1993 Chevrolet S10 Drivetrains

Essential 1993 Chevrolet S10 Drivetrains

Driveworks – Universal Joint (Part No.DW-369)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging, having higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals to optimize grease retention and reduce contamination
See More

Valvoline – MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart (Part No.VV324)

MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart

from

$12.79
Product Features:
  • High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks
  • Long-life friction modifiers and premium base oils help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
  • Enhanced cleaning additives help reduce varnish formation and keep the transmission running properly longer
  • Engineered with a unique blend of viscosity modifiers and base oils to provide better oil flow at low temperatures and greater film protection at higher temperatures
See More

Yukon Gear – Pinion Install Kit For ’83-’97 GM 7.2" S10 And S15 Differential (Part No.13061)

Pinion Install Kit For '83-'97 GM 7.2" S10 And S15 Differential

from

$194.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:
  • Fits 1983-1997 GM 7.2″ IFS
  • Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.
See More

Yukon Gear – Pinion Depth Shims For GM 8.25" IFS, 8.5", 12 Bolt Car, Ford 8.8" & Chrysler 8.25" (Part No.55009)

Pinion Depth Shims For GM 8.25" IFS, 8.5", 12 Bolt Car, Ford 8.8" & Chrysler 8.25"

from

$27.99
8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:
  • Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″
See More

National – Multi Purpose Bearing (Part No.HB-88107-A)

Multi Purpose Bearing

from

$44.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Controlled heat treating process for lasting performance and extended bearing life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Yukon Gear – 7.5 GM Cover Gasket (Part No.23018)

7.5 GM Cover Gasket

from

$11.99
7.5 GM cover gasket.

Product Features:
  • Cover gasket
  • Fits GM 7.5″ and 7.625″
See More

National – Shaft Repair Sleeve (Part No.99166)

Shaft Repair Sleeve

from

$34.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

Dorman – 4WD Actuator Control Cable (Part No.600-601)

4WD Actuator Control Cable

from

$39.49
This 4WD actuator cable directly replaces the original equipment part on specific vehicle applications. It is reverse engineered to reliably restore proper functionality.

Product Features:
  • Direct replacement – this 4WD actuator cable matches the fit and function of the original cable on certain vehicle years, makes and models
  • Effective fix – installation restores four-wheel drive function interrupted by a failed original cable
  • Related repair – recommended for replacement when installing a new axle actuator
  • Trustworthy quality – backed by team of designers and engineers in the United States
See More

Yukon Gear – Ring Gear Bolt (Part No.33049)

Ring Gear Bolt

from

$6.99
Ring gear bolt for GM 7.5″, 7.6″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ & 8.6″ IRS. 7/16″ x 20.

Product Features:
  • Ring gear bolt for GM 7.5″, 7.625″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ and 8.6″ IRS
  • 7/16″ x 20
See More

Dorman – Rear Differential Cover (Part No.697-706)

Rear Differential Cover

from

$51.99
This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:
  • Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
  • Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
  • Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
  • Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
See More

USA Standard Gear – Standard Spider Gear Set For GM 7.5", 26 Spline (Part No.39023)

Standard Spider Gear Set For GM 7.5", 26 Spline

from

$156.99
Product Features:
  • Spider gear kit
  • Fits GM 7.5″ 26 spline open differential
  • Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
See More

Yukon Gear – 7.2IFS GM 01 & Up Envoy Disconnect Housing Seal (Part No.30292)

7.2IFS GM 01 & Up Envoy Disconnect Housing Seal

from

$44.99
7.2IFS GM 01 & up Envoy disconnect housing seal.

