from

$215.99

Prebent pipe kits. Flowmaster’s 16 gauge mandrel bent pipe kits are designed to fit perfectly onto your vehicle with all the quality and performance that you would expect from Flowmaster.

from

$56.99

Made from quality materials for durability, DynoMax® pipe is manufactured with precision benders and fixture checked to ensure a precise fit for quick and easy installation.

Product Features:

IMPROVED FLOW CAPACITY — Mandrel bends (where applicable) improve flow capacity over traditional bends while increased pipe diameter from OE sizes increases flow and power
DESIGNED TO PERFORM — Fixture checked to ensure a precise fit for quick and easy installation
AVAILABLE IN DIFFERENT SIZES — Offered in a variety of styles and sizes for a quality vehicle repair
PREMIUM MATERIALS – Made from aluminized steel for durability and long life
BETTER TOGETHER — Use premium DynoMax® accessories when installing DynoMax mufflers and exhaust systems for a complete performance exhaust system upgrade

from

$20.99

Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.

Product Features:

Manufactured from high-temperature acrylic blend exhaust material
Provides excellent sealing and durability
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Resists Deteriorating
Provides Excellent Torque Retention

from

$38.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$49.49

Multi-Layered Steel (MLS) exhaust and header collector gaskets are designed for extreme cylinder pressures produced by high horsepower high compression turbo-charged, supercharged and nitrous oxide injected engines. Manufactured from three stainless steel layers, they resist corrosion, will not burn through or push out and maintain maximum fastener torque retention. Stress formed inner and outer layer embossments act like springs that rebound under exhaust flange clamp load, creating force to seal extreme exhaust pressures. Total gasket thickness .075 inch. Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.

Product Features:

Multi Layer Stainless Steel 3-Layers
Round Port 1.75″ Diameter
Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.
Thickness .072″
Fits GM LS Series Engines 1997-’15

from

$17.79

Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.

Product Features:

Tear Resistant
Precisely Cut To Match Header

from

$59.19

Mr. Gasket CopperSEAL Header Gaskets are a high quality copper gasket that performs extremely well and are reusable. We recommend this in all racing and high performance applications. They are for stock heads unless indicated, and work well in high heat and turbocharged applications.

Product Features:

Manufactured from ¿Dead Soft¿ (solid) .043″ thick copper material
Manufactured from ┐Dead Soft┐ (solid) .043″ thick copper material
.051″ embossment around each exhaust port to seal irregular surfaces. Total gasket thickness .094″
Provides excellent sealing and durability
Conforms to and seals minor surface irregularities
For high performance street, drag race, oval track and turbocharged (extreme heat) applications
Ideal For Tow Vehicles
Ideal For Motorhomes

from

$113.99

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four-inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$99.99

The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$215.99

Aero Chamber Muffler

from

$151.99

Product Features:

Aluminized Steel Construction
3in. Inner Pass Tubes
Reduce Backpressure
Increase Horsepower
No Glass To Burn Or Blow Out
Will Flow In Either Direction
Welded For Strength/Durability

from

$165.99

The 80 series is a cross-flow design for applications where the muffler is mounted transversely behind the rear end. Delivering an aggressive muscle car sound both inside and outside the vehicle, this is an excellent replacement for Camaros & Firebirds with transverse mufflers. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$38.49

Original equipment style bracket in high quality chrome for years of service. Includes hardware.

Product Features:

Chrome Plated Heavy Gauge Steel
Can Be Used For Other Applications
Looks Better Than Painted
Hardware included

from

$25.99

Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

Product Features:

Chrome Plated Steel
F-Style
Heavy Gauge Steel Construction
Fits Small Block Chevy 265-400 CID
Must Be Used With Part 9852

from

$19.29

These brackets are made from heavy gauge steel, polished to a high luster, then chrome plated. Similar in design to OEM units, these brackets can be adapted to other engines.

Product Features:

Chrome plated
Similar to OEM design
May be adaptable to other applications

from

$41.99

Made of high quality stainless steel. These bolts will brighten up your hot rod, or improve the looks of your race car.

Product Features:

Bright Ball Burnish Finish
Made From 304 Stainless
Compact Hex Head Is Ideal Where Space Is Limited
12 Per Set
Resist corrosion and provides a clean professional appearance

from

$122.99

Made from quality materials for durability, DynoMax® pipe is manufactured with precision benders and fixture checked to ensure a precise fit for quick and easy installation.

Product Features:

IMPROVED FLOW CAPACITY — Mandrel bends (where applicable) improve flow capacity over traditional bends while increased pipe diameter from OE sizes increases flow and power
DESIGNED TO PERFORM — Fixture checked to ensure a precise fit for quick and easy installation
AVAILABLE IN DIFFERENT SIZES — Offered in a variety of styles and sizes for a quality vehicle repair
PREMIUM MATERIALS – Made from aluminized steel for durability and long life
BETTER TOGETHER — Use premium DynoMax® accessories when installing DynoMax mufflers and exhaust systems for a complete performance exhaust system upgrade

from

$234.99

Dynomax® Performance Exhaust, a leading performance exhaust brand built on over 20 years of market leadership. Each and every Dynomax® product is backed by engineers who know what you want and expect out of a performance exhaust product.

Product Features:

DynoMax® Universal ‘Y-Pipes’ feature O.D. sized inlet and outlets allowing for easy fabrication of custom exhaust systems. Manufactured using 16 gauge aluminized coated steel
Mandrel bends improve flow capacity over traditional bends
Combine state-of-the-art engineering with quality material to provide exceptional strength and durability
Dynomax® premium pre-bent pipe is manufactured with precision benders, and then fixture checked, insuring every part is a perfect fit, providing quick and easy installation.
Pipe diameters are increased from OEM sizes to improve flow and increase power