1989 Chevrolet S10 Blazer Drivetrains

Popular 1989 Chevrolet S10 Blazer Drivetrains Categories

Essential Drivetrains for 1989 Chevrolet S10 Blazers

USA Standard Gear – Pinion Installation Kit For ’82-’99 GM 7.5" & 7.625" (Part No.60010)

Pinion Installation Kit For '82-'99 GM 7.5" & 7.625"

from

$153.99
7.5″ & 7.625″ GM 82-99 PINION KIT .

Product Features:
  • Fits 1982-1999 GM 7.5″ and 7.625″
  • Uses Koyo bearings and races
  • Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.
See More

Carquest Premium – 4WD Indicator Light Switch (Part No.FWA1001)

4WD Indicator Light Switch

from

$32.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

Yukon Gear – Pinion Install Kit For GM 7.5" Differential (Part No.13064)

Pinion Install Kit For GM 7.5" Differential

from

$203.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:
  • Fits 1982-1999 GM 7.5″ and 7.625″
  • Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.
See More

Motive Gear – Differential Pinion Shim Kit (Part No.1100)

Differential Pinion Shim Kit

from

$7.49
High-quality Differential Component Shim

Product Features:
  • SHIM KIT FITS-8.25-F7.5-AMC20-GM0
See More

Driveworks – Differential Seal (Part No.S-223255)

Differential Seal

from

$7.49
Product Features:
  • Brand may vary by location
See More

National – Shaft Repair Sleeve (Part No.99193)

Shaft Repair Sleeve

from

$43.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

Powertrax – Grip LS Traction System (Part No.LS201028)

Grip LS Traction System

from

$463.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!
See More

Dorman – Help – Transfer Case Switch (Part No.49315)

Transfer Case Switch

from

$29.99
This transfer case switch directly replaces the original equipment switch on certain vehicle years, makes and models.

Product Features:
  • Direct replacement – this 4WD switch matches the fit and function of the original switch on specific vehicle applications.
  • Effective fix – restores proper 4WD operation after original switch degrades and fails
  • Durable construction – built for reliable longevity, free of defects in materials and craftmanship
  • Trustworthy quality – backed by team of designers and engineers in the United States
See More

Pro-King – Differential Pinion Yoke Washer (Part No.742A215)

Differential Pinion Yoke Washer

from

$3.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:
  • All products are designed to meet or exceed OE quality, form, fit and funtion.
See More

National – Bearings (Part No.HM89210)

Bearings

from

$14.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Mahle – Differential Cover G (Part No.J7018826594MAH)

Differential Cover G

from

$13.85
Differential Cover G

Dorman – Spindle Nut 3/4 In.-20 Hex Size 1-1/16 In. (Part No.615-065.1)

Spindle Nut 3/4 In.-20 Hex Size 1-1/16 In.

from

$6.99
This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Dorman – 4WD Actuator Control Cable (Part No.600-601)

4WD Actuator Control Cable

from

$39.49
This 4WD actuator cable directly replaces the original equipment part on specific vehicle applications. It is reverse engineered to reliably restore proper functionality.

Product Features:
  • Direct replacement – this 4WD actuator cable matches the fit and function of the original cable on certain vehicle years, makes and models.
  • Effective fix – installation restores four-wheel drive function interrupted by a failed original cable.
  • Related repair – recommended for replacement when installing a new axle actuator
  • Trustworthy quality – backed by team of designers and engineers in the United States
See More

Dorman – Help – Axle Shaft Retainer (Part No.05311)

Axle Shaft Retainer

from

$6.49
An imperative replacement part for the proper functioning of the axle shaft and for basic vehicle operation, our Axle Shaft Lock C-Clips are made from quality materials for long-lasting durability.

Product Features:
  • Direct replacement – this drive axle shaft lock C-clip matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

National – Bearings (Part No.N-5210-KLB)

Bearings

from

$53.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Controlled heat treating process for lasting performance and extended bearing life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Driveworks – Oil Seal (Part No.S-8660S)

Oil Seal

from

$5.49
Value-priced seal meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

Dorman – Spindle Washer – I.D. 24.7mm O.D. 45.1mm Thickness 4.7mm (sold by each) (Part No.618-027)

Spindle Washer - I.D. 24.7mm O.D. 45.1mm Thickness 4.7mm (sold by each)

from

$2.29
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Driveworks – Taper Bearing Set (Part No.S-A-18)

Taper Bearing Set

from

$10.79
Value-priced bearing meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

Motive Gear – Differential Master Bearing Kit – Koyo (Part No.R7.5GRMK)

Differential Master Bearing Kit - Koyo

from

$124.99
Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:
  • GM 7.5 MASTER KIT BRG & SEAL ’82-98
See More

National – Shaft Repair Sleeve (Part No.99125)

Shaft Repair Sleeve

from

$24.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

National – Shaft Repair Sleeve (Part No.99128)

