1988 Nissan Sentra Ignition and Tune-Up Products

Essential 1988 Nissan Sentra Ignition and Tune-Up Products

NGK – Spark Plug Wire Set (Part No.8111)

Spark Plug Wire Set

from

$152.99
NGK variable pitch resistor cables provide uniform resistance and ensure outstanding electrical conductivity in high-quality cables. Outer EPDM/silicone jacket and inner insulation contain high voltage currents for excellent dielectric strength. NGK varia

Product Features:
  • PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
  • BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
  • STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
  • PREMIUM ALLOY WINDING: Variable pitch winding over Ferrite magnetic alloy coating delivers ultra low resistance and excellent interference protection
  • CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier
See More

NGK – Ignition Wire Set (Part No.F1020115953NGK)

Ignition Wire Set

from

$39.09
NGK Resistor Spark Plug Wire Sets utilize a construction method known as variable pitch wire winding to create resistance to radio frequency interference. The variable pitch winding (loose/tight/loose) provides suppression throughout a very wide range by scrambling and breaking up the electrical waves radiated by the firing of the spark plugs. A ferrite magnetic layer consisting of a mixture of rubber, plastic and powdered ferrite magnetic materials, offers uniform resistance and unsurpassed conductivity. NGK wires have a lower resistance than conventional carbon core wires (8k ohm/meter versus 16k ohm/meter). This comparison is important to remember when you consider that many manufacturers recommend wires be replaced when the resistance exceeds 20k ohm/meter. This does not leave much margin for wear when the wire may only meet original standards at the very early stages of its life.

Product Features:
  • OE-Equivalent.
  • OEM style connectors for easy Installation.
  • Superior Firing and Fuel Savings
  • Outstanding Durability and Performance
  • Excellent Noise Suppression
  • Numbered for easy cylinder identification.
  • High quality EPDM and Silicone coverings.
See More

Carquest Premium – Coil On Plug Insulator Boot: Spring included, Designed for direct fit (Part No.35-7091)

Coil On Plug Insulator Boot: Spring included, Designed for direct fit

from

$15.99
CARQUEST Premium coil on plug boots are engineered to restore ignition boot reliability and performance. We have OE design providing an exact direct fit for your application and the performance and durability meet or exceed OE requirements. It offers excellent heat resistance as well as maximum protection against spark loss. With durable silicone compound for resistance to high heat or abrasion.

Product Features:
  • Provides excellent heat resistance as well as maximum protection against spark loss.
  • Durable silicone compound for resistance to high heat or abrasion
  • Spring included with the coil boot
  • Design for direct compatibility
  • OE design provides an exact fit for your application
  • Multipack provides one time replace all COP for better deal
See More

NGK – Spark Plug Wire Set (Part No.8104)

Spark Plug Wire Set

from

$72.99
NGK variable pitch resistor cables provide uniform resistance and ensure outstanding electrical conductivity in high-quality cables. Outer EPDM/silicone jacket and inner insulation contain high voltage currents for excellent dielectric strength. NGK varia

Product Features:
  • PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
  • BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
  • STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
  • PREMIUM ALLOY WINDING: Variable pitch winding over Ferrite magnetic alloy coating delivers ultra low resistance and excellent interference protection
  • CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier
See More

NGK – Coil on Plug Boot (Part No.58999)

Coil on Plug Boot

from

$8.99
NGK Coil on Plug Boots are built to stringent OEM tolerances, combining original equipment fit, design and outstanding durability. NGK Coil on Plug Boots are manufactured using only premium silicone and always include any required internal springs and ferrite resistors for superior performance and RFI noise suppression. Bridging the important link between ignition coil and spark plug, COP boots should always be replaced with NGK Coil on Plug Boots at the time as changing spark plugs to prevent ignition problems such as flashover.

Product Features:
  • PREMIUM GRADE SILICONE: Designed to withstand harsh environments
  • OEM MATCHED: Includes all required internal springs and ferrite resistors for superior performance and RFI noise suppression
See More

Carquest Premium – Spark Plug Wire Set: 5 Wires, Increased performance, Designed for direct fit (Part No.35-4240)

Spark Plug Wire Set: 5 Wires, Increased performance, Designed for direct fit

from

$66.99
Product Features:
  • SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
  • Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
  • 100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
  • EPDM inner insulation stops power-robbing voltage leaks.
  • With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
  • Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
  • Excellent interference suppression and consistent performance
  • Easy lock terminals for more convenient installation.
  • Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
  • Broad coverage available for most vehicles on the road today
  • Include grease pack to ensure easy installation and removal
See More

Carquest Premium – Distributor Cap and Rotor Kit (Part No.CAC2015)

Distributor Cap and Rotor Kit

from

$20.79
Distributor Cap and Rotor Kit

Carquest Premium – Distributor Cap and Rotor Kit (Part No.CAC1874)

Distributor Cap and Rotor Kit

from

$18.29
Distributor Cap and Rotor Kit

Carquest Premium – Distributor Cap and Rotor Kit (Part No.CAC1971)

Distributor Cap and Rotor Kit

from

$20.79
Distributor Cap and Rotor Kit

Carquest Premium – Distributor Rotor (Part No.DAA1332)

Distributor Rotor

from

$12.99
Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

YEC – YEC Distributor Rotor (Part No.F2020227237YEC)

YEC Distributor Rotor

from

$24.90
YEC Distributor Caps and Rotors are made from top quality materials throughout to ensure high performance and long product life.

Product Features:
  • Superior Surface Finish
  • RFI Suppression
  • Precision-machined Contacts
  • Finely -tooled Metal Mounting Sleeve
See More

Carquest – Distributor Rotor (Part No.23A1013)

Distributor Rotor

from

$10.49
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:
  • High-quality products that meet OE appearance and performance to
See More

Champion – Iridium Spark Plug: Maximum Performance, OE Replacement, RC12WYPB4 (Part No.9201)

Iridium Spark Plug: Maximum Performance, OE Replacement, RC12WYPB4

from

$8.49
Champion® Iridium – the ultimate element. This spark plug’s fine-wire iridium center and platinum ground electrodes provide the sharpest spark focus for maximum performance.

Product Features:
  • Champion Iridium – Maximum Performance. Premium Spark Plug
  • Iridium center electrode delivers maximum life
  • Fine-wire center electrode and V-trimmed for greater ignitability
  • V-trimmed ground electrode promotes sharper spark focus
  • Maintains stable operating temperature under all engine loads
  • Heat-Active™ alloy allows electrodes to reach optimal temperature quickly
See More

DENSO – U-Groove Spark Plug: OE Performance, lasts 30K+ Miles, K16PR-U11 (Part No.3130)

U-Groove Spark Plug:  OE Performance, lasts 30K+ Miles, K16PR-U11

from

$2.99
The unique U-Groove ground electrode is one of the finest features of DENSO spark plugs. The electrode was developed to meet the demand for improved ignitability, necessary for increased efficiency in emission gas purification and fuel consumption.

Product Features:
  • Patented U-groove ground electrode design fires leaner mixtures than conventional plugs
  • Precision machine-rolled threads reduce seizing and cross-threading in delicate aluminum heads
  • Wide range of part numbers for thousands of applications, including classic and collector cars
  • Lasts twice as long as most conventional plugs
  • 100% pre-fired to assure reliable operation
  • U-Groove Conventional
See More

Champion – Copper Plus Spark Plug: Dependable Performance, OE Replacement, REC12MCC4 (Part No.446)

Copper Plus Spark Plug: Dependable Performance, OE Replacement, REC12MCC4

from

$4.99
Dependable performance. This Champion spark plug features a copper core electrode that provides increased conductivity and heat control for good overall wear.

Product Features:
  • Copper Plus – Dependable Performance.
  • Copper core center electrode allows for accurate control of heat range for longer life
  • Patented TinTac and ULTRASEAL coated shell for maximum corrosion resistance
  • Patented SAC-9 semiconductor resistor for maximum EMI & RFI suppression
  • Built to ISO and SAE standards for proven performance
See More

Carquest Premium – Ignition Module (Part No.CBE1213)

Ignition Module

from

$115.99
CARQUEST Ignition Modules are built by an ignition systems manufacturer with expertise in the entire vehicle spark system.

Product Features:
  • CARQUEST Ignition Modules creates and refines the timing of the engine using various sensors and readings throughout the spark system in order to create an efficiently running engine.
  • CARQUEST Ignition Modules use current and voltage limiting circuitry in order to prevent the ignition coil from over voltage/current. Over voltages can allow for coils to create excessive heat which can damage to the ignition module resulting in check eng
  • CARQUEST Ignition Modules are 100% individually tested for all product functionalities including over voltage, timing and dwell.
See More

Carquest – Ignition Control Module (Part No.CBE624)

Ignition Control Module

from

$64.05
Intermotor® is a complete engine management import line that includes ignition and electrical relays, switches and sensors with a concentration on high technology categories such as computerized engine controls, fuel injection, and emission controls with coverage for every part number with an import nameplate. Intermotor® parts are unrivalled for quality, original fit, form, function, and coverage providing a genuine import part in every box. Intermotor® is the import leader by design.

