passenger Car Shock Absorber
Rear Shock and Struts
Max-Air Air Shock Absorber
from $101.99
(1)
Max-Air Air Shock Absorber
Air Suspension Shocks

What are the top-rated 1993 Pontiac Firebird Suspension Parts?

Top-rated Suspension Parts for your 1993 Pontiac Firebird based on customer reviews/ratings are:
Jounce Bumper and Bellows
from $31.49
(9)
Jounce Bumper and Bellows
“I would buy them if I did the job again”
Strut Bellows
from $35.99
(5)
Strut Bellows
“Replaced the stretched front bellows and cracked bushing stops on my 2005 Mini Cooper S. Didn’t plan to replace them, but when I got the front struts ”
Coil Spring Set
from $121.99
(3)
Coil Spring Set
“1999 Trans am. Great cost savings.”