1991 Chevrolet Corvette Performance and Racing Products

Below you will find various in-demand Chevrolet Performance and Racing Products, components and accessories for your 1991 Corvette. Advance Auto Parts has popular Corvette parts like Performance Fuel Systems, Performance Oil Filters, Performance Exhaust Products and more. You’ll also find aftermarket and OEM Performance and Racing Products for other Corvette model years including 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019 and more. Select a category of 1991 Chevrolet Corvette Performance and Racing Products below and start saving instantly.

Popular 1991 Chevrolet Corvette Performance and Racing Products Categories

Performance Oil Filters

Performance Starters

Performance Intake Manifolds

Computer Chip Programmers

Performance Fuel Pumps

Performance Air Filters

Performance Coils

Performance Computer Prom and Chips

Performance Shifters

Performance Distributors

Performance Transmission Dipstick Tubes

Performance Valve Covers

Performance Exhaust System Kits

Performance Engine Water Pumps

Performance Radiator Caps

Performance Engine Cylinder Head Gaskets

Performance Distributor Components

Performance Engine Intake Manifold Gaskets

Performance Engine Timing Sets and Components

Performance Engine Valve Springs

Performance Engine Valve Cover Gasket Sets

Performance Chassis Bushing Kits

Performance Flywheel and Flexplates

Performance Exhaust Manifold Gaskets

Performance Posi Units and Components

Performance Oil Pans

Performance Timing Covers and Tabs

Performance Leaf Spring Bushings

Performance Valve Cover Hardware

Performance Upper Performance Control Arm Bushings

Performance Engine Rocker Arms

Performance Universal Joints

Performance Engine Oil Pan Gaskets

Performance Ignition Parts

Performance Intake Manifold Hardware

Performance Sway Bar Link Kits

Performance Sway Bar Bushings

Performance Engine Main Bearing Gasket Sets

Performance Brake Bleeders

Performance Tie Rod End Boots

Performance Oil Filler Caps

Performance Strut Rods and Kits

Performance Engine Cylinder Head Installation Kits

Performance Ball Joint Boots

Performance Engine Timing Cover Gasket Sets

Performance Engine Push Rods

Performance Engine Cylinder Heads

Performance Nitrous Systems

Nitrous Oxide Injection System Kit

Performance Torque Converters

Performance Ignition Systems

Performance Engine Valve Spring Retainer

Performance Transmission Rebuild Kits

Essential Performance and Racing Products for 1991 Chevrolet Corvettes

from

$206.99

Keith Dorton Series VoluMax race series fuel pump made from heavy duty construction for continuous high RPM operation. Redesigned high flow valves always ensure adequate fuel delivery. Fuel pressure regulator is required. Fuel body casting can be rotated

Product Features:

High Output Fuel Flow
Flows 170 gph Free Flow
Shutoff Pressure Pre-Set At 8 PSI
Fuel Pressure Regulator Required Recommend P/N 12-704
Heavy Duty Construction For Continuous High rpm Operation
Redesigned High Flow Valves Ensure Adequate Fuel Delivery
Fuel Body Casting Can Be Rotated For Plumbing Situations
3/4in.-16 Inlet And Outlet Ports

from

$79.99

Lakewood universal replacement U-joints are fatigue- and wear-resistant, the ultimate in strength. Designed with ultra-durable chrome-nickel-moly alloy cross and caps, and special high-carbon steel and induction heat-treated needle bearings.

Product Features:

Chrome-Nickel-Moly Alloy Cross
Improved Fatigue Resistance
High-Carbon Steel Bearings
Maximize Wear Resistance
Solid Forged Cross Body
High Strength

from

$415.99

Product Features:

Designed for 1500 to 6000 RPM Performance
Manifold has a Balanced 180+ Firing Order
Smooth and Consistent Part-Throttle Power
Makes +25 HP over Edelbrock Torker II
Makes +30 ft/lbs of Torque over Performer
Includes Metering Rods to Calibrate Edelbrock PN #
Carburetor Center-to-Center Dimensions = 6-7/16 in
For 1975 and Earlier and Large Oval-Port Heads

from

$72.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$1009.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
64cc Combustion Chambers Improve Performance
Retain Stock Compression Ratio

from

$333.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$299.99

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$18.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$544.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$147.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

Complete Kit: Includes Retainers And Locks
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Includes Superior Quality Steel Retainers
Includes 7 deg. Heat-Treated Valve Stem Locks
Retainers and Locks Black Oxide Coated
Dyno Tested And Street Proven
Great Match to Edelbrock Camshaft Kit

from

$21.99

Adds a dramatic amount of performance and durability to any vehicle, cars, trucks and SUVs. Helps the vehicle be in control – when maneuvering through turns, during standing start accelerations, braking, even over bumps and berms. Made of Energy’s Hyper-Flex performance polyurethane which lasts 5 -10 times longer than conventional rubber components.

Product Features:

Made of Superior Hyper-Flex+ Material
Adds Dramatic Amount of Performance/Durability
Helps Vehicle Be in Control
Allows the Suspension to Function Properly

from

$373.99

Product Features:

Incredible Improvement in Control
Maintains Proper Caster and Camber Alignment
Increase in Handling and Control
Greatly Reduce Wheel Hop on Quick Acceleration
Even Braking Control is Improved
Better Suspension Stability

from

$684.99

Product Features:

Designed For Carbureted V6 And V8 Engines
Use With Single Or Dual Plane Manifolds
Power Increases From 50 to 100 HP
Plate Systems are Easy to Install
Precision EDM Machined Spray Bars Maximize Flow
Option of Silver Powder Coated or Polished Bottle
Recommend Ignition Retard ; Upgraded Fuel System
Requires Use of Premium Fuel

from

$203.99

Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:

7.25 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$461.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

6.25 in. Diameter
Absolutely the most accurate way to trigger the ignition.
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.

from

$23.99

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

Repairs That Leaky Rear Main Sail
Silicone Rubber to Withstand Extreme Engine Oil Temperatures
Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
Injection Molded for Precise Fit

from

$242.89

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

Designed For Daily Street Driving
For Unmodified Vehicles w/Stock Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$17.79

Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$95.99

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

Valve Spring Retainers for Use OE Cast Iron Heads
Superior Quality Heat-Treated Steel
Machined for Strength with Black Oxide Finish
Finish Ensures Rust and Corrosion Protection

from

$614.99

Corvette owners can now replace their worn out magna-pulse distributors with this precision pro-billet tach drive distributor. Advantages such as an accurate magnetic pick-up, oversized shaft, vacuum advance and a billet aluminum housing are just a few of the MSD advantages. Inside the billet housing, a sealed ball bearing and long sintered bushing guide a 0.500 inch steel shaft for high rpm accuracy. A special reluctor is mounted to this shaft and is responsible for triggering the magnetic pick-up. An adjustable mechanical advance assembly allows you to get the most performance out of your Vette’s engine by custom tailoring a timing curve to fit your application. The tach drive assembly is compact to clear the firewall and linkage. It can be repositioned easily to fit different applications plus has a grease fitting for lubrication.

Product Features:

Same Features As PN[8571] w/The Addition Of A Vacuum Advance
CARB E.O. Approved

from

$79.99

Billet aluminum handle with flexible braded steel tube mounts to the firewall. 29-3/4 inch long.

Product Features:

Braided Stainless Steel
Firewall Mounting
Includes Oil Fill Tube

from

$14.99

Spectre’s Valve Cover Hold Downs feature high quality steel construction with a triple chrome-plated finish. Manufactured for an optimum fit, this product’s hex heads include a decorative O-ring cap for a customizable appearance to suit your needs. Sold 4 per package, these studs are intended to fit standard height Chevy Center bolt valve covers.

Product Features:

4 bolts included in each package
Allen head includes decorative O-ring cap
Triple chrome-plated finish
Fits standard height Chevy Center bolt valve covers

from

$214.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1987-1999 Chevrolet 305 and 1987-2000 Chevrolet 350 Center bolt engines, this valve cover features polished aluminum construction and a ball milled design. Sold in pairs, this stock profile cover includes baffles and bolts to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for 1987-1999 Chevrolet 305 and 1987-2000 Chevrolet 350 Center bolt engines
Baffled for breather system compatibility
Sold in pairs
Polished aluminum construction
Stock height
Features OEM style sealing edge
Includes bolts for installation

from

$89.99

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle. K&N air filters are backed by our famous 10-Year/Million Mile Limited Warranty, and they provide an environmentally friendly way to reduce landfill waste by avoiding disposable filters. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

from

$118.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$64.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
Not intended for use in emission controlled vehicles.

Upgrade your 1991 Chevrolet Corvette with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1991 Chevrolet Corvette, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Chevrolet or enhancing its overall performance, Performance and Racing Products are key to keeping your Corvette functioning at its best. At Advance Auto Parts, we offer a wide selection of 136 Performance and Racing Products for the 1991 Chevrolet Corvette, designed to meet your needs without breaking the bank. From Performance Fuel System replacements to Performance Oil Filters upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1991 Chevrolet Corvette at great prices. Our Performance and Racing Products inventory for this model ranges from just $9.99 to $1,028.99, with an average price of $153.64. Our 136 Performance and Racing Products in stock come from 21 trusted brands, so you’re sure to find the right part for your 1991 Chevrolet Corvette without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1991 Chevrolet Corvette, we stock popular OEM and aftermarket Performance and Racing Products from top names like K&N, Mr. Gasket, FEL-PRO Performance, and more. K&N Performance and Racing Products start at just $17.99 and boast an impressive 5 stars average rating from customers. Mr. Gasket and FEL-PRO Performance also bring quality to the table, with Performance and Racing Products available starting at $10.49, and at an average 4 stars rating. With 166 customer reviews and counting, our 1991 Chevrolet Corvette Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1991 Chevrolet Corvette is always ready to roll. We’re committed to providing you with everything you need to keep your Corvette in top shape, all in one place. Start shopping confidently below for your 1991 Chevrolet Corvette!

Best-Selling Performance Fuel Systems for 1991 Chevrolet Corvettes

Enhance the driving experience in your Chevrolet with 1 quality Performance Fuel System components, starting at $221.99.

show more show less

from

$221.99

Product Features:

OE IN-Tank Upgrade Pumps
Ideal For Supporting Performance Improvements
Replace Original Pump Exactly
Include All Necessary Hardware
Easy Installation

Most Popular 1991 Chevrolet Corvette Performance Oil Filters

Customize your Chevrolet with 3 Performance Oil Filters products like Performance Oil Filters and Performance Oil Filler Caps, all priced under $17.99.

show more show less

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

from

$10.49

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

Internally battled
High-porosity filter
Ideal for high performance
Includes rubber grommet

from

$12.99

This chrome-plated steel push-on breather/oil filler cap fits over your oil filler tube. It has a side fitting for easy PCV hose (positive crankcase ventilation) hook up. Perfect compliment to Mr. Gasket matching chrome oil filler tube, #2066

Product Features:

Chrome plated steel
Fits stock factory oil filler tubes
Features side PCV hook up tube
Includes Rubber Grommet

Top Picks for 1991 Chevrolet Corvette Performance Exhaust Products

Upgrade Chevrolet Corvettes with top-quality Performance Exhaust Products parts, including 10 OEM and aftermarket selections for your 1991 model.

show more show less

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$85.39

Product Features:

Water/Weather Resistant
Re-Useable
Will Not Burn Or Blow Out
Suitable For Port-Matching
Made In USA

from

$20.99

Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.

Product Features:

Manufactured from high-temperature acrylic blend exhaust material
Provides excellent sealing and durability
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Resists Deteriorating
Provides Excellent Torque Retention

from

$42.99

Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.

Product Features:

Withstands Intense Exhaust Heat
Reusable header, exhaust manifold and collector flange gaskets
Manufactured from “dead soft” aluminum layers – .125″ thick
Easy Removal For Disassembly
Conforms easily to surface irregularities (warped flanges)
Compresses down to 0.060″ to create a tight leak-proof seal
Will not shrink, deteriorate, or blow out- eliminating gasket leaks
For high performance street, drag race and oval track use

from

$42.99

Withstands Intense Exhaust Heat
Reusable header, exhaust manifold and collector flange gaskets
Resists Deteriorating
Manufactured from “dead soft” aluminum layers – .125″ thick
Easy Removal For Disassembly
Conforms easily to surface irregularities (warped flanges)
Compresses down to 0.060″ to create a tight leak-proof seal
Will not shrink, deteriorate, or blow out- eliminating gasket leaks
For high performance street, drag race and oval track use

from

$30.19

Manufactured from high-temperature composite exhaust material. Provides maximum torque retention to eliminate gasket failure. Can be trimmed if necessary for modified port applications. Precision die cut for an excellent fit. For OE replacement, high-performance street, drag race and oval track.

Product Features:

High-Temperature Exhaust Material
Withstands Extreme Exhaust Heat
Provides Excellent Sealing And Durability
Superior Tensile Strength
Resists Deteriorating
Provides Excellent Torque Retention

from

$326.99

DynoMax Performance Exhaust is a leading performance exhaust brand built on over 25 years of market leadership. Each and every DynoMax product is backed by engineers who know what you want and expect out of a performance exhaust product… and who exceed your expectations every time.

from

$60.29

Copperseal exhaust gaskets are unique gaskets made from .043 inch solid copper. They feature an embossed O-ring design for a leak proof seal. They won’t shrink, deteriorate or blowout. Header bolts stay tight. Ideal for motor homes and towing.

Product Features:

Will Not Shrink/Deteriorate
Creates A Tight Leak Proof Seal
Helps Lower Under hood Temps
Seals Irregular Surfaces
Seals Slightly Damaged Surface
Ideal For Tow Vehicles
Ideal For Motor Homes

from

$59.99

Will Not Shrink/Deteriorate
Creates A Tight Leak Proof Seal
Helps Lower Under hood Temps
Seals Irregular Surfaces
Seals Slightly Damaged Surface
Ideal For Tow Vehicles
Ideal For Motor Homes

from

$51.99

Header Installation Kit – Chevrolet V8 1955-1991 265-400 Oval Port. Includes gaskets and fasteners necessary for header installation. Made using premium Ultra-Seal exhaust and collector gaskets. Mr. Gasket header and collector bolts deliver necessary clamp-load to seal flange mating surfaces.

Product Features:

Oval Port Header Gaskets
Port Size 1.50″ x 1.82″
Collector Gasket 3.00″ Diam. 3-bolt Style
Includes Header & Collector Bolts

In-Demand Performance Engines for 1991 Chevrolet Corvettes

Select from 50 premium Performance Engines parts for your 1991 Chevrolet Corvette, with prices ranging from $14.99 to $1,028.99.

show more show less

from

$39.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$52.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$23.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$329.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 Deg Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used
Accepts Late-Model Choke; Waterneck; and HEI
Accepts A/C And Alternator
Accepts Exhaust Heated Chokes

from

$151.99

Complete Kit: Includes Retainers And Locks
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Includes Superior Quality Steel Retainers
Includes 7 deg. Heat-Treated Valve Stem Locks
Retainers and Locks Black Oxide Coated
Non-Rotator Style: Dyno Tested and Street Proven
Great Match to Edelbrock Camshaft Kit

from

$23.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$215.99

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$111.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$17.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$32.99

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

Chrome Plated
Grade 5
AN washers with no exposed shoulder for a professional appearance

from

$39.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$65.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$38.49

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair, these gaskets are .187 inch thick. They fit both 1987-2002 Gen I Chevrolet Small Blocks as well as 1992-1997 Gen II LT-Based Small Blocks.