Product Features:
  • Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment
  • Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module
  • Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather
  • High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability
  • Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C
See More

Carquest Premium – Ignition Module (Part No.CBE1106)

Ignition Module

from

$99.99
CARQUEST Ignition Modules are built by an ignition systems manufacturer with expertise in the entire vehicle spark system.

Product Features:
  • CARQUEST Ignition Modules creates and refines the timing of the engine using various sensors and readings throughout the spark system in order to create an efficiently running engine.
  • CARQUEST Ignition Modules use current and voltage limiting circuitry in order to prevent the ignition coil from over voltage/current. Over voltages can allow for coils to create excessive heat which can damage to the ignition module resulting in check eng
  • CARQUEST Ignition Modules are 100% individually tested for all product functionalities including over voltage, timing and dwell.
See More

Carquest Premium – Ignition Coil: Meets or Exceeds Original Equipment Specifications, 1 Piece (Part No.EBC1108)

Ignition Coil: Meets or Exceeds Original Equipment Specifications, 1 Piece

from

$107.99
Carquest Premium ignition coils meet or exceed original equipment (OE) specifications and are developed by top OE/OES manufacturers to ensure superior performance. All of our Carquest Premium ignition coils are developed by IATF 16949 certified manufacturers for consistent durability and long-lasting performance. These ignition coils use high-quality components and will utilize optimized designs on applications where the OE ignition coil had frequent failures. We require stringent testing standards to ensure proper fit and performance for each application and stand behind our Carquest Premium ignition coils with an industry-leading warranty. Carquest Premium ignition coils are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.

Product Features:
  • Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
  • 100% pure copper precision-wound windings increase coil life and ensure reliability and maximum coil output when needed.
  • Highly conductive aluminum alloy secondary terminal guarantees secondary coil terminals will not oxidize (rust), will provide excellent conductivity, extended coil life and will not cause excessive stress on the primary control circuit.
  • 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
  • 100% end-of-line tested to ensure confidence and product reliability, every time.
See More

Hitachi – Ignition Coil Actual OE Part – New (Part No.IGC0054)

Ignition Coil Actual OE Part - New

from

$88.99
Hitachi’s Ignition Coils (IGCs) provide the needed energy for today’s high efficiency, high power vehicles. High quality materials ensure that even under the most extreme conditions, Hitachi’s IGCs will not deform or malfunction. Our ignition coils help to produce optimal engine efficiency resulting in reliable performance and gas mileage. Electronic connection points are welded to providing durability during heat cycles. Details such as materials, high turns ratios, and protected circuitry provide a durable and reliable product approved by OE manufacturers. Designed to meet the exact needs of each specific vehicle, Hitachi’s ignition coils are the premium choice.

Product Features:
  • Benefits of these quality Ignition Coils include efficient spark and reduced need for wires, long product life, and consistent voltage and amperage output.
See More

Delphi – IGNITION COIL (Part No.GN10245)

IGNITION COIL

from

$112.99
Delphi OE technology ignition products are validated to match the vehicles system; OE quality replacement parts for the right fit , form and function; Delphi coils provide OE performance, durability and electromagnetic capacity level requirements.

Product Features:
  • Delphi coils provide OE performance, durability and electromagnetic capacity level requirements
  • Delphi ignition coils are designed to operate as part of an integral engine management system to insert power into spark plugs and ensure fast starts; consistent engine performance and optimized fuel efficiency
  • Delphi uses winding process techniques to control the length of wire between adjacent windings; that’s important since more length means greater voltage differences and can create more pressure that could break down the insulation and wire coating
  • We back our ignition coil design with proven materials, such as high quality wires and wire coating that resists the cracks, pin holes and imperfections that most often lead to failure issues
See More

Dorman – Help – Spark Plug Non-Foulers – 14mm Gasket Seat Long Reach (Part No.42004)

Spark Plug Non-Foulers - 14mm Gasket Seat Long Reach

from

$9.99
This spark plug non fouler is designed for easy installation on specified vehicles to protect spark plugs from fouling and damage. It is engineered for durability and reliable performance.

