1992 Ford E-250 Econoline Performance and Racing Products

Name: Supercoil
Brand: Accel
SKU: 140001
Price: 105.99 USD

Below you will find various in-demand Ford Performance and Racing Products, components and accessories for your 1992 E-250 Econoline. Advance Auto Parts has popular E-250 Econoline parts like Performance Exhaust Products, Performance Distributors, Performance Ignition Products and more. You’ll also find aftermarket and OEM Performance and Racing Products for other E-250 Econoline model years including 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006 and more. Select a category of 1992 Ford E-250 Econoline Performance and Racing Products below and start saving instantly.

Popular 1992 Ford E-250 Econoline Performance and Racing Products Categories

Performance Oil Filters

Performance Engine Coolant Thermostats

Performance Intake Manifolds

Performance Coils

Performance Distributor Cap and Rotor Kits

Performance Shifters

Performance Distributors

Performance Valve Covers

Performance Water Outlets

Performance Radiator Caps

Performance Engine Cylinder Head Gaskets

Performance Engine Camshaft and Lifter Kits

Performance Engine Harmonic Balancers

Performance Ignition Modules

Performance Distributor Components

Performance Engine Intake Manifold Gaskets

Performance Engine Timing Sets and Components

Performance Engine Valve Springs

Performance Engine Valve Cover Gasket Sets

Performance Chassis Bushing Kits

Performance Exhaust Manifold Gaskets

Performance Posi Units and Components

Performance Oil Pans

Performance Distributor Caps

Performance Engine Rocker Arms

Performance Engine Camshafts

Performance Engine Oil Pan Gaskets

Performance Ring and Pinions

Performance Ignition Parts

Performance Intake Manifold Hardware

Performance Sway Bar Link Kits

Performance Sway Bar Bushings

Performance Tie Rod End Boots

Performance Axle Pivot Bushings

Performance Transmission Shift Kits

Performance Engine Cylinder Head Bolts

Performance Engine Push Rods

Performance Engine Cylinder Heads

Performance Torque Converters

Performance Ignition Systems

Essential Performance and Racing Products for 1992 Ford E-250 Econolines

from

$105.99

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

Oil Filled For Better Cooling
Optimized Low Resistance
Silicon Magnetic Steel E-Core
Higher Energy/Voltage Outputs
Quicker Starts
Improved Idle Quality
Resists Shock And Vibration
Resists Corrosion

from

$371.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$373.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$30.19

The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:

Ideal For Tight Spaces
Serrations Prevent Loosening
Flange Distributes Pressure
Zinc Plated Bolts
Grade 5 Material
Easy Installation

from

$605.99

A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$27.99

Product Features:

Firm in the Center Yet Soft on the Outside
Allows Flex and Pivot When Needed

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$237.99

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$28.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$96.99

This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most Ford Thick Film Ignition systems. 1983 thru 1996.

Product Features:

Fits Most Stock And Modified Distributors
Dwell Control Circuit
Resists False Triggering

from

$52.99

MSD molds our most popular V8 distributor caps in-house. These caps are injection molded from DuPont? Rynite material and feature spark plug-style terminals. These terminals offer improved locking connections and the Rynite material is extremely strong with excellent dielectric properties. Plus, most caps have an optional wire retainer that is supplied with these caps to lock the wires in place.

Product Features:

Designed w/Performance In Mind
High Quality Material
Stainless Terminals
Performance replacement part

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$97.99

This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

Product Features:

Relocate oil filter to an easy access location

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$32.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$248.99

Product Features:

FRD 10BLT 8.8 R/P 4.88 MGP

from

$152.99

Use the B&M Transpak to recalibrate your automatic transmission for optimum performance. With the Transpak you will be able to downshift into low at any speed, and keep it in low to any speed that you want.

Product Features:

Recalibrate Auto. Transmission
Optimum Performance
Select Your App. Mode
Improves Transmission Life
Trans. Removal Not Required

from

$229.99

Product Features:

Incredible Improvement in Control
Maintains Proper Caster and Camber Alignment
Increase in Handling and Control
Greatly Reduce Wheel Hop on Quick Acceleration
Even Braking Control is Improved
Better Suspension Stability

from

$51.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$339.99

The Hammer shifter may just be the most comfortable and versatile shifter available. The unique design of the shift handle easily fits all sizes of hands providing the appropriate wrist angle and feel when shifting. The multi-position lockout trigger is s

Product Features:

Ratchet Action Shifter
Cable Operated
Quick Installation
Accurate Shifting
Reverse Lockout Feature

from

$108.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$107.99

Product Features:

Highest Quality Head Bolts
Cold-Formed/Heat Treated
Ensures Molecular Integrity
Reduced Diameter Bolt Heads
Hardened/Parallel-Ground Washers Included
Rated At 170000 psi
Manufactured By ARP

from

$371.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
Accepts Late-Model Choke; Waterneck; and HEI
Accepts A/C And Alternator
Accepts Exhaust Heated Chokes

from

$36.49

Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.

Product Features:

Manufactured from high-temperature acrylic blend exhaust material
Provides excellent sealing and durability
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Precision Die Cut For Excellent Fit

from

$32.99

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$21.79

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

6 3¿8″ diameter
6 3┐8″ diameter
289-302-351 cu. in.
Increased Performance
Set Valve Lash At Proper Time

Upgrade your 1992 Ford E-250 Econoline with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1992 Ford E-250 Econoline, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Performance and Racing Products are key to keeping your E-250 Econoline functioning at its best. At Advance Auto Parts, we offer a wide selection of 77 Performance and Racing Products for the 1992 Ford E-250 Econoline, designed to meet your needs without breaking the bank. From Performance Exhaust Product replacements to Performance Distributors upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1992 Ford E-250 Econoline at great prices. Our Performance and Racing Products inventory for this model ranges from just $9.99 to $1,035.99, with an average price of $243.18. Our 77 Performance and Racing Products in stock come from 11 trusted brands, so you’re sure to find the right part for your 1992 Ford E-250 Econoline without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1992 Ford E-250 Econoline, we stock popular OEM and aftermarket Performance and Racing Products from top names like Mr. Gasket, FEL-PRO Performance, Accel, and more. Mr. Gasket Performance and Racing Products start at just $19.99 and boast an impressive 4 stars average rating from customers. FEL-PRO Performance and Accel also bring quality to the table, with Performance and Racing Products available starting at $32.49, and at an average 4 stars rating. With 364 customer reviews and counting, our 1992 Ford E-250 Econoline Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1992 Ford E-250 Econoline is always ready to roll. We’re committed to providing you with everything you need to keep your E-250 Econoline in top shape, all in one place. Start shopping confidently below for your 1992 Ford E-250 Econoline!

Best-Selling Performance Exhaust Products for 1992 Ford E-250 Econolines

Enhance the driving experience in your Ford with 5 quality Performance Exhaust Product components, starting at $29.49.

show more show less

from

$29.49

Manufactured from high-temperature composite exhaust material. Provides maximum torque retention to eliminate gasket failure. Can be trimmed if necessary for modified port applications. Precision die cut for an excellent fit. For OE replacement, high-performance street, drag race and oval track.

Product Features:

High-Temperature Exhaust Material
Withstands Extreme Exhaust Heat
Excellent Sealing Durability And Torque Retention
Superior Tensile Strength

from

$38.59

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-temperature steel core/graphite faced exhaust material
Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
Conforms to and seals minor surface irregularities
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Anti-Stick Properties
Easy Removal For Disassembly

from

$45.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$36.49

Manufactured from high-temperature acrylic blend exhaust material
Provides excellent sealing and durability
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Precision Die Cut For Excellent Fit

from

$45.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

Most Popular 1992 Ford E-250 Econoline Performance Distributors

Customize your Ford with 11 Performance Distributors products like Performance Distributor Cap and Rotor Kits, Performance Distributor Components, and Performance Distributors, all priced under $691.99.

show more show less

from

$108.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$52.99

Designed w/Performance In Mind
High Quality Material
Stainless Terminals
Performance replacement part

from

$53.09

ACCEL cap and rotor kits offer superior protection from “arc-thru” and crossfire. Features 60k V-rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts and steel rotor springs provide for high spark energy flow.