Product Features:

Manufactured from high-density cork /rubber blend gasket material
A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
For OE replacement, high performance street, drag race and oval track
.187″ thick
Handles Ex Flange Pressure
Forms Leak Proof Seal
Black Latex Coating

from

$63.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
Not intended for use in emission controlled vehicles.

from

$14.99

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$20.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Steel core gasket construction
Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
Not intended for use in emission controlled vehicles.

from

$126.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
O.D.: 1.254″, I.D.: .880″
Single valve springs with damper
Approximately .490″ max lift at recommended installed height

from

$68.99

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.130 inch, Compressed thickness 0.055 inch

Product Features:

Five layer (graphite core/perforated steel outer layers) composite construction
Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
Provides excellent stability, compressibility and high temperature endurance
Coated with high temperature silicone to ensure sealing of engine fluids
Will not brinell (indent) aluminum cylinder heads
For high performance street, drag race and oval track use
Compatible w/High Octane Fuel
Compatible With Exotic Fuel

from

$40.19

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material.
Provides excellent sealing and durability.
Can be trimmed if necessary for modified port applications.
Complete with manifold end seals and distributor gasket.
For OE replacement, high performance street, drag race and oval track use.

from

$32.99

Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.

Product Features:

Manufactured from .020″ steel shim stock.
Thinner than composition head gaskets – increases engine compression.
Stress formed embossments seal extreme cylinder pressures.
For high performance street, drag race and oval track use.

from

$42.49

Manufactured from cellulose/nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile rubber composition gasket material
Provides excellent sealing and durability
Complete with molded rubber front/rear oil pan end seals where applicable
For OE replacement, high performance street, drag race and oval track use
Graphite Non-Wicking Rubber
No Cork Particles
Easy Removal For Disassembly

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$333.99

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$187.99

Product Features:

Case-Hardened Tubing
Surface Hardening
Welded Ends
0.3125 in. Diameter
Use with or without Hardened Steel Guideplates

from

$94.99

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$65.99

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Grade 8 Steel

from

$42.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use

from

$87.19

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

(16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
Shank O.D. .540″
Includes Locks and Hex Wrench
High-Quality Grade Steel
Heat-Treated For Ex Strength
Plated With Durable Gold Tone Finish

from

$1028.99

Product Features:

Designed for 1986-91 Tuned Port Injection 5.7L Small-Block Chevy Corvette engines originally equipped with center bolt valve covers
Flat Tappet Camshaft Type
60cc combustion chamber with 165cc intake port
Intake valve measures 2.02 and the exhaust measures 1.60
Sold as one complete head

from

$1028.99

Product Features:

Designed for 1987-95 Throttle Body Injection or Tuned Port Injection 5.7L Small-Block Chevy engines originally equipped with center bolt valve covers
Flat Tappet Camshaft Type
60cc chambers with 165cc intake ports
Size of intake valve is 2.02 in. and exhaust valve is 1.60 in.
Sold as one complete head

from

$1021.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Hand-Blended Intake and Exhaust Bowls
CNC-Matched Intake/Exhaust Ports in Std Location
Thicker Deck Surfaces than Other Brands
Hardened Tip Stainless Swirl-Polished Valves
Heli-Coils Rocker Studs And Exhaust Bolt Holes

from

$789.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$704.99

Product Features:

Great For Street Machines/Street Rods/Muscle Cars
Two Piece Design
Individual D-Shaped Runners
Optimized For Broad Power Range/Large Plenum Area
Can Be Used For Blow-Through Superchargers
Fully CNC Machined For A Perfect Fit
No Exhaust Crossover

from

$609.99

HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine
New Turbine Hub
New Springs/Rollers In Stator

from

$544.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, new turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$472.99

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$463.99

Utilizes late model alternator and A/C bracket mounting provisions. Has vacuum taps off Manifold runners. Uses cable bracket P/N 20-101 for GM 700R4 transmission. Extra installation hardware included.

Product Features:

High Rise Dual Plane Design
Holley Pro-Jection Tbi Mounting Flange
Erg Provisions

from

$371.99

Product Features:

High Rise/Dual Plane Design For Maximum Torque
Fully CNC Machined For A Perfect Fit
Square Bore Carburetor Flange
Exhaust Crossover For Improved Street Drivability
Permanent Mold Casting Process
Lighter/Smoother/Better Looking
More Consistent Castings

from

$259.99

Product Features:

2000-6500 RPM Power Band
Single Plane/Open Plenum Design
No Provision For Divorced Or Hot Air Choke
Square Flange Carburetor Mounting

from

$203.99

7.25 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$147.99

Complete Kit: Includes Retainers And Locks
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Includes Superior Quality Steel Retainers
Includes 7 deg. Heat-Treated Valve Stem Locks
Retainers and Locks Black Oxide Coated
Dyno Tested And Street Proven
Great Match to Edelbrock Camshaft Kit

from

$112.99

Use with a short water pump to convert to a long water pump.

Product Features:

Water Pump Spacer Kit

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$95.99

Valve Spring Retainers for Use OE Cast Iron Heads
Superior Quality Heat-Treated Steel
Machined for Strength with Black Oxide Finish
Finish Ensures Rust and Corrosion Protection

from

$75.99

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

Chrome plated
Grade 8
12-point head
AN washers with no exposed shoulder for a professional appearance

from

$68.99

High performance, race quality gasket with molded rubber coating over a steel core. Steel core provides rigidity and durability, preventing prevent push out while the molded rubber coating helps seal minor oil pan rail irregularities. The one piece design eliminates the need for separate end seals to make installation easier and even further reduce the possibility of oil leakage. Provides excellent sealing and durability. Excellent replacement for stock original equipment, high performance street, drag race and oval track. Includes gasket and new oil pan bolts.

Product Features:

Steel core provides rigidity, durability and prevents gasket push out
Molded rubber coating seals minor irregularities in pan surface
One piece design is easier to install and even less prone to leak
Direct replacement suitable for all uses – street, racing, heavy duty
Include both gasket and new oil pan bolts

from

$64.19

These are high quality nuts with allen set screws to provide you with that positive lock needed for Race or original equipment Rocker Arms.

Product Features:

They Are Zinc Dichromate Plated Steel
They Have Black Oxide Coated Set Screws
Keeps Rocker Arms Positively Locked
(16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
Includes Locks and Hex Wrench
Shank O.D. .603″

from

$42.49

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

Advance the cam for increased torque and horsepower
Tune your powerband for more end torque or increase top end horsepower
Includes (4) offset bushings and (1) 0 degree bushing
Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
Increase Top-End Horsepower

Most Sold 1991 Chevrolet Corvette Performance Air Filters

Explore our best-selling Chevrolet parts for the 1991 Corvette among 1 OEM and aftermarket options starting from $89.99.

show more show less

from

$89.99

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

Top-Rated Performance and Racing Products Brands For Your 1991 Chevrolet Corvette

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1991 Chevrolet Corvettes. Below you’ll find some of our best rated Performance and Racing Products from K&N, Mr. Gasket, and FEL-PRO Performance, and more. Performance and Racing Products from these brands that fit a 1991 Corvette start at just $10.49 and are rated as high as 5 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular K&N 1991 Chevrolet Corvette Performance and Racing Products

When it comes to maintaining or upgrading your 1991 Chevrolet Corvette, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. K&N ticks all of those boxes. We offer a wide selection of K&N Performance and Racing Products, specifically designed for the 1991 Chevrolet Corvette. With over 2 K&N brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $17.99, with an average price of just $53.99. Plus, with over 46 customer reviews and an average rating of 5 stars, you can trust that our K&N Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$89.99

(11)

Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration

“GREAT ADD ON !!!!!!!!”

from
$17.99

(35)

Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine

“Good”

Popular Mr. Gasket 1991 Chevrolet Corvette Performance and Racing Products

Mr. Gasket auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1991 Chevrolet Corvette owner should feel confident when installing genuine Mr. Gasket parts in their vehicle. To ensure the best fit and performance for your 1991 Corvette, Advance Auto Parts carries a full inventory of 31 Mr. Gasket Performance and Racing Products. Plus you will be keeping your Chevrolet in peak condition while saving money because prices on these Mr. Gasket Performance and Racing Products range from $10.49 to $94.99, plus, with more than 21 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

from
$17.49

This product is not rated

Oil Pan Bolt Kit

“”

from
$42.99

This product is not rated

Aluminum Exhaust Gasket: High-Heat Resistant, Easy Removal

“”

from
$48.09

This product is not rated

Thermocap Radiator Cap

“”

FAQs for 1991 Chevrolet Corvette Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1991 Chevrolet Corvettes?

