from

$9.99

New Standard Replacement Fuel Tank Lock Ring, Includes O-Ring

Product Features:

Includes O-Ring
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$392.99

100 years of OE experience, supplier to the world’s top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.

Product Features:

Delphi is a global OE manufacturer and all fuel pumps are built to Delphi’s OE standards
Delphi pumps are designed to operate under extreme temperatures with quick engine starts and to avoid low-fuel hesitation, including alcohol fuels and blends
Metal tubes in Delphi hangers are routed so as to not contact the tank or vehicle underbody at any point eliminating noise and vibration during vehicle operation
Empty float height and float retention matches OE specifications and guarantees correct gas gauge reading
Restores fast pressure performance and system integrity, translating to better pumping through less energy
Lower failure rates due to its innovative design and durability
Part is validated, tested and matched to the right vehicle application
Lower amperage draws less load on vehicle’s electrical system
Always be sure to check and clean fuel tank to avoid unnecessary returns

from

$38.43

ACDelco GM Original Equipment Temperature Sensors are GM-recommended replacements for your vehicle’s original components. It senses the temperature of various liquids for a variety of components including radiator cooling fans, temperature gauges, and warning indicators. Typically, the temperature sensor sends a signal to the control module and the control module then controls the on/off function of another component. These original equipment multi-purpose temperature sensors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

Helps keep engine operating at proper temperature
Sends accurate temperature readings to the gauge
GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$27.99

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

100% pure copper windings in primary and secondary bobbins improve durability and provide higher resistance to internal shorts and dielectric breakdown
Electronic ignition module profile and feedback signal ensures proper OE fit, form, and function
Thermoplastic housing withstands heat stress for enhanced durability
Internal core made from grain-oriented electrical steel limits loss factor within magnetic circuit to reduce heat that may reduce coil endurance
External core made from oriented silicon steel ensures durability and longevity

from

$84.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$435.99

ACCEL Performance fuel injectors provides precise control of fuel delivery & atomization for improved throttle response. They are all new units: not modified stock units or remanufactured from used cores. They feature a low-mass disc design that ensures accurate metering control even at ultra-low & high duty cycles and higher fuel pressures. ACCEL performance Injectors can be used with gasoline or E85 and are great for blown applications where increased fuel pressure and precise metering are required. State-of-the-art manufacturing processes reduce flow deviations between injectors, which improve performance. Low- and High-impedance designs are available to match most commercial applications.

Product Features:

Provides precise control of fuel delivery & atomization for improved throttle response
All new units: not modified stock units or remanufactured from used cores
New low-mass disc design ensures accurate metering control even at ultra-low & high duty cycles
Operates at higher fuel pressures without loss of metering control
Great for blown applications where increased fuel pressure and precise metering are required
State-of-the-art manufacturing processes reduce flow deviations between injectors to improve performance
Accurate Metering Control Even At Ultra-Low And High Duty Cycles

from

$88.99

Innovative engineering, manufacturing technology and quality control ensure that Spectra Premium fuel tank filler necks meet or exceed the performance of the original equipment they replace.

Product Features:

Unit is designed to OE fit, form and function requirements accomplished by leveraging our OE fuel system design expertise
Unit is dual coated for enhanced corrosion protection
Fit tested on the very same vehicle application for which it was developed verifying first-hand that the design fits properly and can be easily installed
Unit is leak tested after production to ensure product in free from fuel and / or evaporative leaks
Tested with OE fuel cap to prevent evaporative emission and check engine light failure

from

$7.29

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

Designed to OE standards for ease of installation
State-of-the-art designs that meet or exceed OE specifications
Top-of-the-line quality and performance
With industry leading expertise, when original equipment fails our products are designed to fix the inherent failure issues
BWD is a global manufacturer of original equipment and aftermarket fuel injection products, complete quality control is maintained through the manufacturing process from componentry to finished product

from

$27.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$3.49

GM Genuine Parts Multi Purpose Seals are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$7.49

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$195.99

Innovative engineering, manufacturing technology and quality control ensure that Spectra Premium fuel tanks meet or exceed the performance of the original equipment they replace.