Product Features:

Features Protection From Arc Thru And Crossfire
Features 60k V Rated Alkyd Compound
Brass Terminals Inserts And Steel Rotor Springs
High Spark Energy Flow

from

$230.99

Everything you need to Super Tune Up your truck, van, or Jeep engine! The kits includes a high performance cap and rotor. A set of 8mm Extreme 9000 Spiral Core wires. This kit also includes the ACCEL classic copper core spark plugs to fire your engine up.

Product Features:

Includes Everything Needed
Resistance High Dielectric Strength Compounds
Race Proven
Improved Performance
Reduced Emissions

from

$691.99

MSD’s Ready-to-Run Ford distributors are the perfect upgrade for bulky Duraspark systems or ancient breaker point models. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance. The billet aluminum housings of these distributors are 5/8 In. smaller in diameter to accommodate induction setups and tight engine compartments. A maintenance-free magnetic pick-up is responsible for triggering the high voltage sparks while a sealed ball bearing guides an oversized shaft. Beneath the bolt down cap and MSD race rotor you’ll find MSD’s accurate mechanical advance assembly. Different advance springs and stop bushings are supplied so you can easily tune a curve to match your needs. Plus, there is a vacuum advance canister to increase economy on long drives.

Product Features:

Equipped w/Steel Gear
CARB E.O. Approved
Does not require an MSD Ignition Control
Supplied w/small dia. cap w/HEI style terminals; race and rotor
Will accept PN[8441] Cap-A-Dapt
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate
Mech. advance assem. can be locked out for crank trigger systems

from

$653.99

The street pro-billet distributors are the perfect choice for powerful engines that see plenty of street time. The street models share the same features as the small diameter models shown above, plus feature a vacuum advance. This canister provides improved economy and an accurate mechanical advance lets you dial-in an advance curve to match your driving needs. A magnetic pick-up produces accurate trigger signals that remain stable throughout the entire rpm range of your engine and is completely maintenance-free.

Product Features:

Billet housing 5/8 in. smaller dia. than stock Ford distributors
CARB E.O. Approved
Easy-to-adjust mech. advance w/supplied springs and stop bushings
Vacuum advance canister for improved economy (can be locked out)
CNC machined billet aluminum housing and billet aluminum base
Maintenance-free magnetic pickup and precision reluctor
Creates stable trigger signals throughout the rpm range
QPQ coated polished steel shaft; guided by sealed ball bearings
Advance plate and weights are fine blanked from chrome moly steel
QPQ coated for friction reduction
Mech. advance assem. can be locked out for crank trigger systems
Advance weight pins are staked and tig welded to the plate

from

$593.99

When you start making serious power with your EFI Ford, the stock distributor shaft is one of the weak links of the engine. These Pro-Billet models answer the need for an affordable replacement in a strong and great looking package. Each distributor starts as a solid billet that is secured into a state of the art computer numerical control (CNC) machine where it is transformed into a precision housing. Inside each housing there is a sealed ball bearing at the top of the shaft. This design is responsible for accurately guiding the oversized polished steel shaft throughout the entire RPM range of your engine. The shaft is also quip-coated for friction reduction and corrosion resistance. The Pro-Billet distributors use a stock-style trigger pick-up to accept factory connectors. For installation, you simply remove the stock distributor and bolt the Pro-Billet MSD in place! Each model is supplied with a special gear to work with the?factory camshafts.

Product Features:

Drop in billet replacement for late model Ford TFI 5.8L dist.
Supplied w/steel gear to work w/factory roller camshafts
Factory style ignition module connector accepts factory wiring
CNC machined billet aluminum housing and billet aluminum base
QPQ coated polished steel shaft; guided by sealed ball bearings
Supplied w/Late Model Distributor Cap And Rotor
Legal to install in all 50 states

from

$489.99

MSD engineers fit all of their high performance distributor experience into a special compact housing designed to be less obtrusive for Ford engines. The diameter of the special cap and housing are 5/8 inch smaller than stock Ford distributors providing extra room in front of the engine. The new MSD cap features spark plug style terminals and is firmly screwed down to the housing. The distributor relies on MSD’s race proven magnetic pick-up and precision reluctor to deliver accurate trigger signals to the MSD ignition throughout high rpm. The reluctor assembly is turned by a hardened steel shaft which rides in a sealed ball bearing for high rpm stability and endurance. Mounted to the top of this shaft is a fully adjustable mechanical advance assembly. The rate at which the chromoly assembly advances the timing is easily controlled by changing the supplied advance springs and stop bushing for total advance.

Product Features:

Billet housing 5/8 in. smaller dia. than stock Ford distributors
Must Be Used w/An MSD Ignition Control
Supplied w/small dia. cap w/HEI style terminals; race and rotor
Will accept PN[8441] Cap-A-Dapt
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate
Mech. advance assem. can be locked out for crank trigger systems
Advance plate and weights are fine blanked from chrome moly steel

from

$483.99

MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:

Same features as PN[8584]
Use w/Edelbrock Victor Jr. man. for add. clearance at water neck
No CARB Exemption Order Number
Maintenance-free magnetic pickup and precision reluctor create stable trigger signals throughout the RPM range
Polished steel shaft is QPQ coated and guided by two sealed ball bearings
Advance weight pins are staked and tig welded to the plate
Supplied with cap-a-dapt and rotor (accepts MSD socket style caps)
Must be used with an MSD Ignition control

from

$103.99

Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

Product Features:

Replacement Distributor Gear

from

$73.29

Replacement Distributor Gear

Top Picks for 1992 Ford E-250 Econoline Performance Ignition Products

Upgrade Ford E-250 Econolines with top-quality Performance Ignition Products parts, including 7 OEM and aftermarket selections for your 1992 model.

show more show less

from

$85.29

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$77.99

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, and crisper throttle response. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

Product Features:

Direct Plug In Replacement Direct OE Fit
Advanced Bobbin Technology
Standard Motor Products SMP Fd-478
MSD 5527
Standard Motor Products SMP Fd-478
MSD 5527
Resists Shock And Vibration
Resists Corrosion

from

$65.99

These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.

Product Features:

Bolt-on Performance
Factory replacement coil

from

$96.99

Fits Most Stock And Modified Distributors
Dwell Control Circuit
Resists False Triggering

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$538.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

Absolutely the most accurate way to trigger the ignition
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.
Incl. brackets/mounting hardware to fit a variety of engines

from

$186.99

Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:

Glass Filled Polyester Case
Longer Spark Duration
Increased Performance
No Energy Loss Due To Arcing
Includes Brass Contact Terminal

In-Demand Performance Engines for 1992 Ford E-250 Econolines

Select from 35 premium Performance Engines parts for your 1992 Ford E-250 Econoline, with prices ranging from $19.99 to $1,035.99.

show more show less

from

$33.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$46.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Rigid core, molded silicone rubber gaskets provide for ease of installation, and are great for on-again/off-again situations (like setting valve lash).
Features high-tech silicone material for long life, a solid steel core for strength and durability, and stainless steel compression limiters to prevent
Not intended for use in emission controlled vehicles.

from

$36.49

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are .187 inch thick.

Product Features:

Manufactured from high-density cork /rubber blend gasket material
A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
For OE replacement, high performance street, drag race and oval track
.187″ thick
Handles Ex Flange Pressure
Forms Leak Proof Seal
Black Latex Coating

from

$26.99

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$55.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$28.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$107.99

Product Features:

Highest Quality Head Bolts
Cold-Formed/Heat Treated
Ensures Molecular Integrity
Reduced Diameter Bolt Heads
Hardened/Parallel-Ground Washers Included
Rated At 170000 psi
Manufactured By ARP

from

$19.99

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers

Product Features:

Hex Head
Zinc Plated
Ideal For Minimal Space
12-Point Head And Flange
Zinc Plated For Protection

from

$237.99

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$111.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$30.19

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$21.79

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

6 3¿8″ diameter
6 3┐8″ diameter
289-302-351 cu. in.
Increased Performance
Set Valve Lash At Proper Time

from

$48.09

Precision die cast, these water necks or thermostat housings are first polished to a high luster, then chrome plated. Comes with gasket and Allen head mounting bolts. Fits 1979-1997 Ford 5.0/5.8L V8s.

Product Features:

Chrome Plated For Great Looks
Includes Gasket & Mounting Bolts

from

$32.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$110.99

Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.brbrA typical MLS head gasket requires a smoother (30Ra) surface finish than composite head gaskets. Mr. Gasket’s proprietary polymer coating will seal a surface finish twice as rough (60Ra) as a typical MLS head gasket. For high performance street, drag race and oval track use.

Product Features:

Gasket bore – 4.030 inch: Compressed thickness – .040 inch
Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
Optimized sealing embossments seals extreme cylinder pressure
Provides excellent stability and reduces cylinder bore distortion.
Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
For high-performance street, drag race and oval track use

from

$35.99

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.brbrFits 1977-1997 Ford Small Block 351 Windsor 2 or 4-barrel.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
Complete with manifold end seals
For OE replacement, high performance street, drag race and oval track use

from

$1035.99

Product Features:

Complete Single For Flat Tappet
60cc Combustion Chamber Volume
170cc Intake/60cc Exhaust Runner Volume
2.02 in. Intake/1.60 in. Exhaust Valve Diameter
0.625 in. Deck Thickness

from

$1035.99

50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Intake Valves Are For Use w/Stock Pistons

from

$1035.99

Product Features:

Capable of 300 plus horsepower when matched with the Edelbrock Performer Power Package
1.90 in. intake valves are for use with stock pistons
Exhaust valve is 1.60 in.
60cc combustion with 170cc intake port
Flat Tappet Camshaft Type

from

$966.99

50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Hand-Blended Intake and Exhaust Bowls
CNC-Matched Intake/Exhaust Ports in Std Location
Thicker Deck Surfaces than Other Brands
Heli-Coils in Rocker Studs and Exhaust Bolt Holes

from

$893.99

Product Features:

Made of aluminum with a natural finish
60cc chambers with 170cc intake ports
2.02 in. intake and 1.60 in. exhaust valves
Includes intake valves, exhaust valve, valve springs, retainers, locks, guide plate and valve stem seals
Does not include damper spring, rocker arms, nuts and drilled steam holes

from

$772.99

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Improve performance on the street or race track. Larger cross-sectional area and taller card flange. Compatibility with lar

Product Features:

Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed For 1500 To 6500 RPM
Designed For Street And High Performance
Larger Cross Sectional Area
Taller Carb Flange
Compatibility w/Large Displacement 351W Based Eng.

from

$692.99

50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Intake Valves Are For Use w/Stock Pistons

from

$605.99

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$594.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Hand-Blended Intake and Exhaust Bowls
CNC-Matched Intake/Exhaust Ports in Std Location
Thicker Deck Surfaces than Other Brands

from

$468.99

Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed For 1500 To 6500 RPM
Designed For Street And High Performance
Larger Cross Sectional Area
Taller Carb Flange
Compatibility w/Large Displacement 351W Based Eng.

from

$427.99

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Ford V8 289-302-351W applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
Designed for high performance street and race engines
Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
Additional clearance, up to 1.650″ O.D. valve spring

from

$373.99

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$339.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$284.99

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$190.99

Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

Product Features:

7.7 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$44.99

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$43.99

Super Intake Manifold Bolts

from

$38.59

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use
Creates Tight Leak proof Seal

from

$29.99

Product Features:

Timing Chain Only

Most Sold 1992 Ford E-250 Econoline Performance Oil Filters

Explore our best-selling Ford parts for the 1992 E-250 Econoline among 1 OEM and aftermarket options starting from $97.99.

show more show less

from

$97.99

Relocate oil filter to an easy access location

Top-Rated Performance and Racing Products Brands For Your 1992 Ford E-250 Econoline

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1992 Ford E-250 Econolines. Below you’ll find some of our best rated Performance and Racing Products from Mr. Gasket, FEL-PRO Performance, and Accel, and more. Performance and Racing Products from these brands that fit a 1992 E-250 Econoline start at just $19.99 and are rated as high as 4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular Mr. Gasket 1992 Ford E-250 Econoline Performance and Racing Products

