1993 Cadillac Fleetwood Performance and Racing Products

Essential Performance and Racing Products for 1993 Cadillac Fleetwoods

MSD Ignition – Direct-Fit Replacement Coil with Improved Energy Output and Easy Installation (Part No.5526)

Direct-Fit Replacement Coil with Improved Energy Output and Easy Installation

from

$65.99
These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.

Product Features:
  • Replacement Coil For GM Dual Connector Coil
  • Improved Turns Ratio
  • Lower Primary Resistance
  • Bolt-In replacement coil
  • Produce More Output Voltage
  • Smooth Idle
See More

B & M – Holeshot 2400 (Part No.70419)

Holeshot 2400

from

$609.99
HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
  • New Turbine Hub
  • New Springs/Rollers In Stator
See More

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Ultra Seal: Competition Screw-In Rocker Arm Studs

from

$94.99
Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Prevents Stud Flexing
  • Black Plated Finish
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1470)

Exhaust Manifold Gasket Set

from

$49.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Energy Suspension – Control Arm Bushing Set (Part No.3.3167R)

Control Arm Bushing Set

from

$55.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:
  • Maintains Better Alignment While Driving
  • Full Floating and Non Binding
  • Fits Into the Remaining Stock Control Arms
See More

Edelbrock – Performer Buick 3.8L, 4.1L V6 Intake Manifold (Part No.5486)

Performer Buick 3.8L, 4.1L V6 Intake Manifold

from

$381.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • Not for C-3 and C-4 Electronic Fuel Mngmt Systems
See More

FAG US – CUP (Part No.LM48510)

CUP

from

$7.69
CUP

Edelbrock – Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp) (Part No.70050)

Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp)

from

$735.99


Product Features:
  • Designed For Carbureted V8 Engines
  • Simple To Install
See More

Energy Suspension – Control Arm Bushing Set (Part No.3.3167G)

Control Arm Bushing Set

from

$57.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:
  • Maintains Better Alignment While Driving
  • Full Floating and Non Binding
  • Fits Into the Remaining Stock Control Arms
See More

PerTronix – D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor (Part No.D9007)

D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor

from

$30.99
Wiring Harness and CapacitorPremium quality wire harness and capacitor insure good connection and “static free” operation.

Product Features:
  • PerTronix D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor
  • Premium quality wire harness and capacitor.
See More

K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2002)

Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine

from

$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:
  • HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
  • VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
  • PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
  • EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
  • EASY TO REMOVE: Fast and easy Wrench-Off removal
  • HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
  • HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
See More

Spectre – Valve Cover (Part No.5280)

Valve Cover

from

$14.99
Spectre’s Valve Cover Hold Downs feature high quality steel construction with a triple chrome-plated finish. Manufactured for an optimum fit, this product’s hex heads include a decorative O-ring cap for a customizable appearance to suit your needs. Sold 4 per package, these studs are intended to fit standard height Chevy Center bolt valve covers.

Product Features:
  • 4 bolts included in each package
  • Allen head includes decorative O-ring cap
  • Triple chrome-plated finish
  • Fits standard height Chevy Center bolt valve covers
See More

Energy Suspension – Ball Joint Dust Boot Set (Part No.9.13128R)

Ball Joint Dust Boot Set

from

$10.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:
  • Easy to Install
  • Superior Material
  • Lasts Longer
  • Looks Great
See More

Mr. Gasket – A/Tdipstick (Part No.9704G)

A/Tdipstick

from

$79.99
Billet aluminum handle with flexible braded steel tube mounts to the firewall. 29-3/4 inch long.

Product Features:
  • Braided Stainless Steel
  • Firewall Mounting
  • Includes Oil Fill Tube
See More

Edelbrock – Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet (Part No.3702)

Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet

from

$306.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched to Edelbrock Performer Intakes
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2919)

Engine Crankshaft Seal Kit

from

$37.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
See More

Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)

Tie Rod Dust Boot

from

$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:
  • Easy to Install
  • Superior Material
  • Saves Your Tie Rods
  • Lasts Longer
  • Looks Great
See More

Energy Suspension – High Performance Sway Bar End Link Kit with Hardware (Part No.9.8117R)

High Performance Sway Bar End Link Kit with Hardware

from

$26.99
Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.