Product Features:

Unit is designed to OE fit, form and function requirements accomplished by leveraging our OE fuel system design expertise
Lock ring included with each tank to reduce installation time and to ensure a complete repair
Made with corrosion resistant, OE approved, Ni Terne steel for durability
Unit is leak tested after production to ensure product in free from fuel and / or evaporative leaks
Each new fuel tank is road tested to ensure real world performance and to verify that each design meets our high standards for quality
Engineered to stringent tolerances based on our Canadian engineers’ in-depth knowledge of the OE part it’s designed to replace
Fit tested on the very same vehicle application for which it was developed verifying first-hand that the design fits properly and can be easily installed
Packaged with double-layered foam wrap and heavy-gauge corrugated board to ensure product quality at installation

from

$3.49

GM Genuine Parts Vacuum Check Valves are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
Original equipment parts are designed to work with your GM vehicle safety systems — aftermarket replacement parts may not meet the same OE safety regulations, depending on the part type
GM regularly updates production and service part designs to integrate new materials and technologies

from

$61.99

The EGR system is an emission control device designed to recirculate exhaust gas into the engines air intake system and back to the combustion chamber to control nitrogen oxides or NOx. The chemical NOx is created when oxygen and nitrogen are heated above 2,800-degree F. Exhaust gas, or gas that is displaced from the combustion chamber, contains little to no oxygen molecules. By recirculating this gas back into the combustion chamber fewer oxygen molecules are available for the combustion event which will therefore create a cooler combustion event. The EGR valve can be actuated by engine vacuum or electronically by the engine control module.

Product Features:

Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Our EGR valves are designed to match the vehicle specific exhaust gas flow rate as designed by the engine manufacturer to provide clean tail pipe emissions.
Feedback EGR valves and pressure sensors contain a robust circuit board design which increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
Where applicable stainless-steel sleeves used over cold rolled sleeves providing smooth EGR pintle operation under all operating conditions.

from

$30.49

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

Premium quality materials for longer service life
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$31.99

100 years of OE experience, supplier to the world’s top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.

Product Features:

Filtration performance and micron rating meet or exceed OE requirements
OE replacement strainer designed for use with Delphi electric fuel pumps
Replacing the strainer is always recommended when replacing a fuel pump

from

$65.05

Driveworks® offers a line of aftermarket parts and accessories that are commercially acceptable and competitively priced, which provides professional technicians and DIYers with an affordable alternative for repairs.

Product Features:

Direct-fit OE replacement ensures ease of installation
Designed to meet OE performance
As the leader in commercially acceptable parts, we provide professional technicians with the quality parts they need
As the leader in commercially acceptable parts, we provide professional technicians with the quality parts they need

from

$12.49

To perform a complete fuel pump replacement, clean the tank every time. Order the Delphi Fuel Tank Cleaning Kit (Part FC01). Remember, the original pump went into a clean fuel tank, to ensure the same level of performance, the new pump should too. 100 ye

Product Features:

Helps avoid premature fuel pump failure
Lint free towel included
Low suds formulation
Removes harmful contaminants from the fuel tank

from

$15.99

Fuel Cap Tester Adaper for use with Stant fuel cap testers. Color coded for easy identification. Made of durable plastic.

Product Features:

BAR Certified adapters
Adapter check’s a fuel cap’s ability to hold pressure.
Adapters meet EPA standards for recommended fleet coverage.
Check adapter application chart for specific makes and models

from

$10.29

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

Premium quality materials for longer service life
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$7.99

This engine crankcase breather hose is designed to match the fit and function of the original hose on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this engine crankcase breather hose is designed to match the fit and function of the original hose on specified vehicle
Restores functionality – reliable replacement for an original hose that has failed due to pressure, heat and cracking
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$102.13

For more than a century, Delphi has been making the parts cars are born with. Delphi is proud of its OE heritage, and over the years they have used that experience to expand into a global aftermarket supplier.

Product Features:

Corrosion resistant housing material
Premium materials for longer service life
Meets or exceeds OEM specifications

from

$59.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$39.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$16.16

Recommended for replacement whenever the sending unit is serviced, Dorman’s Fuel Tank Sending Unit Lock Ring securely retains the fuel pump assembly to the lock. Its heavy-duty steel or plastic construction ensures a long life.

Product Features:

Comes with rubber seal or gasket
Direct replacement for a proper fit every time
Corrosion-resistant
Quality-tested for trouble-free performance

from

$71.99

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

Designed to OE standards for ease of installation
Application-specific to ensure the proper fit and form
Precision-engineered pressure regulators for proper fuel delivery and engine performance
As a global manufacturer, we have complete control of the manufacturing process, from components to finished product?

from

$4.29

Product Features:

Premium OE quality materials

from

$23.99

Experience uncompromising quality and emissions compliance with these tethered fuel caps. Manufactured with top-tier materials and rigorous production and safety standards adhering to Original Equipment Manufacturer guidelines. Designed meticulously to meet both state and federal emissions requirements, it ensures environmental responsibility. With its specifically engineered pressure and vacuum relief valves, fuel evaporation becomes a thing of the past. Bid farewell to the risk of losing up to 30 gallons of precious gasoline over a year due to a leaking fuel cap. Trust in our superior construction to safeguard your fuel and contribute to a greener future.