1992 Pontiac Firebird Vehicle Hoods
More 1992 Pontiac Firebird Vehicle Hoods
Find your specific 1992 Pontiac Firebird original or aftermarket Vehicle Hoods below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 1992 Pontiac Firebird Vehicle Hoods
StrongArm – Liftgate Lift Support: 29.76" Ext Length, 6.7" Travel, 154 Lbs of Force, 1 Pk (Part No.B4897)
from
$35.99
Opening your vehicle’s rear hatch or checking under the hood should not be a serious safety hazard for you, your family or the technician working on your vehicle. Just like tire wear, your hood lift supports lose strength over time. Temperature changes, frequent usage, and driving environments all affect the lift power. StrongArm lift supports are designed for the everyday driver to be installed in minutes with no special tools required.
Product Features:
See More
Product Features:
- Heavy Gauge Steel Body
- Self-Cleaning Piston Assembly
- Rubber O-Ring Piston Seal
StrongArm – Liftgate Lift Support: 39.09" Ext Length, 9.68" Travel, 141 Lbs of Force, 1 Pk (Part No.A4900)
from
$38.99
Opening your vehicle’s rear hatch or checking under the hood should not be a serious safety hazard for you, your family or the technician working on your vehicle. Just like tire wear, your hood lift supports lose strength over time. Temperature changes, frequent usage, and driving environments all affect the lift power. StrongArm lift supports are designed for the everyday driver to be installed in minutes with no special tools required.
Product Features:
See More
Product Features:
- Heavy Gauge Steel Body
- Self-Cleaning Piston Assembly
- Rubber O-Ring Piston Seal
KAI – Deck Lid Latch (Part No.GMK402170570)
from
$104.99
New Goodmark Trunk Lid Latch
Product Features:
See More
Product Features:
- Made Of Steel
- Meets All Federal Motor Safety Standards
- No Drilling Needed For Installation
- No Modifications Needed For Installation
- Direct Fit Replacement For Your Vehicle
- Same Form Fit And Function As OE
- Check Out The Large Selection Of Parts Available For Your Vehicle
Atlas Lift – Lift Support (Part No.LS10309)
from
$32.99
Atlas Lift Supports are engineered to meet or exceed OE specifications to ensure your replacement will perform the same or better than your original lift supports. Atlas Lift supports are designed to prevent premature failures, with premium features such as a corrosion-resistant exterior, OE grade end connectors, and Dynamic Dampening Technology. Dynamic Dampening Technology (DDT) is a precision groove engineered into the tube of the lift support, which allows the hatch to open at the optimum speed to prevent “bouncing” or “Jumping” at the end of the stroke. Lift Supports’ performance and longevity are affected by consistent usage, temperature changes, contact with weather elements, pulling or hanging on the part, and can cause unsafe conditions if not changed when signs of failure are present. Atlas Lift Supports are easy to replace and can be changed in minutes No Special Tools Required. Atlas Lift Supports also provide easy to read install for a quick and easy installation. Make sure to Always Replace in Pairs!
Product Features:
See More
Product Features:
- Engineered to meet or exceed OE specifications- Always replace in Pairs, where applicable
- Easy Install – Less than 15 Minutes! based on average install time across all parts
- No Special Tools Required
- Certified Quality – IATF 16949 Certified- exceeds quality control standards and testing performance
- OE-Grade end connectors manufactured from high-strength materials to ensure proper fit and function
- OE-Performance Proprietary DYNAMIC DAMPENING TECHNOLOGY (DDT) provides a smooth open and close, where applicable
- World-class polished nitride-coated steel shafts provide corrosion resistance, smooth operation, and long life for the gas-seal
- Trilingual Install Instructions provided inside each package
StrongArm – Hood Lift Support: 20.88" Ext Length, 5.96" Travel, 62 Lbs of Force, 1 Pk (Part No.D4543)
from
$28.99
Opening your vehicle’s rear hatch or checking under the hood should not be a serious safety hazard for you, your family or the technician working on your vehicle. Just like tire wear, your hood lift supports lose strength over time. Temperature changes, frequent usage, and driving environments all affect the lift power. StrongArm lift supports are designed for the everyday driver to be installed in minutes with no special tools required.
Product Features:
See More
Product Features:
- Heavy Gauge Steel Body
- Self-Cleaning Piston Assembly
- Rubber O-Ring Piston Seal
StrongArm – Hood Lift Support: 12.87" Ext Length, 4.88" Travel, 146 Lbs of Force, 1 Pk (Part No.E4422)
from
$23.99
Opening your vehicle’s rear hatch or checking under the hood should not be a serious safety hazard for you, your family or the technician working on your vehicle. Just like tire wear, your hood lift supports lose strength over time. Temperature changes, frequent usage, and driving environments all affect the lift power. StrongArm lift supports are designed for the everyday driver to be installed in minutes with no special tools required.