Shaft Repair Sleeve

from

$41.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

Richmond Gear – Differential Cross Shaft (Part No.CSPGM75)

Differential Cross Shaft

from

$26.49
Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:
  • For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
  • The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
  • Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
  • Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
  • Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.
See More

Driveworks – Ball Bearing (Part No.S-HB-88107-A)

Ball Bearing

from

$19.99
Value-priced bearing meets all cataloged application requirements.
See More

Dorman – Uni-Fit C.V. Joint Boot Kit Outer greater than 3.58 In. Diameter (Part No.614-003)

Uni-Fit C.V. Joint Boot Kit Outer greater than 3.58 In. Diameter

from

$32.99
This CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:
  • Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself.
  • Ideal solution – this kit is a reliable replacement for original components that have failed due to wear.
  • Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

USA Standard Gear – TCaseShiftForkInsert (Part No.70666)

TCaseShiftForkInsert

from

$11.99
TCaseShiftForkInsert

Motive Gear – Differential Spool (Part No.FS10-30)

Differential Spool

from

$187.99


Product Features:
  • FULL SPOOL GM 8.5 30 SPL ST MUST USE 2-LM102911 & 2-LM102949
See More

Richmond Gear – MiniSpool (Part No.78-7526-1)

MiniSpool

from

$124.99
MiniSpool

Motive Gear – Differential Mini Spool (Part No.MS7.5-28)

Differential Mini Spool

from

$101.99


Product Features:
  • MINI SPOOL GM 7 1/2″ 28 SPLINE
See More

Upgrade your 1989 Chevrolet S10 Blazer with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1989 Chevrolet S10 Blazer, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Chevrolet or enhancing its overall performance, Drivetrains are key to keeping your S10 Blazer functioning at its best. At Advance Auto Parts, we offer a wide selection of 236 Drivetrains for the 1989 Chevrolet S10 Blazer, designed to meet your needs without breaking the bank. From Transfer Case replacements to Drive Shafts and Axles upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1989 Chevrolet S10 Blazer at great prices. Our Drivetrains inventory for this model ranges from just $1.99 to $1,839.99, with an average price of $185.34. Our 236 Drivetrains in stock come from 20 trusted brands, so you’re sure to find the right part for your 1989 Chevrolet S10 Blazer without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1989 Chevrolet S10 Blazer, we stock popular OEM and aftermarket Drivetrains from top names like Valvoline, Moog, Driveworks, and more. Valvoline Drivetrains start at just $14.49 and boast an impressive 5 stars average rating from customers. Moog and Driveworks also bring quality to the table, with Drivetrains available starting at $5.49, and at an average 4 stars rating. With 1,744 customer reviews and counting, our 1989 Chevrolet S10 Blazer Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1989 Chevrolet S10 Blazer is always ready to roll. We’re committed to providing you with everything you need to keep your S10 Blazer in top shape, all in one place. Start shopping confidently below for your 1989 Chevrolet S10 Blazer!

Best-Selling Transfer Cases for 1989 Chevrolet S10 Blazers

Enhance the driving experience in your Chevrolet with 23 quality Transfer Case components, starting at $4.29.

Felpro – TRANSFER CASE GASKET SET (Part No.72769)

TRANSFER CASE GASKET SET

from

$19.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Engineered and manufactured specifically for the repair environment
  • Unsurpassed quality you can trust
  • Validated for fit, form, and function
See More

National – Bearings (Part No.M88010)

Bearings

from

$10.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

National – Multi Purpose Seal (Part No.5200)

Multi Purpose Seal

from

$12.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

National – Multi Purpose Seal (Part No.710046)

Multi Purpose Seal

from

$17.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

National – Multi Purpose Seal (Part No.9613S)

Multi Purpose Seal

from

$7.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

Dorman – Help – Transfer Case Switch (Part No.49315)

Transfer Case Switch

from

$29.99
This transfer case switch directly replaces the original equipment switch on certain vehicle years, makes and models.

Product Features:
  • Direct replacement – this 4WD switch matches the fit and function of the original switch on specific vehicle applications.
  • Effective fix – restores proper 4WD operation after original switch degrades and fails
  • Durable construction – built for reliable longevity, free of defects in materials and craftmanship
  • Trustworthy quality – backed by team of designers and engineers in the United States
See More

National – Multi Purpose Seal (Part No.7412S)

Multi Purpose Seal

from

$14.29
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

Driveworks – Oil Seal Kit (Part No.S-5200)

Oil Seal Kit

from

$6.79
Value-priced seal meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

Dorman – Oil Drain Plug Standard M22-1.50, Head Size 30mm (Part No.090-061CD)

Oil Drain Plug Standard M22-1.50, Head Size 30mm

from

$13.29
This transfer case oil drain plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this transfer case oil drain plug matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

