Name: Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet
Brand: Edelbrock
SKU: 3702
Price: 306.99 USD
Rating: 4.0 (1 reviews)

from

$306.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$29.99

Product Features:

Timing Chain Only

from

$42.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$147.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

Complete Kit: Includes Retainers And Locks
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Includes Superior Quality Steel Retainers
Includes 7 deg. Heat-Treated Valve Stem Locks
Retainers and Locks Black Oxide Coated
Dyno Tested And Street Proven
Great Match to Edelbrock Camshaft Kit

from

$68.99

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.130 inch, Compressed thickness 0.055 inch

Product Features:

Five layer (graphite core/perforated steel outer layers) composite construction
Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
Provides excellent stability, compressibility and high temperature endurance
Coated with high temperature silicone to ensure sealing of engine fluids
Will not brinell (indent) aluminum cylinder heads
For high performance street, drag race and oval track use
Compatible w/High Octane Fuel
Compatible With Exotic Fuel

from

$30.19

If you are changing your camshaft or replacing the timing set, make sure to replace this seal at the same time! Made from Nitrile rubber.

Product Features:

Nitrile Rubber And High Density Cork
Will Not Shrink Or Stick

from

$958.99

The Edelbrock #607519 Performer cylinder head is designed for 302, 327, 350 and 400 cid small-block Chevy engines up to 1986. This cylinder head includes your choice of 64cc (In order to retain stock compression ratio on 1970 and earlier small-blocks) or

Product Features:

Complete Single For Hydraulic Flat Tappet
70cc Combustion Chamber Volume
185cc Intake/65cc Exhaust Runner Volume
2.02 in. Intake/1.6 in. Exhaust Valve Diameter
0.562 in. Deck Thickness

from

$23.99

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

Repairs That Leaky Rear Main Sail
Silicone Rubber to Withstand Extreme Engine Oil Temperatures
Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
Injection Molded for Precise Fit

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$26.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$187.99

Product Features:

Case-Hardened Tubing
Surface Hardening
Welded Ends
0.3125 in. Diameter
Use with or without Hardened Steel Guideplates

from

$189.99

Product Features:

Case-Hardened Tubing
Welded Ends
5/16 in. Diameter
Use with or without Hardened Steel Guideplates

from

$75.99

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

Chrome plated
Grade 8
12-point head
AN washers with no exposed shoulder for a professional appearance

from

$17.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$95.99

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

Valve Spring Retainers for Use OE Cast Iron Heads
Superior Quality Heat-Treated Steel
Machined for Strength with Black Oxide Finish
Finish Ensures Rust and Corrosion Protection

from

$94.99

Manufactured from high quality machine finished aluminum, Spectre’s Throttle Body Spacers are engineered to improve engine performance. By providing added volume to the intake manifold and directing air through a tapered internal constriction, this spacer utilizes the Venturi effect to increase the speed of air flowing into your intake manifold. Spectre has designed a number of kits to fit a wide range of specific applications. Each kit includes the necessary gaskets and hardware to bolt directly to the factory components, making installation quick and easy.

Product Features:

Includes the necessary gaskets and hardware to bolt directly to the factory components
Each kit is designed for the applications listed
Manufactured from high quality machine finished aluminum
Can be installed in less than an hour using common hand tools with no drilling or cutting required
Simple to install

from

$394.99

Product Features:

High Rise/Dual Plane Design For Maximum Torque
Fully CNC Machined For A Perfect Fit
Square Bore Carburetor Flange
Exhaust Crossover For Improved Street Drivability
Permanent Mold Casting Process
Lighter/Smoother/Better Looking
More Consistent Castings

from

$438.99

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM street-driven power. Dual-plane high-rise intake with 180 degree firing order. Produces incredible top-end horsepower. Retains good throttle response and acceleration. Larger plenum and runners maximize other upgrades. Edelbrock total power package maximizes gains. Available in cast, polished or endurashine finish.

Product Features:

Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed for 1500 to 6500 RPM Street-Driven Power
Dual-Plane High-Rise Intake w/180 deg Firing Order
Produces Incredible Top-End Horsepower
Retains Good Throttle Response and Acceleration
Larger Plenum and Runners Maximizes Other Upgrades
Edelbrock Total Power Package Maximizes Gains

from

$32.99

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

Chrome Plated
Grade 5
AN washers with no exposed shoulder for a professional appearance

from

$215.99

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$258.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$235.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$65.99

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Grade 8 Steel

from

$94.99

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$85.09

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features: