1991 Toyota Pickup Drivetrains
More 1991 Toyota Pickup Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1991 Toyota Pickup, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1991 Toyota Pickup Drivetrains
Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)
from
$44.99
3 Qt. Penzoil 80W90 conventional gear Oil.
Product Features:
See More
Product Features:
- Includes three quarts of conventional oil
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.8533)
from
$81.99
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to TOYOTA 89-95;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1989-1995
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.1811 INCH / 30 MM
- CENTERLINE: 2.75 INCH / 70 MM
- MOUNT WIDTH: 9.00 INCH / 229 MM
Yukon Gear – 1541H Alloy Rear Axle For ’86-’95 Toyota Pick And 4Runner (Part No.21659)
from
$284.99
Yukon 1541H alloy rear axle for ’86-’95 Toyota Pick and 4Runner with length 28 1/2″ and 30 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a five year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- 30 spline
- 6 lug
- 28.5″ long
- Fits Toyota 8″ and V6 in 1989-1995 Pickup and 4Runner
Yukon Gear – Inner Stub Shaft Bearing For Toyota 7.5" IFS (Part No.18061)
Rugged Ridge – Locking Hub (Part No.15001.21)
from
$244.99
Approved as original equipment by vehicle manufacturers and militaries world wide, these tough hubs are built to last. A hardened nylon center is used instead of metal to keep you moving in the rare case of a hub failure. The only way to repair it is to r
Product Features:
See More
Product Features:
- Impact Resistant Nodular Iron
- Corrosion Resistant
- Better 4WD Performance
- Better Fuel Economy
- Easy Install
Yukon Gear – Bearing Race Driver (Part No.56004)
from
$99.99
Bearing race driver for Toyota front V6, Landcruiser reverse rotation, and Tacoma with locker (TOY30025). No return.
Product Features:
See More
Product Features:
- Bearing race driver
- Fits 30025 race
- All steel construction
National – Bearings (Part No.15245)
from
$9.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
National – Multi Purpose Bearing (Part No.HB-24)
from
$227.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Controlled heat treating process for lasting performance and extended bearing life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Toyota Bearing Retainer For ’01-’02 4Runner, ’01-’04 Tacoma & 00-’06 Tundra (Part No.33421)
from
$22.99
Product Features:
See More
- Bearing retainer
- Fits 2001-2002 Toyota 4Runner, 2001-2004 Tacoma and 2000-2006 Tundra
Cardone – Front Drive Shaft: Not Greasable, Direct Replacement (Part No.65-9375)
from
$736.99
CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.
Product Features:
See More
Product Features:
- Built to match O.E. form, fit and function.
- 100% NEW universal joints are installed to ensure proper fit and optimal performance.
- All slip yokes are lubricated to prevent premature wear.
- Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.
Yukon Gear – Toyota 8" & V6 Gasket (Part No.23028)
Yukon Gear – Pinion Seal For Toyota 7.5", 8", V6 & T100 (Part No.30005)
from
$19.99
Pinion seal for 7.5″, 8″, V6, and T100 and Tacoma with lockers.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Pinion seal
- Fits Toyota 7.5″, 8″ with 4 cylinder engine, V6, Landcruiser and Tacoma/T100 with factory locking differential
Yukon Gear – Yoke For Toyota V6 Rear With 29 Spline Pinion (Part No.41206)
from
$123.99
Product Features:
See More
- Fits Toyota V6 rear
- Conversion yoke for 29 spline gears
- 29 spline pinion
Yukon Gear – 8" Roll Pin, Solid (Part No.33412)
USA Standard Gear – Spartan Spring & Pin Kit, Fits Smaller Designs (Part No.17011)
from
$26.99
Spartan spring & pin kit, fits smaller designs.
Product Features:
See More
Product Features:
- Replacement spring and pin kit for Spartan Locker
- Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
- Includes 4 springs and 4 alignment pins
National – Bearings (Part No.JLM104948)
from
$24.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Zip Locker For Toyota V6 (Part No.34034)
from
$1356.99
The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.
Product Features:
See More
Product Features:
- Fits Toyota V6 rear
- Forged case and 8620 internals for added strength
- Works with a variety of air delivery systems
- Assembled in the USA
Yukon Gear – Toyota 8" & V6 Pinion Nut Washer (Part No.33168)
from
$16.99
Toyota 8″ & V6 pinion nut washer.
Product Features:
See More
Product Features:
- Pinion nut for Toyota 8″ and V6
Yukon Gear – Steel Spool For Toyota V6 (Part No.32051)
from
$364.99
Yukon Performance 10 bolt steel spool for V6 Toyota with 30 spline axles. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Toyota V6 rear
- Provides 100% traction to both wheels at all times
- Not recommended for street driven vehicles
Yukon Gear – Bearing Install Kit For Toyota 7.5" (With Four-Cylinder Only) IFS Differential (Part No.11086)
from
$344.99
Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.
Product Features:
See More
Product Features:
- Fits standard rotation Toyota 7.5″ front with 4 cylinder engine
- Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.
Yukon Gear – 12 Hole Yoke For ’83 And Newer Toyota 8" And V6 With 27 Splines (Part No.41105)
from
$109.99
Yukon 12 hole yoke for ’83 and newer Toyota 8″ and V6 with 27 splines. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Toyota 8″ and V6
- 27 spline
- Round companion flange
Yukon Gear – Toyota 7.5", 8", & V6 Ring Gear Bolt Retainer Plate (Part No.33061)
from
$6.99
Toyota 7.5″, 8″, & V6 ring gear bolt retainer plate (5 needed).
Product Features:
See More
Product Features:
- Ring gear bolt retainer plate for Toyota 7.5″ 8″ and 8″ V6
- 5 needed
Motive Gear – Differential Gear Install Kit (Part No.TOYV6IK)
National – Bearings (Part No.LM102910)
from
$6.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Spicer – SPICER U-JOINT (Part No.5-1310-1X)
from
$44.99
SPICER U-JOINT
Yukon Gear – V6 Side Gear Thrust Washer (Part No.33391)
from
$23.99
V6 side gear Thrust washer.
Product Features:
See More
Product Features:
- Side gear thrust washer
- Fits Toyota V6
EMPI – RE CV Joint Boot Kit (Part No.K6010182648EMP)
from
$26.96
The EMPIRE CV Joint Boot Kit is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function. Install one boot kit per wheel to restore vehicle to optimal condition and protect the constant velocity joint from contamination
Product Features:
See More
Product Features:
- Help restore the vehicle to like-new condition
- Constructed of high strength OE materials
- Resists environmental contamination
- Protects the CV joint from premature failure
National – Shaft Repair Sleeve (Part No.99166)
from
$34.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
Popular 1991 Toyota Pickup Drivetrains Categories
1991 Toyota Pickup Drivetrains
You count on your 1991 Toyota Pickup to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 274 Drivetrains ranging in price from $2.29 to $1,356.99, you’re sure to find everything you need for your 1991 Toyota Pickup.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 20 different brands like Valvoline, National, and Spicer. 1991 Toyota Pickup Drivetrains start as low as $2.29!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 2,879 extensive product reviews on 1991 Toyota Pickup Drivetrains. Some of the top-rated Drivetrains products we carry are Uni-Fit C.V. Joint Boot Kit Outer greater than 3.58 In. Diameter with 3.3 stars and CV Axle Shaft Assembly with 4.6 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1991 Toyota Pickup below to get started!
Top-Rated Drivetrains Brands For Your 1991 Toyota Pickup
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1991 Toyota Pickup running right for years to come. In our inventory you’ll find brands like Valvoline, National, Spicer, and even more.
Popular Felpro Drivetrains
You’ll find popular Felpro brand products across Differentials. All are waiting to get your 1991 Toyota Pickup back on the road. Some of the top-rated Felpro products in these categories are:
Top-Rated Drivetrains
If are what you’re looking for, our inventory holds plenty. We stock brand Drivetrains for your 1991 Toyota Pickup, and some of our most reviewed parts include:
from
$12.79
(446)
MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart
Differential Oil
FAQs for 1991 Toyota Pickup Drivetrains
What are the most purchased Drivetrains for the 1991 Toyota Pickup?
Out of 274 Drivetrains for the 1991 Toyota Pickup, the most popular in our inventory are:
What are the top-rated 1991 Toyota Pickup Drivetrains?
Top-rated Drivetrains for your 1991 Toyota Pickup based on customer reviews/ratings are:
from
$32.99
(18)
Uni-Fit C.V. Joint Boot Kit Outer greater than 3.58 In. Diameter
“Well built , with grease fittings. Good OEM alternative!! Recommend!!”
from
$132.99
(14)
CV Axle Shaft Assembly
“Axle appears to be identical to OEM. Joints are nice and tight. Boots and bands appear to be quality material. Only time will tell how they hold up.”
from
$29.99
(8)
Uni-Fit C.V. Joint Boot Kit Inner Greater Than 3.35 In. Diameter
“Worked great. Direct fit.”