National – Multi Purpose Seal (Part No.341022)

Multi Purpose Seal

from

$8.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

National – Shaft Repair Sleeve (Part No.99125)

Shaft Repair Sleeve

from

$24.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

National – Bearings (Part No.B-5020)

Bearings

from

$25.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Available in both caged design and full complement
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

USA Standard Gear – ManTransExtHouseBush (Part No.77793)

ManTransExtHouseBush

from

$8.99
ManTransExtHouseBush

USA Standard Gear – TCase Shift Fork (Part No.72275)

TCase Shift Fork

from

$36.99
TCase Shift Fork

National – Bearings (Part No.N-5210-KLB)

Bearings

from

$53.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Controlled heat treating process for lasting performance and extended bearing life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

National – Bearings (Part No.J-2416)

Bearings

from

$26.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Available in both caged design and full complement
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

USA Standard Gear – TRANSFER CASE PARTS (Part No.74317)

TRANSFER CASE PARTS

from

$176.99
TRANSFER CASE PARTS

USA Standard Gear – TCaseBrg-SealKit (Part No.73873)

TCaseBrg-SealKit

from

$132.99
TCaseBrg-SealKit

FAG US – CONE (Part No.KM86649)

CONE

from

$18.99
CONE

USA Standard Gear – TCaseShiftForkInsert (Part No.70666)

TCaseShiftForkInsert

from

$11.99
TCaseShiftForkInsert

USA Standard Gear – Shift Fork Insert (Part No.71380)

Shift Fork Insert

from

$11.99
Shift Fork Insert

FAG US – SHAFT SEAL (Part No.SS2569)

SHAFT SEAL

from

$5.19
SHAFT SEAL

USA Standard Gear – ManTransInptShftSeal (Part No.70537)

ManTransInptShftSeal

from

$4.29
ManTransInptShftSeal

Most Popular 1989 Chevrolet S10 Blazer Drive Shafts and Axles

Customize your Chevrolet with 32 Drive Shafts and Axles products like Drive Shaft and Axles, Axle Shaft Seals, and Axle Shaft Universal Joints, all priced under $675.99.

Driveworks – Oil Seal (Part No.S-8660S)

Oil Seal

from

$5.49
Value-priced seal meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

Spicer – Universal Joint (Part No.5-1310X)

Universal Joint

from

$35.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)

Center Support Bearing Motor Mount: Center, 1 Piece

from

$34.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:
  • MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
  • HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
  • READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
  • For Years: 1955-2018
  • Weight approx: 4 Lbs
  • BEARING ID / BORE: 1.5750 INCH / 40 MM
  • CENTERLINE: 2.48 INCH / 63 MM
  • MOUNT WIDTH: 6.62 INCH / 168 MM
  • STYLE: ROUND FRAME
  • NOT PICTURED: TWO DUST SHIELDS
See More

Dorman – Help – Axle Shaft Retainer (Part No.05311)

Axle Shaft Retainer

from

$6.49
An imperative replacement part for the proper functioning of the axle shaft and for basic vehicle operation, our Axle Shaft Lock C-Clips are made from quality materials for long-lasting durability.

Product Features:
  • Direct replacement – this drive axle shaft lock C-clip matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

National – Shaft Repair Sleeve (Part No.99174)

Shaft Repair Sleeve

from

$45.49
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

National – Bearings (Part No.A-5)

Bearings

from

$16.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Carquest Premium – CV Axle Shaft Assembly (Part No.NCV10035)

CV Axle Shaft Assembly

from

$139.99
All CARQUEST axles have a new zinc dichromate plated nut or attaching hardware. CV joint grease has a high moly content. The boot bands are made from stainless steel, and the boots are manufactured to resist wear and damage due to extreme high and low temperatures.High moly CV joint grease with stainless-steel boot bands
See More

Driveworks – Axle Repair Bearing (Part No.S-RP-5707)

Axle Repair Bearing

from

$16.49
Value-priced bearing meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

National – Multi Purpose Bearing (Part No.HB-88107-A)

Multi Purpose Bearing

from

$44.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Controlled heat treating process for lasting performance and extended bearing life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)

Center Support Bearing Motor Mount: Center, 1 Piece

from

$22.79
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:
  • MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
  • HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
  • READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
  • For Years: 1955-2018
  • Weight approx: 3 Lbs
  • BEARING ID / BORE: 1.3780 INCH / 35 MM
  • CENTERLINE: 2.28 INCH / 58 MM
  • MOUNT WIDTH: 6.62 INCH / 168 MM
  • STYLE: ROUND FRAME
  • COMPLETE MOUNT
See More

Driveworks – Ball Bearing (Part No.S-HB-88107-A)

Ball Bearing

from

$19.99
Value-priced bearing meets all cataloged application requirements.
See More

National – Bearings (Part No.B-2010)

Bearings

from

$15.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Available in both caged design and full complement
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6035)

Center Support Bearing Motor Mount: Center, 1 Piece

from

$13.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 58-02; GMC 55-02; INTL 57-02;. Please verify your application.