Product Features:
  • Made from HYPER-Flex Polyurethane
  • Allows Vehicle to Work At Maximum Efficiency
  • Easy to Install
  • Superior Performance and Greater Longevity
  • Lasts Much Longer Than OEM Rubber End Links
See More

Motive Gear – Performance Differential Ring and Pinion (Part No.G885342)

Performance Differential Ring and Pinion

from

$322.99


Product Features:
  • GM 10BL 8.5 R/P 3.42 FRT/REAR MGP
See More

B & M – Flexplate (Part No.20238)

Flexplate

from

$200.99
As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1986 to 1997 small block Chevy V8 engines (externally balanced) with one piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, 10.75 inch bolt pattern, 153 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:
  • NHRA/IHRA Legal For All Classes
  • Includes SFI Certification Sticker
  • Ideal For Street Applications
  • To Extreme Duty Racing
  • To High RPM Use
See More

B & M – Transkit For 87-93 TH700R4 Transmission (Part No.70233)

Transkit For 87-93 TH700R4 Transmission

from

$564.99
A B&M transmission in a box! Transform your automatic transmission into a full-tilt B&M performer! This is our ultimate transmission kit – it comes complete with full instructions on how to assemble your transmission to B&M specifications.

Product Features:
  • High Perf. Friction Materials
  • Complete Overhaul Gasket Set
  • Modification Components
  • Replacement Valves
  • Replacement Springs
  • Drain Plug Kit Included
See More

Accel – GM Ext. Coil 90-95 Ign Module (Part No.35370)

GM Ext. Coil 90-95 Ign Module

from

$158.99
This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most GM ignition systems with the externally mounted module. 1990 thru 1995.

Product Features:
  • Fits Most Stock And Modified Distributors
  • Dwell Control Circuit
  • Resists False Triggering
See More

Powertrax – Lock Right Locker (Part No.1910-LR)

Lock Right Locker

from

$376.99
The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
  • Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
  • Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
  • Powertrax® = Extreme Traction Systems!
  • See More

    Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

    Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

    from

    $65.99
    Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

    Product Features:
    • For Use With Cast Iron Heads
    • Springs Made of Highest Quality Spring Wire
    • Springs Precision Wound To Close Tolerances
    • Use with Original Equipment Heads Only
    See More

    Edelbrock – Performer Carb/Plate Nitrous Systems for Spread-Bore (Q-Jet)Carbs (50-75-100 Hp) (Part No.70002)

    Performer Carb/Plate Nitrous Systems for Spread-Bore (Q-Jet)Carbs (50-75-100 Hp)

    from

    $684.99


    Product Features:
    • Designed For Carbureted V6 And V8 Engines
    • Use With Single Or Dual Plane Manifolds
    • Power Increases From 50 to 100 HP
    • Plate Systems are Easy to Install
    • Precision EDM Machined Spray Bars Maximize Flow
    • Option of Silver Powder Coated or Polished Bottle
    • Recommend Ignition Retard ; Upgraded Fuel System
    • Requires Use of Premium Fuel
    See More

    Hurst – Automatic Shifter, Quarter Stick (Part No.3160006)

    Automatic Shifter, Quarter Stick

    from

    $426.99
    The Hurst Quarter Stick is designed for 2 and 3 speed applications. Its precision gate style mechanism ensures a positive feel. It features, a neutral safety switch, NHRA approved reverse lockout, and a brushed aluminum cover.

    Product Features:
    • Forward and Reverse Shift Patterns
    • Chrome Plated Trigger for Detent Activity
    • Factory Neutral Safety Switch
    • Compact And Lightweight
    • Roller Detent with Shifter Pattern
    See More

    Mr. Gasket – Ultra Seal; Timing Cover Bolts (Part No.6090)

    Ultra Seal; Timing Cover Bolts

    from

    $13.29
    The special self locking timing cover bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5. Application: Chevy small and big block, 1/4 inch-20 ix 1/2 inch,10 pieces.