Product Features:
See More
Product Features:
- Heavy Gauge Steel Body
- Self-Cleaning Piston Assembly
- Rubber O-Ring Piston Seal
StrongArm – Trunk Lift Support: 13.82" Ext Length, 4.72" Travel, 90 Lbs of Force, 1 Pk (Part No.E4529)
from
$36.99
Opening your vehicle’s rear hatch or checking under the hood should not be a serious safety hazard for you, your family or the technician working on your vehicle. Just like tire wear, your hood lift supports lose strength over time. Temperature changes, frequent usage, and driving environments all affect the lift power. StrongArm lift supports are designed for the everyday driver to be installed in minutes with no special tools required.
Product Features:
See More
Product Features:
- Heavy Gauge Steel Body
- Self-Cleaning Piston Assembly
- Rubber O-Ring Piston Seal
StrongArm – Liftgate Lift Support: 39.09" Ext Length, 9.68" Travel, 118 Lbs of Force, 1 Pk (Part No.A4967)
from
$42.99
Lift supports are pressurized cylinders that are used to support hoods, hatches and rear window glass in automotive applications. Lift supports are also used in many non-automotive applications. Each Strongarm lift support is custom engineered, and manufactured beyond industry standards to provide smoother operating, and longer lasting performance. Lift supports should be replaced in pairs to ensure safe, reliable support of your hood, hatch, or liftgate.
Product Features:
See More
Product Features:
- Exact fit original equipment design guarantees correct fit and function
- Engineered and built to meet or exceed original equipment quality standards
- Individually tested for performance and reliability
- Hardened, nitride plated steel shaft provides optimal durability
- Rubber O-ring piston seal prevents leakage for a controlled lift and consistent performance
- Heavy gauge steel body is electrostatically painted and heat cured to OE specs
- Self-Cleaning Piston Assembly provides smooth operation and more reliable performance
- Upper bushing is manufactured with quality precision providing exact fit and promotes longer operating life
- No special installation tools required
StrongArm – Hood Lift Support: 12.87" Ext Length, 4.88" Travel, 84 Lbs of Force, 1 Pk (Part No.E4134)
from
$24.99
Opening your vehicle’s rear hatch or checking under the hood should not be a serious safety hazard for you, your family or the technician working on your vehicle. Just like tire wear, your hood lift supports lose strength over time. Temperature changes, frequent usage, and driving environments all affect the lift power. StrongArm lift supports are designed for the everyday driver to be installed in minutes with no special tools required.
Product Features:
See More
Product Features:
- Heavy Gauge Steel Body
- Self-Cleaning Piston Assembly
- Rubber O-Ring Piston Seal
Atlas Lift – Lift Support (Part No.LS10322)
from
$32.99
Atlas Lift Supports are engineered to meet or exceed OE specifications to ensure your replacement will perform the same or better than your original lift supports. Atlas Lift supports are designed to prevent premature failures, with premium features such as a corrosion-resistant exterior, OE grade end connectors, and Dynamic Dampening Technology. Dynamic Dampening Technology (DDT) is a precision groove engineered into the tube of the lift support, which allows the hatch to open at the optimum speed to prevent “bouncing” or “Jumping” at the end of the stroke. Lift Supports’ performance and longevity are affected by consistent usage, temperature changes, contact with weather elements, pulling or hanging on the part, and can cause unsafe conditions if not changed when signs of failure are present. Atlas Lift Supports are easy to replace and can be changed in minutes No Special Tools Required. Atlas Lift Supports also provide easy to read install for a quick and easy installation. Make sure to Always Replace in Pairs!
