1988 Porsche 944 Cooling and Climate Controls
More 1988 Porsche 944 Cooling and Climate Controls Categories
If you’re looking for an original Cooling and Climate Controls replacement for a 1988 Porsche 944, you can search through our selection below. You’ll also find aftermarket and OEM Cooling and Climate Controls to meet your needs.
Essential 1988 Porsche 944 Cooling and Climate Controls
Behr – A/C Pressure Switch (Part No.R1054178181BEH)
from
$22.52
Behr GmbH & Co. KG, Stuttgart, is a specialist for automotive air conditioning and engine cooling systems, the Behr Group is one of the world’s leading manufacturers and suppliers of Original Equipment cooling and air conditioning products for European passenger and commercial vehicles. 2 bar low pressure and 30 bar high pressure binary switch. This switch is designed to be compatible with R-12 and R134a refrigerants. Located on receiver-drier with 2 spade terminals. Used for compressor cut-out.
See More
Elring – SEAL RING – COPPER (Part No.4M20011240ELR)
from
$1.24
SEAL RING – COPPER
Carquest Premium – Multi Purpose Relay (Part No.RAA1234)
from
$19.99
Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More
Carquest Premium – HVAC Blower Motor Resistor (Part No.RUA1947)
from
$512.99
HVAC Blower Motor Resistor
Delphi – Engine Coolant Temperature Sensor (Part No.TS10250)
from
$30.49
Delphi temperature sensors are built with the latest OE technology; Delphi temperature sensors use durable, one-piece design; Delphi temperature sensors are impervious to electrical noise and interference.
Product Features:
See More
Product Features:
- Delphi temperature sensors deliver accurate readings and optimal performance
- Delphi’s one-piece design and automated production process eliminates internal connectors and failure points
- Each sensor is electrically insulated to eliminate interference from other components in the vehicle
- Delphi temperature sensors are impervious to electrical noise and interference
Permatex – The Right Stuff Grey Instant Gasket Maker, 147ml Cartridge (Part No.34311)
from
$28.49
Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.
Product Features:
See More
Product Features:
- Ideal for rigid cast aluminum parts
- Meets OEM Specifications
- Sensor safe & non-corrosive
- Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
- Blowout resistant, allowing leakproof gaskets to be made in just one minute
- Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
- Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
- Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
- Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.
Original Equipment – Water Pump O-Ring (Part No.G305930457OEA)
from
$3.90
Water Pump O-Ring
Original Equipment – Block Off Plate (Part No.G307423473OEA)
from
$13.36
Block Off Plate
Dorman – 5-Wire Style Relay (Part No.85170)
from
$15.99
This HVAC relay connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this HVAC relay connector matches the appearance and function of the factory hardware on specified applications
- Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Original Equipment – Original Equipment Thermostat Circlip (Part No.G400882673OEA)
from
$4.17
The Original Equipment Thermostat Circlip is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.
Product Features:
See More
Product Features:
- Premium Original Equipment replacement
- Provides performance and dependability
- Manufactured to meet OE specifications
Permatex – The Right Stuff: 1 Minute Gasket Maker: Grey, 3 OZ (Part No.25238)
from
$19.99
Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.
Product Features:
See More
Product Features:
- Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
- Sensor-safe, non-corrosive, RTV silicone
- Protects against leaks caused by vibration and thermal expansion
- Meets performance specs of OE silicone gaskets
- Quickly returns vehicle to service in just 1 minute
Geba – Water Pump (Part No.G300023931GEB)
from
$418.60
The GEBA Water Pump contains no remanufactured components and is manufactured to ensure high efficiency and optimal cooling under all conditions. Geba maintenance free Bearings with ball and roller spindle bearings are designed for the highest axial and radial stresses. Up to Date unitized sealing technology ensure optimal leak tightness and longevity. All housings are examined before the assembly. This procedure guarantees high reliability and life span of GEBA water pumps.
Product Features:
See More
Product Features:
- OE-Equivalent and direct fit application.
- 100% new with no remanufactured parts.
- High quality cast aluminum.
- Advanced bearing design for high axial and radial stresses.
- Unitized sealing technology that ensures optimal leak tightness and longevity.
- Optimum cooling performance and longevity.