    Product Features:
    • Ideal For Tight Spaces
    • Serrations Prevent Loosening
    • Flange Distributes Pressure
    • Zinc Plated Bolts
    • Grade 5 Material
    • Easy Installation
    See More

    FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

    Engine Timing Cover Gasket

    from

    $20.29
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Steel core gasket construction
    • Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
    • Not intended for use in emission controlled vehicles.
    See More

    Upgrade your 1993 Cadillac Fleetwood with Top-Quality Performance and Racing Products

    When it comes to maintaining or upgrading your 1993 Cadillac Fleetwood, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Cadillac or enhancing its overall performance, Performance and Racing Products are key to keeping your Fleetwood functioning at its best. At Advance Auto Parts, we offer a wide selection of 60 Performance and Racing Products for the 1993 Cadillac Fleetwood, designed to meet your needs without breaking the bank. From Performance Oil Filter replacements to Performance Engines upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

    Affordable Prices and Wide Selection

    Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1993 Cadillac Fleetwood at great prices. Our Performance and Racing Products inventory for this model ranges from just $7.69 to $926.99, with an average price of $214.47. Our 60 Performance and Racing Products in stock come from 15 trusted brands, so you’re sure to find the right part for your 1993 Cadillac Fleetwood without overspending.

    Top Brands and High Customer Satisfaction

    Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1993 Cadillac Fleetwood, we stock popular OEM and aftermarket Performance and Racing Products from top names like K&N, Energy Suspension, FEL-PRO Performance, and more. K&N Performance and Racing Products start at just $17.99 and boast an impressive 5 stars average rating from customers. Energy Suspension and FEL-PRO Performance also bring quality to the table, with Performance and Racing Products available starting at $9.99, and at an average 4 stars rating. With 199 customer reviews and counting, our 1993 Cadillac Fleetwood Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

    Explore Related Parts and More

    While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1993 Cadillac Fleetwood is always ready to roll. We’re committed to providing you with everything you need to keep your Fleetwood in top shape, all in one place. Start shopping confidently below for your 1993 Cadillac Fleetwood!

    Best-Selling Performance Oil Filters for 1993 Cadillac Fleetwoods

    Enhance the driving experience in your Cadillac with 1 quality Performance Oil Filter components, starting at $17.99.

    K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2002)

    Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine

    from

    $17.99
    K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

    Product Features:
    • HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
    • VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
    • PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
    • EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
    • EASY TO REMOVE: Fast and easy Wrench-Off removal
    • HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
    • HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
    See More

    Most Popular 1993 Cadillac Fleetwood Performance Engines

    Customize your Cadillac with 19 Performance Engines products like Performance Engine Cylinder Head Gaskets, Performance Intake Manifolds, and Performance Engine Valve Cover Gasket Sets, all priced under $789.99.

    FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1003)

    Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts

    from

    $39.49
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
    • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
    • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
    • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
    • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
    See More

    FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1004)

    Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

    from

    $52.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
    • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
    • Raises combustion sealing force to roughly three times that of standard head gaskets.
    • Steel wire rings for the greatest combustion seal strength.
    • Not intended for use in emission controlled vehicles.
    See More

    FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

    Engine Valve Cover Gasket Set

    from

    $23.49
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
    • Not intended for use in emission controlled vehicles.
    See More

    Edelbrock – Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish (Part No.2104)

    Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish

    from

    $329.99


    Product Features:
    • For Idle to 5500 RPM Street-Driven Performance
    • Dual-Plane Low-Rise Intake w/180 Deg Firing Order
    • Patented Runner Design Ensures Broad Torque Curve
    • Excellent Throttle Response and Mid-Range Power
    • 50-State Street Legal if Correct Carburetor Used
    • Accepts Late-Model Choke; Waterneck; and HEI
    • Accepts A/C And Alternator
    • Accepts Exhaust Heated Chokes
    See More

    Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

    Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

    from

    $151.99
    Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

    Product Features:
    • Complete Kit: Includes Retainers And Locks
    • Springs Made of Highest Quality Spring Wire
    • Springs Precision Wound To Close Tolerances
    • Includes Superior Quality Steel Retainers
    • Includes 7 deg. Heat-Treated Valve Stem Locks
    • Retainers and Locks Black Oxide Coated
    • Non-Rotator Style: Dyno Tested and Street Proven
    • Great Match to Edelbrock Camshaft Kit
    See More

    FEL-PRO Performance – PERFORMANCE VALVE COVER GASKET SET (Part No.1602)