Product Features:
See More
Product Features:
- Engineered to meet or exceed OE specifications- Always replace in Pairs, where applicable
- Easy Install – Less than 15 Minutes! based on average install time across all parts
- No Special Tools Required
- Certified Quality – IATF 16949 Certified- exceeds quality control standards and testing performance
- OE-Grade end connectors manufactured from high-strength materials to ensure proper fit and function
- OE-Performance Proprietary DYNAMIC DAMPENING TECHNOLOGY (DDT) provides a smooth open and close, where applicable
- World-class polished nitride-coated steel shafts provide corrosion resistance, smooth operation, and long life for the gas-seal
- Trilingual Install Instructions provided inside each package
Atlas Lift – Lift Support (Part No.LS10242)
from
$29.99
Atlas Lift Supports are engineered to meet or exceed OE specifications to ensure your replacement will perform the same or better than your original lift supports. Atlas Lift supports are designed to prevent premature failures, with premium features such as a corrosion-resistant exterior, OE grade end connectors, and Dynamic Dampening Technology. Dynamic Dampening Technology (DDT) is a precision groove engineered into the tube of the lift support, which allows the hatch to open at the optimum speed to prevent “bouncing” or “Jumping” at the end of the stroke. Lift Supports’ performance and longevity are affected by consistent usage, temperature changes, contact with weather elements, pulling or hanging on the part, and can cause unsafe conditions if not changed when signs of failure are present. Atlas Lift Supports are easy to replace and can be changed in minutes No Special Tools Required. Atlas Lift Supports also provide easy to read install for a quick and easy installation. Make sure to Always Replace in Pairs!
Product Features:
See More
Product Features:
- Engineered to meet or exceed OE specifications- Always replace in Pairs, where applicable
- Easy Install – Less than 15 Minutes! based on average install time across all parts
- No Special Tools Required
- Certified Quality – IATF 16949 Certified- exceeds quality control standards and testing performance
- OE-Grade end connectors manufactured from high-strength materials to ensure proper fit and function
- OE-Performance Proprietary DYNAMIC DAMPENING TECHNOLOGY (DDT) provides a smooth open and close, where applicable
- World-class polished nitride-coated steel shafts provide corrosion resistance, smooth operation, and long life for the gas-seal
- Trilingual Install Instructions provided inside each package
Atlas Lift – Lift Support (Part No.LS10308)
from
$28.99
Atlas Lift Supports are engineered to meet or exceed OE specifications to ensure your replacement will perform the same or better than your original lift supports. Atlas Lift supports are designed to prevent premature failures, with premium features such as a corrosion-resistant exterior, OE grade end connectors, and Dynamic Dampening Technology. Dynamic Dampening Technology (DDT) is a precision groove engineered into the tube of the lift support, which allows the hatch to open at the optimum speed to prevent “bouncing” or “Jumping” at the end of the stroke. Lift Supports’ performance and longevity are affected by consistent usage, temperature changes, contact with weather elements, pulling or hanging on the part, and can cause unsafe conditions if not changed when signs of failure are present. Atlas Lift Supports are easy to replace and can be changed in minutes No Special Tools Required. Atlas Lift Supports also provide easy to read install for a quick and easy installation. Make sure to Always Replace in Pairs!
Product Features:
See More
Product Features:
- Engineered to meet or exceed OE specifications- Always replace in Pairs, where applicable
- Easy Install – Less than 15 Minutes! based on average install time across all parts
- No Special Tools Required
- Certified Quality – IATF 16949 Certified- exceeds quality control standards and testing performance
- OE-Grade end connectors manufactured from high-strength materials to ensure proper fit and function
- OE-Performance Proprietary DYNAMIC DAMPENING TECHNOLOGY (DDT) provides a smooth open and close, where applicable
- World-class polished nitride-coated steel shafts provide corrosion resistance, smooth operation, and long life for the gas-seal
- Trilingual Install Instructions provided inside each package
StrongArm – Trunk Lift Support: 13.87" Ext Length, 4.32" Travel, 67 Lbs of Force, 1 Pk (Part No.E4632)
from
$23.99
Opening your vehicle’s rear hatch or checking under the hood should not be a serious safety hazard for you, your family or the technician working on your vehicle. Just like tire wear, your hood lift supports lose strength over time. Temperature changes, frequent usage, and driving environments all affect the lift power. StrongArm lift supports are designed for the everyday driver to be installed in minutes with no special tools required.
Product Features:
See More
Product Features:
- Heavy Gauge Steel Body
- Self-Cleaning Piston Assembly
- Rubber O-Ring Piston Seal
- Non-Stick Back-Up Ring
- Hardened Nitride Plated Steel Shaft
- Engineered In USA To OE Quality Standards For Performance And Durability
- IATF 16949, ISO 9001 Certified; Passes Extensive Quality Checks And Testing
- Easy To Install In Just Minutes. No Special Tools Required.
- Exact Fit Original Equipment Design Guarantees Correct Fit And Function
- Consistent Performance In All Weather Conditions
- Engineered And Built To Meet Or Exceed Original Equipment Quality Standards For Long Lasting Performance
- Replacing Your Worn Lift Supports Eliminates A Potentially Unsafe Condition In Your Vehicle
Atlas Lift – Lift Support (Part No.LS10316)
from
$29.99
Atlas Lift Supports are engineered to meet or exceed OE specifications to ensure your replacement will perform the same or better than your original lift supports. Atlas Lift supports are designed to prevent premature failures, with premium features such as a corrosion-resistant exterior, OE grade end connectors, and Dynamic Dampening Technology. Dynamic Dampening Technology (DDT) is a precision groove engineered into the tube of the lift support, which allows the hatch to open at the optimum speed to prevent “bouncing” or “Jumping” at the end of the stroke. Lift Supports’ performance and longevity are affected by consistent usage, temperature changes, contact with weather elements, pulling or hanging on the part, and can cause unsafe conditions if not changed when signs of failure are present. Atlas Lift Supports are easy to replace and can be changed in minutes No Special Tools Required. Atlas Lift Supports also provide easy to read install for a quick and easy installation. Make sure to Always Replace in Pairs!
Product Features:
See More
Product Features:
- Engineered to meet or exceed OE specifications- Always replace in Pairs, where applicable
- Easy Install – Less than 15 Minutes! based on average install time across all parts
- No Special Tools Required
- Certified Quality – IATF 16949 Certified- exceeds quality control standards and testing performance
- OE-Grade end connectors manufactured from high-strength materials to ensure proper fit and function
- OE-Performance Proprietary DYNAMIC DAMPENING TECHNOLOGY (DDT) provides a smooth open and close, where applicable
- World-class polished nitride-coated steel shafts provide corrosion resistance, smooth operation, and long life for the gas-seal
- Trilingual Install Instructions provided inside each package
Metro Mould – Cowl Seal (Part No.CS 15)
from
$110.99
Founded in 1918, Metro Moulded Parts, Inc. is the leading USA manufacturer of top quality molded detail rubber parts and sponge rubber weatherstripping for antique, classic, restoration cars and trucks, as well as late model vehicles. Metro’s detailed rubber parts are manufactured to meet or exceed the specifications of the original part. They are the finest reproductions available anywhere. Hood to Cowl Seal. 68 In. long. Each.
Product Features:
See More
Product Features:
- Jet black to match the color of the original part
- There’s no need to slam when you use Metro SUPERsoft weatherstripping products
- Exact fit
- High quality original equipment replacement part
- Made in the USA
Metro Mould – Cowl Seal (Part No.CS 15-C)
from
$25.49
Founded in 1918, Metro Moulded Parts, Inc. is the leading USA manufacturer of top quality molded detail rubber parts and sponge rubber weatherstripping for antique, classic, restoration cars and trucks, as well as late model vehicles. Metro’s detailed rubber parts are manufactured to meet or exceed the specifications of the original part. They are the finest reproductions available anywhere. Hood to Cowl Seal (excludes models with fiberglass hood). Replaces OEM part #14030759. Each.
Product Features:
See More
Product Features:
- Jet black to match the color of the original part
- There’s no need to slam when you use Metro SUPERsoft weatherstripping products
- Exact fit
- High quality original equipment replacement part
- Made in the USA
Metro Mould – Cowl Seal (Part No.CS 15-A)
from
$39.49
Founded in 1918, Metro Moulded Parts, Inc. is the leading USA manufacturer of top quality molded detail rubber parts and sponge rubber weatherstripping for antique, classic, restoration cars and trucks, as well as late model vehicles. Metro’s detailed rubber parts are manufactured to meet or exceed the specifications of the original part. They are the finest reproductions available anywhere. Hood to Cowl Seal. 51-1/2 In. long. Replaces OEM #14019217. Each.
Product Features:
See More
Product Features:
- Jet black to match the color of the original part
- There’s no need to slam when you use Metro SUPERsoft weatherstripping products
- Exact fit
- High quality original equipment replacement part
- Made in the USA
KAI – Cowl Seal (Part No.GMK4020374681S)
from
$49.99
New Goodmark Firewall Seal Kit, Includes Hood To Cowl, Cowl Panel, Wiper Motor To Firewall, And Steering Column Seals
Product Features:
See More
Product Features:
- Includes Hood To Cowl Cowl Panel Wiper Motor To Firewall And Steering Column Seals
- Meets All Federal Motor Safety Standards
- No Drilling Needed For Installation
- No Modifications Needed For Installation
- Direct Fit Replacement For Your Vehicle
- Same Form Fit And Function As OE
- Check Out The Large Selection Of Parts Available For Your Vehicle
KAI – Cowl Seal (Part No.GMK4021280701)
from
$35.99
New Goodmark Cowl Seal Center Section
Product Features:
See More
Product Features:
- Meets All Federal Motor Safety Standards
- No Drilling Needed For Installation
- No Modifications Needed For Installation
- Direct Fit Replacement For Your Vehicle
- Same Form Fit And Function As OE
- Check Out The Large Selection Of Parts Available For Your Vehicle
Metro Mould – Cowl Seal (Part No.CS 15-B)
from
$32.99
Founded in 1918, Metro Moulded Parts, Inc. is the leading USA manufacturer of top quality molded detail rubber parts and sponge rubber weatherstripping for antique, classic, restoration cars and trucks, as well as late model vehicles. Metro’s detailed rubber parts are manufactured to meet or exceed the specifications of the original part. They are the finest reproductions available anywhere. Hood to Core Support Seal. For models with air conditioning only. Each.