APA/URO – APA/URO Expansion Tank Hose (Part No.G203032108APA)
from
$10.40
All APA/URO rubber coolant hoses are pre-shaped and double reinforced for extra strength and durability. Each hose is manufactured from ECD (Electro Chemical Degradation) resistant materials, which prevents electrolysis from breaking down the rubber from the inside out. All APA/URO cooling components are made to meet or exceed OE standards.
Product Features:
See More
Product Features:
- All cooling-water hose inner linings are resistant to electrochemical cracking
- high strength and resistance to oil, mud, salt, road debris, and ozone
- Resistance to distilled water and water ethylene glycol mixtures
- Resistance to air temperatures of up to 125C
Factory Air – Green Round O-Ring (Part No.24650)
from
$1.99
Made from HNBR material; Compatible with R12 And R134A; High quality construction; Universal applications
See More
Behr – Expansion Tank Cap (Part No.G104023472BEH)
from
$40.34
The Behr Expansion Tank Cap is a high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.
Product Features:
See More
Product Features:
- Premium Original Equipment replacement
- Provides performance and dependability
- Manufactured to meet OE specifications
Mr. Gasket – Thermocap Radiator Cap (Part No.2471B)
from
$46.99
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.
Product Features:
See More
Product Features:
- Indicates coolant temperature
- Helps prevent coolant injuries
- Fahrenheit and centigrade readings
- Color-coded temperature ranges
- Integrated coolant reclamation valve
- Improves under-hood appearance
- Chromed crown with a colored trim ring
Carquest Premium – Standard Thermostat: 160 Degrees (Part No.13376)
from
$10.99
Carquest Premium Thermostats are manufactured with OEM quality materials and safety standards by an OE Supplier. This thermostat will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable.
Product Features:
See More
Product Features:
- High grade stainless steel and copper construction
- Meets or exceeds OEM standards
- Consistent and precise response to cooling system needs
- Original equipment design for worry-free direct fit replacement
- 100% tested and calibrated
Carquest Premium – Engine Coolant Temperature Switch (Part No.ACA1576)
from
$12.29
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More
Carquest Premium – New Compressor with Clutch, Nippondenso 10P15E (Part No.T58343)
from
$827.99
Carquest Premium A/C compressors are 100% new units that are manufactured to the highest quality to meet or exceed OE specifications.
Product Features:
See More
Product Features:
- Every unit is 100% function and leak tested
- Tested for noise, vibration, durability, vacuum decay and pressure decay to ensure no leaks and longer life
- Very low friction coating used on swash plate to improve durability
- PTFE coated pistons improve performance and reduce wear
- Rubber dampened clutch plate ensures smooth clutch engagement and reduces wear
- Matched high-quality needle-roller bearing ensures low friction and high load capability
- Limited Lifetime Warranty when following warranty requirements: Flush A/C System, replace accumulator/receiver dryer, replace orifice tube/expansion device, and filling with correct oil and refrigerant
Permatex – Sensor-Safe, High-Torque RTV Silicone Gasket Maker (Part No.82194)
from
$11.49
Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.
Product Features:
See More
Product Features:
- High torque and rigidity
- Sensor-safe, non-corrosive formula
- OEM specified
- Low-odor, non-corrosive formula
- Ideal for closed spaced bolt patterns
Carquest Premium – Multi Purpose Relay (Part No.RAA1246)
from
$30.49
Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More
Carquest Premium – A/C Filter Drier (Part No.T33321)
from
$23.99
Carquest Accumulators and Receiver Driers are designed to store, filter and dry the air conditioning refrigerant to provide proper performance and durability for the air conditioning system. They are manufactured to meet or exceed original equipment specifications.
Product Features:
See More
Product Features:
- All parts meet or exceed original equipment standards for moisture absorption, pressure and temperature resistance, air tightness, vibration resistance, corrosiveness, and pulse pressure.
- Desiccant is 100% tested and assembled in a controlled environment to ensure performance meets or exceeds original equipment standards.
- All accumulators and receiver driers are helium leak tested prior to packaging.
- O-Rings necessary for installation are included.
- O-Rings necessary for installation are included.