Out of 136 Performance and Racing Products that fit 1991 Chevrolet Corvettes, the following parts are the top sellers:

Performance Exhaust Gasket Set for Enhanced Sealing and Durability (5020441) – $20.99
Dist:Chev V8 Hei Vac W/Coil (16370007) – $210.99
Aluminum Exhaust Gaskets for Intense Heat Resistance (6900015) – $42.99

What’s the price range for 1991 Chevrolet Corvette Performance and Racing Products?

Performance and Racing Product prices for the 1991 Chevrolet Corvette start at $9.99 and go up to $1,028.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1991 Chevrolet Corvette?

The average price for Performance and Racing Products for the 1991 Chevrolet Corvette is $153.64. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Chevrolet Corvette model years?

Yes, we currently carry Performance and Racing Products for 64 model years of Chevrolet Corvettes between 1953 and 2019. Performance and Racing Products are bought most frequently for the following model years: 2019, 2018, 2017, 2016, 2015, 2014, 2013, 2012, and 2011.

What are the cheapest Performance and Racing Products for my 1991 Chevrolet Corvette?

The cheapest 1991 Chevrolet Corvette Performance and Racing Products we carry in stock are:

Tie Rod Dust Boot (17360821) – $9.99
Enhancement Products (5022487) – $10.49
Ball Joint Dust Boot Set (22906822) – $10.99
D4260 Flame-Thrower Distributor Rotor HEI/EST Black (10111551) – $10.99
Chrome Oil Fill Cap – Push-On Style W/Tube For Pvc Hookup – Fitting For Easy Pcv Hose Hook Up (12030896) – $12.99

What are the top-rated Performance and Racing Products that fit the 1991 Chevrolet Corvette?

Out of 166 reviews by customers, our 1991 Chevrolet Corvette Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1991 Chevrolet Corvette and their top-rated products:

Performance Air Filters
- Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (17400060) – $89.99

What types of Performance and Racing Products do you sell for my 1991 Chevrolet Corvette?

As of 2/5/25, these are some of the most in-demand types of Performance and Racing Products for a 1991 Chevrolet Corvette:

Can I get help with 1991 Chevrolet Corvette Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Chevrolet Performance and Racing Products and more.

What is your return policy for Chevrolet Corvette Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Chevrolet Corvette Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1991 Chevrolet Corvette Performance and Racing Products

Holley – Keith Dorton Series; VoluMax Race Series Fuel Pump (Part No.12-327-20)

Lakewood – High Performance U-Joint (Part No.23016)

Edelbrock – C-66 Intake Manifold #5420 BB Chevy, Dual Quad, Square Bore, Oval Port, Natural (Part No.5420)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1047)

Edelbrock – Performer Small-Block Chevy Cylinder Head 64cc Hydraulic Flat Tappet (Part No.60909)

Edelbrock – Water Pump for Small-Block 1984-91 350 c.i.d. Corvettes in Satin Finish (Short) (Part No.8815)

B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)

Energy Suspension – Sway Bar Bushing Set (Part No.3.5193R)

Powertrax – No-Slip Traction System (Part No.9207853005)

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5894)

Energy Suspension – Leaf Spring Bushing Set (Part No.3.2123G)

Energy Suspension – Hyper-Flex System (Part No.3.18123G)

Edelbrock – Performer Carb/Plate Nitrous Systems for Spread-Bore (Q-Jet)Carbs (50-75-100 Hp) (Part No.70002)

Edelbrock – Pushrod Set for S/B Chevy (Part No.9646)

Mallory – Distributor Wiring Harness (Part No.29349)

