Name: Performer 289 Intake Manifold for Small-Block Ford, Black Finish
Brand: Edelbrock
SKU: 21213
Price: 442.99 USD

from

$442.99

Edelbrock part #21213 Performer 289 intake manifold is designed for street 260-289-302 c.i.d. Ford V8’s without EGR. Will not fit Boss 302 or 255 c.i.d. V8’s. Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket

Product Features:

Idle-5500 RPM Range
Dual Plane Type-4150 Style Flange
3.5 in. Front Height, 4.12 in. Center Height, 4.75 in. Rear Height
Black Powder Coated Finish
Made In The USA

from

$60.99

Product Features:

Valve Cover Gasket

from

$67.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
For Engine with One-Piece Fuel Pump Eccentric

from

$429.99

The Edelbrock #38183 is a single-bore 90mm throttle body designed with a 5.0L Ford-style base pad. It is fully machined and assembled by Edelbrock. It includes a Throttle Position Sensor, a progressive throttle cable lever, and cruise and kick-down attach

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$30.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$20.99

Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$52.99

Product Features:

Non-Rotator Type
1.384 in. Outer Diameter
1.020 in. Inner Diameter
1.020 in. Coil Blind
Set of 16

from

$339.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$19.99

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Chrome Plated
This Is A 45 Degree Neck
Comes With O-ring And Bolts
Has Small Hose Fitting On It

from

$237.99

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$43.99

Super Intake Manifold Bolts

from

$58.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$190.99

Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

Product Features:

7.7 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$208.99

Edelbrock part #9655 Pushrods are designed for small-block Ford 289-302 V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precis

Product Features:

6.4 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$381.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$305.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$27.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$38.49

Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Thick parallel ground washer provides more accurate, uniform torque
Hex Prevents Socket Slippage
Accurate And Uniform Torque
Black Plated Finish

from

$1035.99

Product Features:

Complete Single For Flat Tappet
60cc Combustion Chamber Volume
170cc Intake/60cc Exhaust Runner Volume
2.02 in. Intake/1.60 in. Exhaust Valve Diameter
0.625 in. Deck Thickness

from

$284.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$368.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$284.99

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts. Ideal for use with higher compression ratio engines that

Product Features:

Best with aftermarket torque converters and 9.5:1 compression.
Great high RPM power.
Easy on valve train parts.
Can be used with mild ratio rocker arms and traditional performance valve springs.

from

$42.49

Manufactured from high-temperature composite exhaust material. Provides maximum torque retention to eliminate gasket failure. Can be trimmed if necessary for modified port applications. Precision die cut for an excellent fit. For original equipment replacement, high-performance street, drag race and oval track.

Product Features:

Manufactured from high-temperature acrylic blend exhaust material.
Provides excellent sealing and durability.
Can be trimmed if necessary for modified port applications.
For OE replacement, high performance street, drag race and oval track use.

from

$28.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$28.99

Product Features:

Performer Truck Gasket Set
Includes Base To-Upper And Plenum Cover Gaskets

1992 Ford F-250 Pickup Performance Engines

More 1992 Ford F-250 Pickup Performance Engines

Essential 1992 Ford F-250 Pickup Performance Engines

Edelbrock – Performer 289 Intake Manifold for Small-Block Ford, Black Finish (Part No.21213)

Edelbrock – Valve Cover Gasket Set for Ford (Part No.7563)

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7820)

Edelbrock – Throttle Body, 90mm, Pro-Flo XT, Ford-Style, Black Powder Coated Finish (Part No.38183)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2941)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1811)

Mr. Gasket – Timing Cover Gasket Set (Part No.793G)

Edelbrock – Sure Seat Valve Springs for Ford 351W V8 (Part No.5882)

Edelbrock – Performer-Plus camshaft for Small-Block Ford 351W V-8 applications (Part No.2182)

Mr. Gasket – Water Neck (Part No.2662)

Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)

Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1013)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)

Edelbrock – Pushrod Set for Ford 351W (Part No.9659)

Edelbrock – Pushrod Set for Ford 289-302 (Part No.9655)

Edelbrock – Water Pump Ford FE 352-428 1965-76 in Satin Finish (Part No.8805)

Edelbrock – Water Pump Ford 5.0 V8 Reverse Rotation in Satin Finish (Part No.8840)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Mr. Gasket – High Performance Thermostat (Part No.4365)

Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)

Edelbrock – Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02" (Part No.60399)

Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam for Ford 351W (Part No.35-250-4)

Competition Cams – High Energy 206/206 Hydraulic Flat Cam for Ford 429,460 (Part No.34-224-4)

Competition Cams – Magnum/Marine 253/253 Hydraulic Flat Cam for Ford 429,460 (Part No.34-337-4)

Mr. Gasket – Intake / Exhaust Manifold Gasket – Ford 6 Cyl – Includes Necessary Seals And Block-Off Plates (Part No.260)

Edelbrock – Intake Manifold Gasket for 1963-1996 Small-Block Fords (Part No.7220)

Edelbrock – Intake Manifold replacement base and plenum cover gaskets (Part No.3833)

Popular 1992 Ford F-250 Pickup Performance Engines Categories

1992 Ford F-250 Pickup Performance Engines

Performance Engines Brands To Make Your 1992 Ford F-250 Pickup Last

Popular FEL-PRO Performance Performance Engines

Top 1992 Ford F-250 Pickup Performance Engines from Mr. Gasket

FAQs for 1992 Ford F-250 Pickup Performance Engines

What are the most purchased Performance Engines for the 1992 Ford F-250 Pickup?

What are the top-rated 1992 Ford F-250 Pickup Performance Engines?

More Popular Parts for All Makes