Product Features:
  • Direct replacement – this spark plug non fouler is designed for easy installation to protect spark plugs from fouling and damage on specified vehicles
  • Ideal solution – this non-fouler preserves spark plug life and is a reliable replacement for an original non-fouler that has failed due to corrosion
  • Durable construction – made from quality components to ensure reliable performance and a long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Carquest – Ignition Switch (Part No.CS333)

Ignition Switch

from

$34.05
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:
  • Designed to OE standards for ease of installation
See More

Carquest – Ignition Switch (Part No.CS770)

Ignition Switch

from

$74.99
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:
  • Designed to OE standards for ease of installation
  • Copper alloy conductors ensure superior electrical conductivity with low resistive losses
  • Our parts are 100% tested to verify both mechanical and electrical switching performance
  • Robust design and high grade materials meet the stringent demands of today’s service professional
  • BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product
See More

Original Equipment – Ignition Switch (Part No.M5050152756OEA)

Ignition Switch

from

$48.88
Ignition Switch

Carquest Premium – Ignition Switch (Part No.CSA1804)

Ignition Switch

from

$48.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

Original Equipment – Ignition Switch (Part No.M5050143252OEA)

Ignition Switch

from

$52.90
Ignition Switch

Carquest Premium – Ignition Switch (Part No.CSA1655)

Ignition Switch

from

$30.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

1988 Nissan Sentra Ignition and Tune-Up Products

You count on your 1988 Nissan Sentra to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Ignition and Tune-Up Products. With 34 Ignition and Tune-Up Products ranging in price from $2.49 to $99.99, you’re sure to find everything you need for your 1988 Nissan Sentra.

Brands matter. If you want to shop a specific Ignition and Tune-Up Products brand, we stock 12 different brands like E3, AC Delco, and Autolite. 1988 Nissan Sentra Ignition and Tune-Up Products start as low as $2.49!

One of the best ways to find top quality OEM or aftermarket Ignition and Tune-Up Products is by asking professionals. Short of that, you can shop with confidence thanks to our 61 extensive product reviews on 1988 Nissan Sentra Ignition and Tune-Up Products. Some of the top-rated Ignition and Tune-Up Products products we carry are PW16TT Platinum TT Spark Plug with 3.4 stars and OE Series V-Power Nickel Spark Plug: V-Groove Tip Design, BPR6EY-11 with 5.0 stars.

Did we mention you can order your Ignition and Tune-Up Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Ignition and Tune-Up Products inventory for your 1988 Nissan Sentra below to get started!

Top-Rated Ignition and Tune-Up Products Brands For Your 1988 Nissan Sentra

Trusted Ignition and Tune-Up Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1988 Nissan Sentra running right for years to come. In our inventory you’ll find brands like E3, AC Delco, Autolite, and even more.

Popular ACDelco Ignition and Tune-Up Products

You’ll find popular ACDelco brand products across Spark Plugs. All are waiting to get your 1988 Nissan Sentra back on the road. Some of the top-rated ACDelco products in these categories are:
Spark Plug
from $4.99
(3)
Spark Plug
Spark Plugs

Top-Rated Ignition and Tune-Up Products


If are what you’re looking for, our inventory holds plenty. We stock brand Ignition and Tune-Up Products for your 1988 Nissan Sentra, and some of our most reviewed parts include:

FAQs for 1988 Nissan Sentra Ignition and Tune-Up Products

What are the most purchased Ignition and Tune-Up Products for the 1988 Nissan Sentra?

Out of 34 Ignition and Tune-Up Products for the 1988 Nissan Sentra, the most popular in our inventory are:
Rapidfire Spark Plug
from $6.79
This product is not rated
Rapidfire Spark Plug
Spark Plugs

What are the top-rated 1988 Nissan Sentra Ignition and Tune-Up Products?

Top-rated Ignition and Tune-Up Products for your 1988 Nissan Sentra based on customer reviews/ratings are:
PW16TT Platinum TT Spark Plug
from $5.79
(7)
PW16TT Platinum TT Spark Plug
“Fast and easy, plus you accept PayPal”
OE Series V-Power Nickel Spark Plug: V-Groove Tip Design, BPR6EY-11
from $4.79
(5)
OE Series V-Power Nickel Spark Plug: V-Groove Tip Design, BPR6EY-11
“Purchased these plugs from Hinson’s Car Quest. They worked perfect. The staff was so much more friendly than other stores I go to. Will definitely be ”
G-Power Spark Plug: Single Platinum Tip Design, BPR6EGP
from $5.49
(5)
G-Power Spark Plug: Single Platinum Tip Design, BPR6EGP
“My favorite spark plug for the 1993 Volvo 240. A significant improvement over the basic copper plug at a nominal increase in price. I change them ever”