Santech – A/C Pressure Switch (Part No.R1054178181SII)
from
$18.63
A/C Pressure Switch
Carquest Premium – Radiator Cap Tester Adapter (Part No.12552)
from
$14.29
Tester adapter for the MT-300 cooling system pressure testers. Professional grade test equipment to ensure an automotive cooling system is operating at the correct pressure. Made from high quality materials to ensure durability. Designed to test automotive coolant caps.
Product Features:
See More
Product Features:
- Machined metal construction
- Works with MT-300 pressure tester
- Tests coolant caps
- Professional quality
Factory Air – Cap & Valve A/C System Seal Kit (Part No.26777)
from
$16.99
High quality OE replacement part with all components needed to complete the job
Product Features:
See More
Product Features:
- All the seals needed to complete the job
- Compatible with both R12 and R134a refrigerants
- SUV and rear air applications
- Application specific
Factory Air – Green Round O-Ring (Part No.24608)
from
$1.99
Made from HNBR material; Compatible with R12 And R134A; High quality construction; Universal applications
See More
Factory Air – Green Round O-Ring (Part No.24610)
from
$0.99
Made from HNBR material; Compatible with R12 And R134A; High quality construction; Universal applications
See More
Popular 1988 Porsche 944 Cooling and Climate Controls Categories
1988 Porsche 944 Cooling and Climate Controls
You count on your 1988 Porsche 944 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Cooling and Climate Controls. With 51 Cooling and Climate Controls ranging in price from $0.99 to $827.99, you’re sure to find everything you need for your 1988 Porsche 944.
Brands matter. If you want to shop a specific Cooling and Climate Controls brand, we stock 21 different brands like Permatex, Carquest Premium, and Factory Air. 1988 Porsche 944 Cooling and Climate Controls start as low as $0.99!
One of the best ways to find top quality OEM or aftermarket Cooling and Climate Controls is by asking professionals. Short of that, you can shop with confidence thanks to our 1,815 extensive product reviews on 1988 Porsche 944 Cooling and Climate Controls. Some of the top-rated Cooling and Climate Controls products we carry are Thermocap Radiator Cap with 3.2 stars and Cap & Valve A/C System Seal Kit with 4.2 stars.
Did we mention you can order your Cooling and Climate Controls from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Cooling and Climate Controls inventory for your 1988 Porsche 944 below to get started!
Top-Rated Cooling and Climate Controls Brands For Your 1988 Porsche 944
Trusted Cooling and Climate Controls OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1988 Porsche 944 running right for years to come. In our inventory you’ll find brands like Permatex, Carquest Premium, Factory Air, and even more.
Popular Permatex Cooling and Climate Controls
You’ll find popular Permatex brand products across Engine Cooling Parts. All are waiting to get your 1988 Porsche 944 back on the road. Some of the top-rated Permatex products in these categories are:
from
$19.99
(2)
The Right Stuff: 1 Minute Gasket Maker: Grey, 3 OZ
Engine Water Pump Inlet Pipe Gaskets
from
$6.99
(9)
Sensor-Safe, High Torque RTV Silicone Gasket Maker
Engine Water Pump Inlet Pipe Gaskets
Top-Rated Cooling and Climate Controls
If are what you’re looking for, our inventory holds plenty. We stock brand Cooling and Climate Controls for your 1988 Porsche 944, and some of our most reviewed parts include:
from
$6.99
(288)
Water Pump & Thermostat RTV Silicone Gasket Maker, 0.5 OZ
Engine Water Pump Inlet Pipe Gaskets
FAQs for 1988 Porsche 944 Cooling and Climate Controls
What are the most purchased Cooling and Climate Controls for the 1988 Porsche 944?
Out of 51 Cooling and Climate Controls for the 1988 Porsche 944, the most popular in our inventory are:
What are the top-rated 1988 Porsche 944 Cooling and Climate Controls?
Top-rated Cooling and Climate Controls for your 1988 Porsche 944 based on customer reviews/ratings are:
from
$47.99
(17)
Thermocap Radiator Cap
“Worth the money if only for the looks. And will tell you the temp outside”
from
$11.99
(5)
Standard Thermostat: 180 Degrees
“solved a problem on my sons car that was misdiagnosed by someone else as a bad head gasket. On this car the overflow tank feeds the thermostat housing”