Mr. Gasket – Thermocap Radiator Cap (Part No.2476BK)

MSD Ignition – Crank Trigger Kit; Small Block Chevy; 6? Balancer (Part No.8600)

Mr. Gasket – Rear Main Seal Gasket (Part No.1960)

Hypertech – Street Runner Power Computer Chip (Part No.120391)

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4377)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

MSD Ignition – Distributor; Corvette V8; Tach Drive with Vacuum Advance (Part No.8572)

Mr. Gasket – A/Tdipstick (Part No.9704G)

Spectre – Valve Cover (Part No.5280)

Spectre – SBC Aluminum Center Bolt Valve Cover (Part No.4995)

K&N – Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (Part No.33-2035)

Energy Suspension – Control Arm Bushing Set (Part No.3.3142R)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1884 R)

Edelbrock – High Performance In-Tank Fuel Pump – 255 liter/hr. (67 gph) (Part No.17933)

K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2002)

Mr. Gasket – Enhancement Products (Part No.2060)

Mr. Gasket – Chrome Oil Fill Cap – Push-On Style W/Tube For Pvc Hookup – Fitting For Easy Pcv Hose Hook Up (Part No.2063)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1444)

Flowtech – Real-Seal; Header Gasket (Part No.99150AFLT)

Mr. Gasket – Performance Exhaust Gasket Set for Enhanced Sealing and Durability (Part No.150B)

Mr. Gasket – Aluminum Exhaust Gaskets for Intense Heat Resistance (Part No.7402G)

Mr. Gasket – Aluminum Exhaust Gasket: High-Heat Resistant, Easy Removal (Part No.7401G)

Mr. Gasket – Exhaust Gasket Set (Part No.150)

Dynomax – Super Turbo Dual System (Part No.17483)

Mr. Gasket – Copper Seal; Exhaust Gasket Set (Part No.7151)

Mr. Gasket – Copper Seal; Exhaust Gasket Set (Part No.7150)

Mr. Gasket – Exhsthdrgskt (Part No.7652G)

FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1003)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1004)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Edelbrock – Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish (Part No.2104)

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

FEL-PRO Performance – PERFORMANCE VALVE COVER GASKET SET (Part No.1602)

Weiand – Action Plus Water Pumps (Part No.9208P)

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

Mr. Gasket – Bolt Water Pump (Part No.4998)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1010)

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5867)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1886)

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Competition Cams – Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height (Part No.981-16)

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5799G)

Mr. Gasket – Intake Gasket (Part No.116)

Mr. Gasket – Head Gasket (Part No.1130G)

Mr. Gasket – Ultra Seal: Oil Pan Gasket (Part No.5885)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2919)

Edelbrock – Water Pump for Small-Block 1984-91 350 c.i.d. Corvettes in Satin Finish (Short) (Part No.8815)

Edelbrock – Pushrod Set for S/B Chevy (Part No.9629)

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Mr. Gasket – Ultra Seal: Screw-In Rocker Arm Studs (Part No.1076)

Mr. Gasket – Intake Gasket (Part No.143)

Mr. Gasket – Ultra Seal: Sure-Lock Rocker Arm Nuts (Part No.923G)

Edelbrock – Performer Small-Block Chevy Cylinder Head Hydraulic Flat Tappet (Part No.60879)

Edelbrock – Performer Small-Block Chevy Cylinder Head Hydraulic Flat Tappet Cam (Part No.60859)

Edelbrock – XX Performer Small-Block Chevy Cylinder Head Flat Tappet Polished (Part No.608719)

B & M – Torque Converter, Holeshot 3000 (Part No.70421)

Weiand – Stealth Ram; Intake Manifold (Part No.7540)

B & M – Holeshot 2400 (Part No.70419)

B & M – Torque Converter, Holeshot 2000 (Part No.70417)

Edelbrock – Water Pump for Small-Block 1984-91 350 Corvettes in Polished Finish (Short) (Part No.8825)

Holley – Manifold; SBC Late DP TBI EGR (Part No.300-66)