Product Features:
  • MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
  • HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
  • READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
  • For Years: 1955-2002
  • Weight approx: 2 Lbs
  • BEARING ID / BORE: 1.1811 INCH / 30 MM
  • CENTERLINE: 3.50 INCH / 89 MM
  • MOUNT WIDTH: 1.50 INCH / 38 MM
  • COMPLETE MOUNT
See More

National – Multi Purpose Seal (Part No.4529N)

Multi Purpose Seal

from

$10.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

Dorman – Drive Shaft Repair Kit – Only Fits Dorman Driveshafts (Part No.932-988)

Drive Shaft Repair Kit - Only Fits Dorman Driveshafts

from

$51.99
This drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:
  • Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle.
  • Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue.
  • Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Driveworks – Drive Shaft Center Support (Part No.S-HB-88107-E)

Drive Shaft Center Support

from

$42.99
Product Features:
  • Brand may vary by location
See More

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6027)

Center Support Bearing Motor Mount: Center, 1 Piece

from

$5.29
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 87-97; GMC 67-05; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:
  • MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
  • HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
  • READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
  • For Years: 1955-2012
  • Weight approx: 1 Lbs
  • CUSHION INSERT ONLY
  • FOR COMPLETE MOUNT SEE PART 6056
See More

National – Bearings (Part No.88107-BVV)

Bearings

from

$32.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Controlled heat treating process for lasting performance and extended bearing life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Driveworks – Clutch Release Bearing (Part No.S-B-2010)

Clutch Release Bearing

from

$8.49
Product Features:
  • Brand may vary by location
See More

Yukon Gear – Replacement Inner Axle Seal For Dana 44 (Flanged Axle) (Part No.30303)

Replacement Inner Axle Seal For Dana 44 (Flanged Axle)

from

$7.99
Replacement inner axle seal for Dana 44 (flanged axle) .Yukon Mighty seal.

Product Features:
  • Inner axle seal
  • Fits Dana Spicer 44 rear with flanged axle
See More

USA Standard Gear – Driveshaft – Front (Part No.44326)

Driveshaft - Front

from

$675.99
Driveshaft – Front

Dorman – Rear Drive Shaft: Greaseable (Part No.976-806)

Rear Drive Shaft: Greaseable

from

$563.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:
  • Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
  • 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
  • Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
  • Serviceable construction – non-staked universal joints are designed for future serviceability
See More

Dorman – Rear Drive Shaft: Greaseable (Part No.976-808)

Rear Drive Shaft: Greaseable

from

$532.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:
  • Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
  • 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
  • Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
  • Serviceable construction – non-staked universal joints are designed for future serviceability
See More

Dorman – Front Drive Shaft: Greaseable, Adjustable, OE Fix (Part No.938-219)

Front Drive Shaft: Greaseable, Adjustable, OE Fix

from

$366.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:
  • Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation.
  • Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance.
  • All-new manufacturing – made 100% new, not remanufactured, so there’s no core charge or return hassle
  • Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience
See More

FAG US – AXLE SHAFT REPAIR BE (Part No.DR0148K)

AXLE SHAFT REPAIR BE

from

$64.99
AXLE SHAFT REPAIR BE

Spicer – SPICER U-JOINT (Part No.5-1310-1X)

SPICER U-JOINT

from

$44.99
SPICER U-JOINT

FAG US – AXLE BEARING (Part No.FC67147)

AXLE BEARING

from

$36.49
AXLE BEARING

National – Bearings (Part No.SCH-1810)

Bearings

from

$18.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Available in both caged design and full complement
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

FAG US – BEARING (Part No.B2010)

BEARING

from

$11.99
BEARING

Dorman – Spindle Nut (Part No.K1002831647DOR)

Spindle Nut

from

$6.19
Spindle Nut

FAG US – SHAFT SEAL (Part No.SS2468)

SHAFT SEAL

from

$5.19
SHAFT SEAL

Pro-King – Axle Seal (Part No.721A074)

Axle Seal

from

$1.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:
  • All products are designed to meet or exceed OE quality, form, fit and funtion.
See More

Top Picks for 1989 Chevrolet S10 Blazer 4WD Components

Upgrade Chevrolet S10 Blazers with top-quality 4WD Components parts, including 6 OEM and aftermarket selections for your 1989 model.

Dorman – 4WD Actuator Control Cable (Part No.600-601)

4WD Actuator Control Cable

from

$39.49
This 4WD actuator cable directly replaces the original equipment part on specific vehicle applications. It is reverse engineered to reliably restore proper functionality.