    PERFORMANCE VALVE COVER GASKET SET

    from

    $23.49
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Die cut silicone rubber gaskets conform to out-of-flat covers
    • Great for on-again/off-again situations
    • Not intended for use in emission controlled vehicles.
    See More

    Edelbrock – Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet (Part No.3702)

    Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet

    from

    $306.99


    Product Features:
    • Designed for Optimum Torque and Acceleration
    • Maximum Performance From Idle through Mid-Range
    • Matched to Edelbrock Performer Intakes
    • Includes Hydraulic Lifters and Assembly Lube
    • Major Improvement in Throttle Response and Torque
    • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
    • Take The Guesswork Out Of Camshaft Selection
    See More

    Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

    Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

    from

    $111.99
    Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

    Product Features:
    • For Use With Cast Iron Heads
    • Springs Made of Highest Quality Spring Wire
    • Springs Precision Wound To Close Tolerances
    • Use with Original Equipment Heads Only
    See More

    FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1010)

    Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

    from

    $39.49
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
    • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
    • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
    • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
    • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
    See More

    Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

    Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

    from

    $65.99
    Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

    Product Features:
    • For Use With Cast Iron Heads
    • Springs Made of Highest Quality Spring Wire
    • Springs Precision Wound To Close Tolerances
    • Use with Original Equipment Heads Only
    See More

    FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1886)

    PERFORMANCE OIL PAN GASKET SET

    from

    $63.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
    • Not intended for use in emission controlled vehicles.
    See More

    FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

    Engine Timing Cover Gasket

    from

    $20.29
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Steel core gasket construction
    • Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
    • Not intended for use in emission controlled vehicles.
    See More

    Mr. Gasket – Ultra Seal: Head Gasket (Part No.5799G)

    Ultra Seal: Head Gasket

    from

    $68.99
    Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.130 inch, Compressed thickness 0.055 inch

    Product Features:
    • Five layer (graphite core/perforated steel outer layers) composite construction
    • Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
    • Provides excellent stability, compressibility and high temperature endurance
    • Coated with high temperature silicone to ensure sealing of engine fluids
    • Will not brinell (indent) aluminum cylinder heads
    • For high performance street, drag race and oval track use
    • Compatible w/High Octane Fuel
    • Compatible With Exotic Fuel
    See More

    FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2919)

    Engine Crankshaft Seal Kit

    from

    $37.49
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
    • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
    • Not intended for use in emission controlled vehicles.
    See More

    Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

    Ultra Seal: Competition Screw-In Rocker Arm Studs

    from

    $94.99
    Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

    Product Features:
    • Black Oxide Coated Grade 8 Steel
    • Kit Contains 16 Studs
    • Easy To Install
    • Heat Treated Steel
    • Prevents Stud Flexing
    • Black Plated Finish
    See More

    B & M – Torque Converter, Holeshot 3000 (Part No.70421)

    Torque Converter, Holeshot 3000

    from

    $789.99
    The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.

    Product Features:
    • Furnace Brazed Impeller
    • Steel Alloy Pump Drive Tube
    • Heavy Duty Needle Bearing
    • Between Stator and Turbine
    • Furnace Brazed Turbine
    See More

    B & M – Holeshot 2400 (Part No.70419)

    Holeshot 2400

    from

    $609.99
    HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

    Product Features:
    • Furnace Brazed Impeller
    • Steel Alloy Pump Drive Tube
    • Heavy Duty Needle Bearing
    • Between Stator and Turbine
    • Furnace Brazed Turbine
    • New Turbine Hub
    • New Springs/Rollers In Stator
    See More

    B & M – Torque Converter, Holeshot 2000 (Part No.70417)

    Torque Converter, Holeshot 2000

    from

    $544.99
    The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, new turbine hub and dual pattern drive lugs on some GM Holeshots.

    Product Features:
    • Furnace Brazed Impeller
    • Steel Alloy Pump Drive Tube
    • Heavy Duty Needle Bearing
    • Between Stator and Turbine
    • Furnace Brazed Turbine
    See More

    Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5894)

    Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

    from

    $147.99
    Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

    Product Features:
    • Complete Kit: Includes Retainers And Locks
    • Springs Made of Highest Quality Spring Wire
    • Springs Precision Wound To Close Tolerances
    • Includes Superior Quality Steel Retainers
    • Includes 7 deg. Heat-Treated Valve Stem Locks
    • Retainers and Locks Black Oxide Coated
    • Dyno Tested And Street Proven
    • Great Match to Edelbrock Camshaft Kit
    See More

    Top Picks for 1993 Cadillac Fleetwood Performance Exhaust Products

    Upgrade Cadillac Fleetwoods with top-quality Performance Exhaust Products parts, including 1 OEM and aftermarket selections for your 1993 model.

    FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1444)

    Exhaust Manifold Gasket Set

    from

    $31.49
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
    • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
    • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
    • Slotted bolt holes allow for easier header installation.
    • Not intended for use in emission controlled vehicles.
    See More

    In-Demand Performance Ignition Products for 1993 Cadillac Fleetwoods

    Select from 5 premium Performance Ignition Products parts for your 1993 Cadillac Fleetwood, with prices ranging from $65.99 to $158.99.

    MSD Ignition – High Energy Ignition Coil for GM HEI Distributors (Part No.8225)

    High Energy Ignition Coil for GM HEI Distributors

    from

    $112.99
    HEI owners now have a choice to replace their stock coil with the MSD high energy unitized coil for GM HEI distributors. This coil is a direct replacement of the stock coil and offers increased spark energy when used with the MSD HEI module, PN 83645. The coil features special low induc?tance, high temperature windings which charge faster to give you increased spark energy at higher rpm. The premium epoxy filled construction is designed to withstand harsh race applications as well as the wear and tear that daily usage dishes out, and still deliver more spark energy to the spark plugs.

    Product Features:
    • Direct performance replacement for GM HEI coil-in-cap dist.
    • 70:1 Turns Ratio
    • Lower Primary Resistance Produces High Voltage Output
    • Full Power Sparks To 9000 Rpm w/PN[83647] MSD HEI Module
    See More

    MSD Ignition – Coil; GM External HEI Coil; High Performance (Part No.8226)

    Coil; GM External HEI Coil; High Performance

    from

    $71.99
    Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.

    Product Features:
    • Direct performance replacement for GM dual connector coil
    • 100:1 Turns Ratio
    • Lower Primary Resistance Produces High Voltage Output
    • Works w/Stock Ignition As Well As MSD Ignitions
    See More

    Accel – GM Hei Supercoil Red/White (Part No.140005)

    GM Hei Supercoil Red/White

    from

    $113.99
    Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

    Product Features:
    • 10-15% More Energy
    • Direct Plug In Replacement Direct OE Fit
    • Advanced Bobbin Technology
    • Highly Specialized Silicone Magnetic Steel Cores
    • Similar to Standard Motor Products SMP Dr-32
    • Long Life And Great Looks
    See More

    MSD Ignition – Direct-Fit Replacement Coil with Improved Energy Output and Easy Installation (Part No.5526)

    Direct-Fit Replacement Coil with Improved Energy Output and Easy Installation

    from

    $65.99
    These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.

    Product Features:
    • Replacement Coil For GM Dual Connector Coil
    • Improved Turns Ratio
    • Lower Primary Resistance
    • Bolt-In replacement coil
    • Produce More Output Voltage
    • Smooth Idle
    See More

    Accel – GM Ext. Coil 90-95 Ign Module (Part No.35370)

    GM Ext. Coil 90-95 Ign Module

    from

    $158.99
    This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most GM ignition systems with the externally mounted module. 1990 thru 1995.

    Product Features:
    • Fits Most Stock And Modified Distributors
    • Dwell Control Circuit
    • Resists False Triggering
    See More

    Most Sold 1993 Cadillac Fleetwood Performance Distributors

    Explore our best-selling Cadillac parts for the 1993 Fleetwood among 2 OEM and aftermarket options starting from $26.99.

    PerTronix – D9001 Flame-Thrower HEI Distributor Advance Curve Kit (Part No.D9001)

    D9001 Flame-Thrower HEI Distributor Advance Curve Kit

    from

    $26.99
    Mechanical Advance Curve Ki tPrecision machined chromoly weights and center plate eliminate erratic timing. Three sets of springs, guide bushings and complete installation instructions make recurving your distributor easy.

