1989 GMC C1500 Differentials

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1964-1970 Chevrolet 8.2 inch 10 bolt & 1970-1981 GM 8.5 inch ring gear

Product Features:

• .047″ thick cellulose/nitrile composite gasket material
• Precision die cut
• Reusable

9.5″ GM differential carrier Supershim kit.

Product Features:

• Super carrier shim kit for GM 9.5″
• Interlocking design makes installation much easier

Pennzoil? Synchromesh Fluid is designed to offer optimal protection for moderately loaded gears in manual transmissions. Containing a high detergent additive system, it helps cope with water, dust, dirt, and any other small deposits you might encounter on or off-road(1). Pennzoil? Synchromesh Fluid also offers synchronizer compatibility for performance in manual transmissions, specifically to fulfill the needs of Chrysler, GM, Honda and other transmission requirements. Pennzoil? Synchromesh Fluid meets General Motors specification 9985648 for use where GM part numbers 12345349 or 12345577 are called out for use. Chrysler manual transmission fluid specification MS-9224 is also met. This high quality manual transmission fluid is formulated for good low temperature flow to maintain shift characteristics even after a cold night(2). Corrosion protection is added to help protect your transmission. Pennzoil? Synchromesh fluid is a manual transmission fluid designed for certain manual trans axles and manual transmissions used by general motors or Chrysler. (1)The Anglamol 6091 additive system contains approximately twice the sulfonate detergent levels as current generation PCMO, 4500 ppm as magnesium of magnesium sulfonate. This engine oil type additive will emulsify water and polar contamination sufficiently to handle contamination levels above 0.5% water. Anglamol 6091 – Detergent, friction modifier, extreme pressure agent, seal swell, anti-wear, anti-oxidant. Chemical Composition – Magnesium sulphonate, alkenyl amide, alkenyl ester sulphide, alkenyl phosphite, alkylbenzene, hecterocyclic ether, zinc dithiophosphate. (2)Pour point is less than -39 Deg. C. Low temperature viscosity in a -40 Deg. C Brookfield test of 50,000 cPs maximum, less than a 75W gear oil and the cold cranking viscosity less than a typical conventional SAE 5W engine oil.

Product Features:

• Excellent yellow metal compatibility
• Meets GM specification 9985648 and Chrysler specification MS-9224
• Excellent synchronizer performance
• Exhibits excellent low-temperature performance

Differential Cover G

Product Features:

• FULL SPOOL GM 10 BOLT 8.5 28 SPL ST

Product Features:

• KIT SHIM PINION

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

• Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
• Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
• Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
• Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM89410 race
• All steel construction

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. This is a thick gear set for a 3.42 & down carrier.

Product Features:

• Fits GM 12 bolt truck
• 8.875″ ring gear diameter
• 30 spline pinion
• 12 ring gear bolts
• 4.56 ratio
• Thick gear for 3.42 and down carrier

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

• Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Crowned raceways and rollers to ensure even load distribution for maximum life
• Industry leading coverage
• Professional technicians know they can depend on National

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1998 and up GM 9.5″
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Product Features:

• Spider gear kit
• Fits GM 8.5″ 28 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Product Features:

• RING GEAR BOLT 8.5″ 7.5″ 7/16 X 20 LEFT HAND

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Product Features:

• Clutch kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
• 14 piece kit
• Composite clutches

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
• Includes carrier bearings and races and “super” carrier shim kit

Positraction clutch guide.

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
• Compatible with Dura Grip positractions only

Spectre Differential Covers are made to OEM specifications and are triple chrome plated for a lasting shine. Designed to protect the intricate moving parts of the differential, Spectre’s covers add an extra layer of protection to the vehicle’s underside. Featuring a 10-bolt design and including the necessary chrome bolts and gaskets, this differential cover is designed to fit 1964-1972 Chevy/GM intermediates, 1983-1987 Chevy/GMC 1/2 Ton two or four wheel drive rear, and 1967-1972 Chevy Camaros. Includes 10 SAE standard chrome bolts for installation. You’ll need to supply your own bolts if your application requires metric bolts.

Product Features:

• Made exactly to OEM specifications
• 10-bolt design, includes chrome bolts and gasket
• Triple chrome plated for a lasting shine
• 10 chrome 5/16 inch -18 x 3/4 inch differential cover bolts included

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

• Direct replacement – this differential end yoke matches the fit and construction of the original yoke
• Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
• Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
• Validated fit – this differential end yoke has been tested to confirm accurate fit

8.6″ GM standard Open side gear Thrust washer.

Product Features:

• Side gear thrust washer
• Fits GM 8.6″