When it comes to maintaining or upgrading your 1992 Ford E-250 Econoline, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Mr. Gasket ticks all of those boxes. We offer a wide selection of Mr. Gasket Performance and Racing Products, specifically designed for the 1992 Ford E-250 Econoline. With over 17 Mr. Gasket brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $19.99, with an average price of just $45.08. Plus, with over 27 customer reviews and an average rating of 4 stars, you can trust that our Mr. Gasket Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$30.19

This product is not rated

Valve Cover Gasket Set

“”

from
$48.09

This product is not rated

Thermocap Radiator Cap

“”

from
$21.79

This product is not rated

Precision Timing Tape

“”

Popular FEL-PRO Performance 1992 Ford E-250 Econoline Performance and Racing Products

FEL-PRO Performance auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1992 Ford E-250 Econoline owner should feel confident when installing genuine FEL-PRO Performance parts in their vehicle. To ensure the best fit and performance for your 1992 E-250 Econoline, Advance Auto Parts carries a full inventory of 6 FEL-PRO Performance Performance and Racing Products. Plus you will be keeping your Ford in peak condition while saving money because prices on these FEL-PRO Performance Performance and Racing Products range from $32.49 to $55.99, plus, with more than 7 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

from
$32.49

This product is not rated

Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set

“”

from
$45.99

This product is not rated

Exhaust Manifold Gasket Set

“”

from
$45.99

This product is not rated

Exhaust Manifold Gasket Set

“”

FAQs for 1992 Ford E-250 Econoline Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1992 Ford E-250 Econolines?

Out of 77 Performance and Racing Products that fit 1992 Ford E-250 Econolines, the following parts are the top sellers:

High Performance 180 Degree Thermostat for Increased Flow (17360033) – $26.99
Lower Intake Manifold Gasket Set: 11 Piece Set (5991277) – $33.99
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (5990467) – $55.99

What’s the price range for 1992 Ford E-250 Econoline Performance and Racing Products?

Performance and Racing Product prices for the 1992 Ford E-250 Econoline start at $9.99 and go up to $1,035.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1992 Ford E-250 Econoline?

The average price for Performance and Racing Products for the 1992 Ford E-250 Econoline is $243.18. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Ford E-250 Econoline model years?

Yes, we currently carry Performance and Racing Products for 31 model years of Ford E-250 Econolines between 1975 and 2006. Performance and Racing Products are bought most frequently for the following model years: 2006, 2005, 2004, 2003, 2002, 2001, 2000, 1999, and 1998.

What are the cheapest Performance and Racing Products for my 1992 Ford E-250 Econoline?

The cheapest 1992 Ford E-250 Econoline Performance and Racing Products we carry in stock are:

Tie Rod Dust Boot (17360821) – $9.99
Sway Bar Bushing Set (22908461) – $13.99
Intake Manifold Bolts (17360287) – $19.99
Precision Timing Tape (17360126) – $21.79
High Performance 180 Degree Thermostat for Increased Flow (17360033) – $26.99

What types of Performance and Racing Products do you sell for my 1992 Ford E-250 Econoline?

As of 2/5/25, these are some of the most in-demand types of Performance and Racing Products for a 1992 Ford E-250 Econoline:

Can I get help with 1992 Ford E-250 Econoline Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Performance and Racing Products and more.

What is your return policy for Ford E-250 Econoline Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Ford E-250 Econoline Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1992 Ford E-250 Econoline Performance and Racing Products

Accel – Supercoil (Part No.140001)

Powertrax – Lock Right Locker (Part No.1822-LR)

Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam and Lifter Kit (Part No.CL35-250-4)

Mr. Gasket – Oil Pan Bolt Kit (Part No.6087)

B & M – Torque Converter, Tork Master 2400 (Part No.40438)

Energy Suspension – Axle Pivot Bushing Set (Part No.4.3121R)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1812)

Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)

Edelbrock – Intake Manifold Gasket for 1963-1996 Small-Block Fords (Part No.7220)

Accel – Ford Tfi Modulator 1983-96 (Part No.35368)

MSD Ignition – Distributor Cap; Ford HEI (Part No.8408)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1614)