Product Features:
  • Disconnect housing seal
  • Fits 2001 and up GM 7.2″ IFS in GMC Envoy
See More

Driveworks – Differential Seal (Part No.S-223255)

Differential Seal

from

$7.49
Product Features:
  • Brand may vary by location
See More

National – Multi Purpose Seal (Part No.223020)

Multi Purpose Seal

from

$5.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

Yukon Gear – Posi Spring Kit For GM 7.5", With Preload Plates (Part No.33206)

Posi Spring Kit For GM 7.5", With Preload Plates

from

$153.99
Product Features:
  • Positraction spring kit
  • Fits GM 7.5″ and 7.625″ Dura Grip
  • Includes preload plates
See More

Powertrax – Lock Right Locker (Part No.1930-LR)

Lock Right Locker

from

$445.99
The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
  • Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
  • Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
  • Powertrax® = Extreme Traction Systems!
  • See More

    Motive Gear – Differential Bearing Kit – Koyo (Part No.R7.5GRL)

    Differential Bearing Kit - Koyo

    from

    $98.99
    Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

    Product Features:
    • GM7.5 BRG & SEAL KIT ’99-UP
    See More

    Yukon Gear – Yoke For GM 7.5" And 7.625" (Mech 3R) In A Triple Lip Design (Part No.41088)

    Yoke For GM 7.5" And 7.625" (Mech 3R) In A Triple Lip Design

    from

    $154.99
    Yukon yoke for GM 7.5″ and 7.625″ (mech 3R) in a triple lip design. 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring. This yoke uses inside clips. All Yukon yokes come with a one year warranty against manufacturing defects.

    Product Features:
    • Fits GM 7.5″ and 7.625″
    • 27 spline
    • Mechanics 3R u-joint size
    • 2.556″ snap ring span
    • 1.125″ cap diameter
    • Inside snap ring design
    • Strap style
    See More

    Yukon Gear – Replacement Carrier Shim Kit For Dana Spicer 44, 30 Spline Axles (Part No.55010)

    Replacement Carrier Shim Kit For Dana Spicer 44, 30 Spline Axles

    from

    $15.99
    Product Features:
    • Carrier shim kit for Dana Spicer 30 with 30 spline axles
    See More

    Pro-King – Differential Internal Nest Kit (Part No.741A717A)

    Differential Internal Nest Kit

    from

    $155.99
    Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

    Product Features:
    • All products are designed to meet or exceed OE quality, form, fit and funtion.
    See More

    Dorman – Help – Differential Shaft Lock Bolt (Part No.81048)

    Differential Shaft Lock Bolt

    from

    $5.99
    This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

    Product Features:
    • Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
    • Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
    • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
    • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
    See More

    National – Bearings (Part No.M88010)

    Bearings

    from

    $10.49
    National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

    Product Features:
    • Premium bearing design matches OEM specifications
    • Precision manufactured using premium-grade steel for outstanding durability and performance
    • Crowned raceways and rollers to ensure even load distribution for maximum life
    • Industry leading coverage
    • Professional technicians know they can depend on National
    See More

    SKF – Driveshaft Support with Bearing (Part No.K1030285149SKF)

    Driveshaft Support with Bearing

    from

    $197.95
    Rugged SKF drive shaft support bearings are built to meet or exceed OE specifications. They are also built on the years of experience that SKF has earned designing and supplying bearings to the world’s largest OE manufacturers. Engineered and manufactured to specific application requirements that deliver precise drive shaft alignment and support. Center support bearings are pre-lubricated and sealed with metal reinforced seals to prevent contamination. Rubber support cushions are manufactured from durable rubber compounds that provide maximum support while isolating the driveline shaft from damaging vibration. Drive shaft support frames are constructed from high quality steel or aluminum that provides additional strength and long life in harsh environments.

    Product Features:
    • OE Quality, fit and performance
    • Precise driveshaft alignment and support
    • Pre-lubricated and sealed
    • Metal reinforced seals to prevent contamination
    • Manufactured from durable rubber compounds
    See More

    Yukon Gear – The Carrier Bearing Puller (Part No.56072)

    The Carrier Bearing Puller

    from

    $883.99
    The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

    Product Features:
    • Carrier bearing puller
    • Works with an impact gun to safely and easliy remove carrrier bearings
    See More

    National – Bearings (Part No.110-L)

    Bearings

    from

    $83.99
    National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

    Product Features:
    • Premium bearing design matches OEM specifications
    • Precision manufactured using premium-grade steel for outstanding durability and performance
    • Controlled heat treating process for lasting performance and extended bearing life
    • Industry leading coverage
    • Professional technicians know they can depend on National
    See More

    National – Bearings (Part No.J-2416)

    Bearings

    from

    $26.49
    National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

    Product Features:
    • Premium bearing design matches OEM specifications
    • Precision manufactured using premium-grade steel for outstanding durability and performance
    • Available in both caged design and full complement
    • Industry leading coverage
    • Professional technicians know they can depend on National
    See More

    National – Multi Purpose Seal (Part No.710687)

    Multi Purpose Seal

    from

    $26.49
    National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

    Product Features:
    • Low swell in hydrocarbon fluids
    • Design type: spring loaded; multi-lip
    • Provides good low temperature capability
    • Temperature range: -40°F to 225°F; -40°C to 107°C
    • Delivers quality and reliable performance for every type of repair
    See More

    SKF – Output Shaft Seal (Part No.J1157204657SKF)

    Output Shaft Seal

    from

    $60.95
    Output Shaft Seal

    Popular 1993 Chevrolet S10 Drivetrains Categories

    1993 Chevrolet S10 Drivetrains

    You count on your 1993 Chevrolet S10 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 330 Drivetrains ranging in price from $1.99 to $1,839.99, you’re sure to find everything you need for your 1993 Chevrolet S10.

    Brands matter. If you want to shop a specific Drivetrains brand, we stock 24 different brands like Moog, Valvoline, and Driveworks. 1993 Chevrolet S10 Drivetrains start as low as $1.99!

    One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 5,663 extensive product reviews on 1993 Chevrolet S10 Drivetrains. Some of the top-rated Drivetrains products we carry are Universal Joint with 4.6 stars and Greaseable Super Strength Universal Joint with 4.2 stars.

    Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1993 Chevrolet S10 below to get started!

    Top-Rated Drivetrains Brands For Your 1993 Chevrolet S10

    Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1993 Chevrolet S10 running right for years to come. In our inventory you’ll find brands like Moog, Valvoline, Driveworks, and even more.

    Popular Felpro Drivetrains

    You’ll find popular Felpro brand products across Transfer Cases and Differentials. All are waiting to get your 1993 Chevrolet S10 back on the road. Some of the top-rated Felpro products in these categories are:
    TRANSFER CASE GASKET SET
    from $19.99
    (9)
    TRANSFER CASE GASKET SET
    Transfer Case Adapter Gaskets
    DIFFERENTIAL GASKET
    from $7.99
    (45)
    DIFFERENTIAL GASKET
    Rear Differential Cover Gaskets

    FAQs for 1993 Chevrolet S10 Drivetrains

    What are the most purchased Drivetrains for the 1993 Chevrolet S10?

    Out of 330 Drivetrains for the 1993 Chevrolet S10, the most popular in our inventory are:
    Synchromesh Manual Transmission Fluid: Low-Temperature
    from $11.99
    (104)
    Synchromesh Manual Transmission Fluid: Low-Temperature
    Differential Oil
    Greaseable Premium Universal Joint
    from $26.99
    (89)
    Greaseable Premium Universal Joint
    U-Joints
    Greaseable Premium Universal Joint
    from $19.99
    (82)
    Greaseable Premium Universal Joint
    U-Joints

    What are the top-rated 1993 Chevrolet S10 Drivetrains?

    Top-rated Drivetrains for your 1993 Chevrolet S10 based on customer reviews/ratings are:
    Universal Joint
    from $15.99
    (52)
    Universal Joint
    “Great product.. Nice easy install”
    Greaseable Super Strength Universal Joint
    from $34.99
    (48)
    Greaseable Super Strength Universal Joint
    “Moog and advanced auto got me out of a bad situation with an amazing part ( u”
    Bearings
    from $16.99
    (39)
    Bearings
    “Perfect fit. Make sure you get your bearings completely filled with grease when reassembling your hubs.”