Product Features:
  • Direct replacement – this 4WD actuator cable matches the fit and function of the original cable on certain vehicle years, makes and models.
  • Effective fix – installation restores four-wheel drive function interrupted by a failed original cable.
  • Related repair – recommended for replacement when installing a new axle actuator
  • Trustworthy quality – backed by team of designers and engineers in the United States
See More

Carquest Premium – 4WD Indicator Light Switch Connector (Part No.PTA1174)

4WD Indicator Light Switch Connector

from

$35.49
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:
  • Premium quality materials for longer service life
  • Sealed connections (where applicable) to prevent environmental corrosion and performance issues
  • Global coverage for import and/or domestic applications
  • OE specified wire gauge to ensure a reliable electrical connection
  • Designed to meet or exceed OE specifications in form, fit and function
See More

Dorman – 4WD Front Differential Actuator (Part No.600-102XD)

4WD Front Differential Actuator

from

$131.99
This 4WD actuator directly replaces the original equipment part on specific vehicle applications. It is reverse engineered to reliably restore proper functionality.

Product Features:
  • Improved design – this 4WD actuator has been redesigned to eliminate common failures in the original part caused by exposure to ozone.
  • Upgraded materials – the rubber diaphragm in this 4WD actuator is reinforced with a mesh layer to provide 3X greater durability than the original material.
  • Seamless repair – this upgraded 4WD actuator matches the fit and function of the original part for a trouble-free installation
  • Quality assured – backed by a team of product experts in the United States and more than a century of automotive experience
See More

Carquest Premium – 4WD Actuator (Part No.FWC1091)

4WD Actuator

from

$80.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

Carquest Premium – 4WD Indicator Light Switch (Part No.FWA1001)

4WD Indicator Light Switch

from

$32.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

Carquest Premium – 4WD Indicator Light Switch (Part No.FWA1023)

4WD Indicator Light Switch

from

$18.79
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

In-Demand Universal Joints for 1989 Chevrolet S10 Blazers

Select from 24 premium Universal Joints parts for your 1989 Chevrolet S10 Blazer, with prices ranging from $2.59 to $50.99.

Spicer – Universal Joint (Part No.5-153X)

Universal Joint

from

$28.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.
See More

Driveworks – Universal Joint (Part No.DW-445)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging, having higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals to optimize grease retention and reduce contamination
See More

Neapco – Universal Joint (Part No.1-0025)

Universal Joint

from

$2.59
Universal Joint Strap Kit
See More

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.534G)

Greaseable Premium Universal Joint

from

$26.99
Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
  • KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
  • Cross forging shape and flash provide easier installation and high strength
See More

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.369)

Greaseable Premium Universal Joint

from

$19.99
Backed by superior materials and rigorous testing, MOOG Heavy Duty universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for fleets, off-highway and commercial vehicles
  • STRONG AND DURABLE — Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • GREASEABLE DESIGN — Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
  • INHIBITS PREMATURE WEAR — Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
  • RELIABLE PERFORMANCE — Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
See More

Driveworks – Universal Joint (Part No.DW-534G)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging to provide higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting allows for easy maintenance and the flexible use of the entire assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals are applied to optimize grease retention and reduce contamination
See More

MOOG Driveline Products – Universal Joint Strap Kit (Part No.530-10)

Universal Joint Strap Kit

from

$11.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:
  • For U-Joints 355, 372 & 534G
  • Contains two 1.81″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws
See More

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.234)

Non-Greaseable Super Strength Universal Joint

from

$32.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.269)

Non-Greaseable Super Strength Universal Joint

from

$32.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.280)

Greaseable Super Strength Universal Joint

from

$32.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

Spicer – Universal Joint (Part No.5-795X)

Universal Joint

from

$50.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More

Neapco – Universal Joint (Part No.2-3010)

Universal Joint

from

$8.99
Universal Joint
See More

Driveworks – Universal Joint (Part No.DW-369)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging, having higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals to optimize grease retention and reduce contamination
See More

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.235)

Greaseable Super Strength Universal Joint

from

$34.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

Spicer – Universal Joint (Part No.5-3147X)

Universal Joint

from

$32.49
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.
See More

Neapco – Universal Joint (Part No.1-0154)

Universal Joint

from

$6.49
Universal Joint
See More

Driveworks – Universal Joint (Part No.DW-235)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging, having higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals to optimize grease retention and reduce contamination
See More

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.445)

Greaseable Premium Universal Joint

from

$24.99
Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
  • KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
  • Cross forging shape and flash provide easier installation and high strength
See More

Neapco – Universal Joint (Part No.2-3011)

Universal Joint

from

$4.59
Universal Joint
See More

Neapco – Universal Joint (Part No.1-0153)

Universal Joint

from

$4.49
Universal Joint
See More

Dorman – Help – U-Joint Repair Kit (Part No.81001)

U-Joint Repair Kit

from

$11.49
This universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:
  • Direct replacement – this universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles.
  • Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
  • Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

MOOG Driveline Products – Universal Joint Strap Kit (Part No.360-10)

Universal Joint Strap Kit

from

$11.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:
  • For U-Joints 354, 368, 369, 445 & 455
  • Contains two 1.59″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws
See More

Dorman – Help – U-Joint Repair Kit (Part No.81000)

U-Joint Repair Kit

from

$6.99
This universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:
  • Direct replacement – this universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles.
  • Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
  • Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.225)

Greaseable Super Strength Universal Joint

from

$32.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:
  • BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
  • COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
  • CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
  • GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
  • KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
  • RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
  • STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
See More

Most Sold 1989 Chevrolet S10 Blazer Differentials

Explore our best-selling Chevrolet parts for the 1989 S10 Blazer among 142 OEM and aftermarket options starting from $1.99.

Valvoline – DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (Part No.822405)

DEXRON - VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart

from

$14.49
Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:
  • Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
  • Enhanced anti-shudder protection for smooth shifting and maximum power transfer
  • Developed with anti-wear technology to help improve transmission durability
  • Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
See More

Valvoline – DEX/MERC Automatic Transmission Fluid, 1 Gallon (Part No.773636)

DEX/MERC Automatic Transmission Fluid, 1 Gallon

from

$35.99
Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON®, DEXRON®-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:
  • Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
  • Enhanced anti-shudder protection for smooth shifting and maximum power transfer
  • Developed with anti-wear technology to help improve transmission durability
  • Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
See More

Felpro – DIFFERENTIAL GASKET (Part No.RDS 55072)

DIFFERENTIAL GASKET

from

$7.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Unsurpassed quality you can trust
  • Validated for fit, form and function
  • Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
See More

Motive Gear – Differential Pinion Shim Kit (Part No.1100)

Differential Pinion Shim Kit

from

$7.49
High-quality Differential Component Shim

Product Features:
  • SHIM KIT FITS-8.25-F7.5-AMC20-GM0
See More

Motive Gear – Differential Carrier Gear Kit (Part No.GM7.6BI)

Differential Carrier Gear Kit

from

$159.99


Product Features:
  • INTERNAL KIT-GM 7.6″ W/28 SPLINE
See More

National – Wheel Bearing and Seal Kit (Part No.RA-320)

Wheel Bearing and Seal Kit

from

$151.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Spindle bearing and seal kit
  • Includes all components required to complete the repair
  • Controlled heat treating process for lasting performance and extended bearing life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

National – Shaft Repair Sleeve (Part No.99193)

Shaft Repair Sleeve

from

$43.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

Motive Gear – Differential Carrier Gear Kit (Part No.GM10BI-30)

Differential Carrier Gear Kit

from

$153.99


Product Features:
  • GM10 BOLT 8.5″ 30 SPL INTERNAL KIT 1988-1999 (OPEN)
See More

Motive Gear – Differential Master Bearing Kit – Koyo (Part No.R7.5GRMK)

Differential Master Bearing Kit - Koyo

from

$124.99
Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:
  • GM 7.5 MASTER KIT BRG & SEAL ’82-98
See More

Motive Gear – Differential Ring and Pinion (Part No.GM10-342A)

Differential Ring and Pinion

from

$235.99


Product Features:
  • GM 10BL 8.5 R/P 3.42A MG FRT/REAR
See More

Driveworks – Taper Bearing Set (Part No.S-A-18)

Taper Bearing Set

from

$10.79
Value-priced bearing meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

Dorman – Rear Differential Cover (Part No.697-701)

Rear Differential Cover

from

$20.99
This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:
  • Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles.
  • Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid.
  • Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
  • Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
See More

Idemitsu – Type TLS Automatic Transmission Fluid – 1 qt (Part No.10106-042K)

Type TLS Automatic Transmission Fluid - 1 qt

from

$11.79
Formulated to meet the specific requirements of Toyota, Lexus, and scion vehicles equipped with conventional (non-CVT) transmissions that require the use of ATF T-IV. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF T-IV is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:
  • Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
  • Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
  • Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
  • Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
  • Advanced anti-wear technology provides maximum protection to gears and bearings
  • Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
See More

Motive Gear – Differential Ring and Pinion (Part No.GM10-373A)

Differential Ring and Pinion

from

$241.99


Product Features:
  • GM 10BL 8.5 R/P 3.73A MG FRT/REAR
See More

Dorman – Help – Differential Shaft Lock Bolt (Part No.81048)

Differential Shaft Lock Bolt

from

$5.99
This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Motive Gear – Differential Ring and Pinion (Part No.GM10-373)

Differential Ring and Pinion

from

$243.99


Product Features:
  • GM 10BL 8.5 R/P 3.73 MG FRT/REAR
See More

Motive Gear – Differential Carrier Shim Kit (Part No.1101)

Differential Carrier Shim Kit

from

$8.49
High-quality Differential Carrier Shim Kit

Product Features:
  • CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON
See More

Dorman – Rear Axle Shaft, Left or Right (Part No.630-103)

Rear Axle Shaft, Left or Right

from

$195.99
Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:
  • Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models.
  • Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications.
  • Durable construction – designed to rigorous standards and tested to ensure performance
  • Trustworthy solution – backed by team of engineers and quality control specialists in the United States
See More

Motive Gear – Differential Bearing Kit – Timken (Part No.R7.5GRT)

Differential Bearing Kit - Timken

from

$99.99
Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:
  • KIT BRG & SEAL GM 7.5″,’82-98
See More

Motive Gear – Pinion Nut (Part No.1260823)

Pinion Nut

from

$8.49
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.
See More

Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)

3 Qt - 80W90 Conventional Gear Oil With Posi Additive

from

$57.99
3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:
  • Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive
See More

Motive Gear – Ring Gear Bolt (Part No.14066913)

Ring Gear Bolt

from

$2.49


Product Features:
  • RING GEAR BOLT 8.5″ 7.5″ 7/16 X 20 LEFT HAND
See More

National – Bearings (Part No.M86610)

Bearings

from

$9.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Dorman – Help – Pinion Crush Sleeves (Part No.81058)

Pinion Crush Sleeves

from

$6.49
This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:
  • Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles.
  • Required replacement – when servicing the differential
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Motive Gear – Pinion Seal (Part No.8610)

Pinion Seal

from

$3.99
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.
See More

MOOG – Differential Carrier Bushing (Part No.K6572)

Differential Carrier Bushing

from

$15.29
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:
  • Manufactured from high quality elastomer compounds for durability and ride performance
  • Assembled with proper precompression for ultimate in performance and feel
  • High level bonding adhesive is used for durability
  • Elastomer compounds do not utilize any reground rubber fillers
See More

ATP – DIFF COVER KIT (Part No.111102)

DIFF COVER KIT

from

$29.99
DIFF COVER KIT

Driveworks – Taper Bearing Cup (Part No.S-LM-501314)

Taper Bearing Cup

from

$7.29
Value-priced bearing meets all cataloged application requirements.

Product Features:
  • Brand may vary by location
See More

Motive Gear – Crush Sleeve (Part No.1234726)

Crush Sleeve

from

$4.29
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.
See More

Motive Gear – Differential Carrier (Part No.GM8.6L)

Differential Carrier

from

$221.99
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o
See More

National – Bearings (Part No.HM89249)

Bearings

from

$28.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Motive Gear – Differential Pinion Shim Kit (Part No.1104)

Differential Pinion Shim Kit

from

$12.99


Product Features:
  • KIT SHIM
See More

Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)

Redline Synthetic "Shock Proof" Oil With Positraction Additive - 4 Quarts

from

$148.99
Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:
  • Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive
See More

National – Shaft Repair Sleeve (Part No.99155)

Shaft Repair Sleeve

from

$38.49
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

National – Shaft Repair Sleeve (Part No.99225)

Shaft Repair Sleeve

from

$28.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Designed to repair damaged, grooved or worn shafts
  • Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
  • Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
  • Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
  • Easy to install with removable flange and installation tool
  • Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
See More

Driveworks – Differential Seal (Part No.S-223255)

Differential Seal

from

$7.49
Product Features:
  • Brand may vary by location
See More

Motive Gear – OEC GM 7.6" 28 SPL 3.23-UP (Part No.GM7.6E)

OEC GM 7.6" 28 SPL 3.23-UP

from

$138.99
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.
See More

Motive Gear – Differential Master Bearing Kit – Timken (Part No.R7.5GRMKT)

Differential Master Bearing Kit - Timken

from

$129.99
Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:
  • GM 7.5 TIMKEN MASTER KIT ’82-98
See More

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)

Redline Synthetic "Shock Proof" Oil - 3 Quarts

from

$99.99
Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:
  • Includes three quarts of Redline Shockproof oil
See More

Motive Gear – Performance Differential Ring and Pinion (Part No.G885488)

Performance Differential Ring and Pinion

from

$232.99


Product Features:
  • GM 10BL 8.5 R/P 4.88 FRT/REAR MGP
See More

Motive Gear – Differential Ring and Pinion (Part No.GM7.5-373)

Differential Ring and Pinion

from

$224.99


Product Features:
  • GM 10BL 7.5&7.625 R/P 3.73 MG 10 3/8 X 18 LH THRED BLTS, PD=1.438
See More

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)

Redline Synthetic "Shock Proof" Oil - 4 Quarts

from

$137.99
Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:
  • Includes four quarts of Redline Shockproof oil
See More

National – Bearings (Part No.HM89210)

Bearings

from

$14.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

National – Multi Purpose Seal (Part No.223255)

Multi Purpose Seal

from

$12.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

Motive Gear – Differential Ring and Pinion (Part No.GM10-390)