Mr. Gasket – Remote Oil Filter Kit (Part No.7682)

Mallory – Unilite Ignition Module (Part No.605)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)

Energy Suspension – Sway Bar Bushing Set (Part No.4.5102G)

Motive Gear – Performance Differential Ring and Pinion (Part No.F888488)

B & M – Transpak, 67-91 C6 Transmission (Part No.40228)

Energy Suspension – Hyper-Flex System (Part No.4.18116G)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-1)

B & M – Automatic Shifter, Hammer Shifter, Universal (Part No.80885)

Accel – Distributor Cap And Rotor Kit (Part No.8230)

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

Edelbrock – Performer 460 EGR Intake Manifold Big-Block Ford (Part No.3766)

Mr. Gasket – Exhaust Gasket Set (Part No.264G)

Energy Suspension – Sway Bar Bushing Set (Part No.4.5107G)

Mr. Gasket – Precision Timing Tape (Part No.1594)

Mr. Gasket – Exhaust Gasket Set (Part No.253)

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5928)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1467)

Mr. Gasket – Exhaust Gasket Set (Part No.264G)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1468)

Accel – Distributor Cap And Rotor Kit (Part No.8230)

MSD Ignition – Distributor Cap; Ford HEI (Part No.8408)

Accel – High-Performance Distributor Cap & Rotor Kit (Part No.8233)

Accel – Tst Ford 84-97 5.8L 85-88 5.0L (Part No.TST15)

MSD Ignition – Distributor; Ford 351W; Ready-to-Run; with Steel Gear (Part No.83541)

MSD Ignition – Distributor; Ford 351W; Vacuum Advance (Part No.8478)

MSD Ignition – Distributor; Ford TFI; 351W (Part No.8453)

MSD Ignition – Distributor; Ford 351W; Pro-Billet; Small Cap (Part No.8578)

MSD Ignition – Distributor; Ford 351W; with Edelbrock Victor Jr (Part No.85805)

Mallory – Distributor Drive Gear (Part No.29432)

Mallory – Distributor Drive Gear (Part No.29421PD)

Mallory – Unilite Ignition Module (Part No.605)

Accel – Ford 1984-98 Eec-Iv Supercoil (Part No.140012)

MSD Ignition – Coil; Street Fire; Ford TFI (Part No.5527)

Accel – Ford Tfi Modulator 1983-96 (Part No.35368)

Mallory – Distributor Wiring Harness (Part No.29349)

MSD Ignition – Crank Trigger Kit; Big Block Ford (Part No.8644)

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 11 Piece Set (Part No.1250)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1684)

Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5870)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-2)

Edelbrock – Intake Manifold Gasket for 1963-1996 Small-Block Fords (Part No.7220)

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

Mr. Gasket – Intake Manifold Bolts (Part No.958G)

Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Mr. Gasket – Valve Cover Gasket Set (Part No.276)

Mr. Gasket – Precision Timing Tape (Part No.1594)

Mr. Gasket – Water Neck (Part No.9713)

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1820)

Mr. Gasket – Mls Head Gasket (Part No.3175G)

Mr. Gasket – Intake Gasket (Part No.223)

Edelbrock – Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02" (Part No.60399)

Edelbrock – Performer Small-Block Ford 1.90" Cylinder Head Hydraulic Flat Tappet (Part No.60329)

Edelbrock – Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90" (Part No.60379)

Edelbrock – Performer Small-Block Ford 1.90 Cylinder Head Flat Tappet Springs, Polished (Part No.603219)

Edelbrock – Performer Small-Block Ford 2.02" Cylinder Head Hydraulic Flat Tappet (Part No.60359)

Edelbrock – RPM Air-Gap Small Block Ford Polished Intake Manifold (Part No.75811)

Edelbrock – Engine Cylinder Head (Part No.60319)

B & M – Torque Converter, Tork Master 2400 (Part No.40438)

Edelbrock – Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02" Bare (Part No.60389)

Edelbrock – RPM Air-Gap Small Block Ford 351W Intake Manifold (Part No.7581)

Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud (Part No.19043-16)

Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam and Lifter Kit (Part No.CL35-250-4)