Product Features:
See More
Product Features:
- Jet black to match the color of the original part
- There’s no need to slam when you use Metro SUPERsoft weatherstripping products
- Exact fit
- High quality original equipment replacement part
- Made in the USA
Metro Mould – Cowl Seal (Part No.CS 40)
from
$21.99
Founded in 1918, Metro Moulded Parts, Inc. is the leading USA manufacturer of top quality molded detail rubber parts and sponge rubber weatherstripping for antique, classic, restoration cars and trucks, as well as late model vehicles. Metro’s detailed rubber parts are manufactured to meet or exceed the specifications of the original part. They are the finest reproductions available anywhere. Cowl Seal. 43-1/4 In. long. Each.
Product Features:
See More
Product Features:
- Jet black to match the color of the original part
- Dense rubber to match the original
- Exact fit
- High quality original equipment replacement part
- Made in the USA
Metro Mould – Cowl Seal (Part No.CS 15-D)
from
$12.79
Founded in 1918, Metro Moulded Parts, Inc. is the leading USA manufacturer of top quality molded detail rubber parts and sponge rubber weatherstripping for antique, classic, restoration cars and trucks, as well as late model vehicles. Metro’s detailed rubber parts are manufactured to meet or exceed the specifications of the original part. They are the finest reproductions available anywhere. Rear Hood to Corner Cowl Seals (excludes models with fiberglass hood). Pair.
Product Features:
See More
Product Features:
- Jet black to match the color of the original part
- There’s no need to slam when you use Metro SUPERsoft weatherstripping products
- Exact fit
- High quality original equipment replacement part
- Made in the USA
Popular 1992 Pontiac Firebird Vehicle Hoods Categories
1992 Pontiac Firebird Vehicle Hoods
Maybe you’re in the middle of a full rebuild of that 1992 Pontiac Firebird. Maybe you just need a couple of Vehicle Hoods. Either way, Advance Auto Parts has 10 different Vehicle Hoods in our inventory ranging from $23.99 to $42.99. That means you can find the exact parts or products you need to keep that 1992 Pontiac Firebird running smoothly.
Vehicle Hoods are only as good as their brand. We stock 3 different brands to make sure you have plenty of trusted parts to choose from for your 1992 Pontiac Firebird. StrongArm, Atlas Lift, and Metro Mould are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Vehicle Hoods for your 1992 Pontiac Firebird, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.
So if you’re in the market for aftermarket Vehicle Hoods to keep your 1992 Pontiac Firebird rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Vehicle Hoods Brands To Make Your 1992 Pontiac Firebird Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 1992 Pontiac Firebird demands trusted brand parts and products to keep it running. Many trusted brands of Vehicle Hoods make up Advance Auto Parts’ inventory, and all are ready to help make your Firebird the best it can be. Be sure to browse some of our top Vehicle Hoods brands and parts.
Popular StrongArm Vehicle Hoods
We carry StrongArm parts in our stock across Lift Supports categories, plus more. For a 1992 Pontiac Firebird, our most popular StrongArm Vehicle Hoods include:
from
$38.99
(8)
Liftgate Lift Support: 39.09" Ext Length, 9.68" Travel, 141 Lbs of Force, 1 Pk
Lift Supports
from
$23.99
(18)
Hood Lift Support: 12.87" Ext Length, 4.88" Travel, 146 Lbs of Force, 1 Pk
Lift Supports
from
$24.99
(1)
Hood Lift Support: 12.87" Ext Length, 4.88" Travel, 84 Lbs of Force, 1 Pk
Lift Supports
FAQs for 1992 Pontiac Firebird Vehicle Hoods
What are the most purchased Vehicle Hoods for the 1992 Pontiac Firebird?
Out of 10 Vehicle Hoods for the 1992 Pontiac Firebird, the most popular in our inventory are:
from
$23.99
This product is not rated
Trunk Lift Support: 13.87" Ext Length, 4.32" Travel, 67 Lbs of Force, 1 Pk
Lift Supports