Differential Ring and Pinion

from

$233.99


Product Features:
  • GM 10BL 8.5 R/P 3.90 MG FRT/REAR
See More

Dorman – Rear Axle Shaft, Left or Right (Part No.630-124)

Rear Axle Shaft, Left or Right

from

$245.99
Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:
  • Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models.
  • Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications.
  • Durable construction – designed to rigorous standards and tested to ensure performance
  • Trustworthy solution – backed by team of engineers and quality control specialists in the United States
See More

Motive Gear – Differential Ring and Pinion (Part No.GM10-430)

Differential Ring and Pinion

from

$258.99


Product Features:
  • GM 10BL 8.5 R/P 4.30
See More

Motive Gear – Differential Ring and Pinion (Part No.GM7.5-342)

Differential Ring and Pinion

from

$224.99


Product Features:
  • GM 10BL 7.5&7.625 R/P 3.42 MG 10 3/8 X 18 LH THRED BLTS, PD=1.438
See More

Top-Rated Drivetrains Brands For Your 1989 Chevrolet S10 Blazer

Shop for the best-rated brands offering Drivetrains and other products for your 1989 Chevrolet S10 Blazers. Below you’ll find some of our best rated Drivetrains from Valvoline, Moog, and Driveworks, and more. Drivetrains from these brands that fit a 1989 S10 Blazer start at just $5.49 and are rated as high as 5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Valvoline 1989 Chevrolet S10 Blazer Drivetrains

When it comes to maintaining or upgrading your 1989 Chevrolet S10 Blazer, using quality Drivetrains is essential to ensure durability and a perfect fit. Valvoline ticks all of those boxes. We offer a wide selection of Valvoline Drivetrains, specifically designed for the 1989 Chevrolet S10 Blazer. With over 2 Valvoline brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $14.49, with an average price of just $25.24. Plus, with over 19 customer reviews and an average rating of 5 stars, you can trust that our Valvoline Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

DEXRON - VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart
from
$14.49

(2)

DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart

“I’ve used this in my 2005 2500HD since I bought the truck with 20k on it now at 280k changed every other year maybe 40k I’d put on in two years,
I pu”

DEX/MERC Automatic Transmission Fluid, 1 Gallon
from
$35.99

(17)

DEX/MERC Automatic Transmission Fluid, 1 Gallon

“Equivalent to oem”

Popular Moog 1989 Chevrolet S10 Blazer Drivetrains

Moog auto parts is one of the highest quality Drivetrain brands in the market. Any 1989 Chevrolet S10 Blazer owner should feel confident when installing genuine Moog parts in their vehicle. To ensure the best fit and performance for your 1989 S10 Blazer, Advance Auto Parts carries a full inventory of 11 Moog Drivetrains. Plus you will be keeping your Chevrolet in peak condition while saving money because prices on these Moog Drivetrains range from $11.99 to $34.99, plus, with more than 343 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

Differential Carrier Bushing
from
$15.29
This product is not rated

Differential Carrier Bushing

“”

Greaseable Super Strength Universal Joint
from
$32.99
This product is not rated

Greaseable Super Strength Universal Joint

“”

Universal Joint Strap Kit
from
$11.99
This product is not rated

Universal Joint Strap Kit

“”

FAQs for 1989 Chevrolet S10 Blazer Drivetrains

Which Drivetrains are best-sellers for 1989 Chevrolet S10 Blazers?

Out of 236 Drivetrains that fit 1989 Chevrolet S10 Blazers, the following parts are the top sellers:

What’s the price range for 1989 Chevrolet S10 Blazer Drivetrains?

Drivetrain prices for the 1989 Chevrolet S10 Blazer start at $1.99 and go up to $1,839.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1989 Chevrolet S10 Blazer?

The average price for Drivetrains for the 1989 Chevrolet S10 Blazer is $185.34. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Chevrolet S10 Blazer model years?

Yes, we currently carry Drivetrains for 11 model years of Chevrolet S10 Blazers between 1983 and 1994. Drivetrains are bought most frequently for the following model years: 1994, 1993, 1992, 1991, 1990, 1988, 1987, 1986, and 1985.

What are the cheapest Drivetrains for my 1989 Chevrolet S10 Blazer?

The cheapest 1989 Chevrolet S10 Blazer Drivetrains we carry in stock are:

What are the top-rated Drivetrains that fit the 1989 Chevrolet S10 Blazer?

Out of 1,744 reviews by customers, our 1989 Chevrolet S10 Blazer Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1989 Chevrolet S10 Blazer and their top-rated products:

Can I get help with 1989 Chevrolet S10 Blazer Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Chevrolet Drivetrains and more.

What is your return policy for Chevrolet S10 Blazer Drivetrains?

Advance Auto Parts keeps returns simple. For new Chevrolet S10 Blazer Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.