    Product Features:
    • PerTronix D9001 Flame-Thrower HEI Distributor Advance Curve Kit
    • Precision machined chromoly weights and center plate.
    See More

    PerTronix – D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor (Part No.D9007)

    D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor

    from

    $30.99
    Wiring Harness and CapacitorPremium quality wire harness and capacitor insure good connection and “static free” operation.

    Product Features:
    • PerTronix D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor
    • Premium quality wire harness and capacitor.
    See More

    Top-Rated Performance and Racing Products Brands For Your 1993 Cadillac Fleetwood

    Shop for the best-rated brands offering Performance and Racing Products and other products for your 1993 Cadillac Fleetwoods. Below you’ll find some of our best rated Performance and Racing Products from K&N, Energy Suspension, and FEL-PRO Performance, and more. Performance and Racing Products from these brands that fit a 1993 Fleetwood start at just $9.99 and are rated as high as 5 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

    Popular K&N 1993 Cadillac Fleetwood Performance and Racing Products

    When it comes to maintaining or upgrading your 1993 Cadillac Fleetwood, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. K&N ticks all of those boxes. We offer a wide selection of K&N Performance and Racing Products, specifically designed for the 1993 Cadillac Fleetwood. With over 1 K&N brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $17.99. Plus, with over 35 customer reviews and an average rating of 5 stars, you can trust that our K&N Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

    Popular Energy Suspension 1993 Cadillac Fleetwood Performance and Racing Products

    Energy Suspension auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1993 Cadillac Fleetwood owner should feel confident when installing genuine Energy Suspension parts in their vehicle. To ensure the best fit and performance for your 1993 Fleetwood, Advance Auto Parts carries a full inventory of 6 Energy Suspension Performance and Racing Products. Plus you will be keeping your Cadillac in peak condition while saving money because prices on these Energy Suspension Performance and Racing Products range from $9.99 to $107.99, plus, with more than 10 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

    Control Arm Bushing Set
    from
    $55.99
    This product is not rated

    Control Arm Bushing Set

    “”

    Control Arm Bushing Set
    from
    $107.99
    This product is not rated

    Control Arm Bushing Set

    “”

    Ball Joint Dust Boot Set
    from
    $10.99
    This product is not rated

    Ball Joint Dust Boot Set

    “”

    FAQs for 1993 Cadillac Fleetwood Performance and Racing Products

    Which Performance and Racing Products are best-sellers for 1993 Cadillac Fleetwoods?

    Out of 60 Performance and Racing Products that fit 1993 Cadillac Fleetwoods, the following parts are the top sellers:

    What’s the price range for 1993 Cadillac Fleetwood Performance and Racing Products?

    Performance and Racing Product prices for the 1993 Cadillac Fleetwood start at $7.69 and go up to $926.99 for the most premium parts.

    What’s the average price of a Performance and Racing Product for a 1993 Cadillac Fleetwood?

    The average price for Performance and Racing Products for the 1993 Cadillac Fleetwood is $214.47. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

    Does Advance Auto Parts sell Performance and Racing Products for other Cadillac Fleetwood model years?

    Yes, we currently carry Performance and Racing Products for 31 model years of Cadillac Fleetwoods between 1965 and 1996. Performance and Racing Products are bought most frequently for the following model years: 1996, 1995, 1994, 1992, 1991, 1990, 1989, 1988, and 1987.

    What are the cheapest Performance and Racing Products for my 1993 Cadillac Fleetwood?

    The cheapest 1993 Cadillac Fleetwood Performance and Racing Products we carry in stock are:

    What are the top-rated Performance and Racing Products that fit the 1993 Cadillac Fleetwood?

    Out of 199 reviews by customers, our 1993 Cadillac Fleetwood Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1993 Cadillac Fleetwood and their top-rated products:

    What types of Performance and Racing Products do you sell for my 1993 Cadillac Fleetwood?

    As of 2/5/25, these are some of the most in-demand types of Performance and Racing Products for a 1993 Cadillac Fleetwood:

    Can I get help with 1993 Cadillac Fleetwood Performance and Racing Product orders?

    Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Cadillac Performance and Racing Products and more.

    What is your return policy for Cadillac Fleetwood Performance and Racing Products?

    Advance Auto Parts keeps returns simple. For new Cadillac Fleetwood Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.