1988 Pontiac Firebird Torque Converter and Related Products

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

• Fluid Balanced

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

• Fluid Balanced

HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• New Turbine Hub
• New Springs/Rollers In Stator

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

• Fluid Balanced

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

• Fluid Balanced

HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.

Product Features:

• 2300-2500 RPM
• Small And Big Blocks
• Mild To Serious Performance
• Furnace Brazed
• Fully Balanced

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

• Fluid Balanced

You can forget about the problem of shearing a torque converter bolt after you install these super strong 200,000 Pounds Per Square Inch gems. They are designed for each specific application and provide the optimum grip. Kits come with hardened parallel ground washers.

Product Features:

• Provides The Optimum Grip
• Kits Come With Hardened Parallel Ground Washers
• Made In USA
• 1/2” Thick Tabs
• 7/16″-20 Thread Size
• Sold As A Kit
• 1.25″ Underhead Length

You can forget about the problem of shearing a torque converter bolt after you install these super strong 200,000 Pounds Per Square Inch gems. They are designed for each specific application and provide the optimum grip. Kits come with hardened parallel ground washers.

Product Features:

• Super Strong, Rated At 200,000 PSI
• Kits Come With Hardened Parallel Ground Washers
• Delivers ARP Quality And Reliability
• Made In USA
• 0.590″ Underhead Length
• M10 X 1.5 Thread Size
• Set of 3

ARP torque converter bolts are manufactured from 8740 chromoly steel and feature 200,000 psi tensile strength. Add a set to your drivetrain, and shearing torque converter bolts are a thing of the past.

Product Features:

• 5/8″ 12-Point, 5/8″ Hex Socket Size(s)
• 8740 Chromoly
• Black Oxide
• Chevrolet, Powerglide, TH350 & TH400, With Most Aftermarket Converters
• 0.725″ Underhead Length
• 7/16″-20 Thread Size
• Sold As A Kit

You can forget about the problem of shearing a torque converter bolt after you install these super strong 200,000 PSI gems. They are designed for each specific application and provide the optimum grip. Kits come with hardened parallel ground washers.

Product Features:

• Super Strong, Rated At 200,000 PSI
• Designed For Specific Applications
• Delivers ARP Quality And Reliability
• Made In USA
• 0.750″ Underhead Length
• 3/8″-24 Thread Size
• Sold As A Kit

This automatic transmission torque convertor connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this automatic transmission torque connector matches the appearance and function of the factory hardware on specified applications
• Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience