1988 Mercury Grand Marquis Differentials

Product Features:

• Brand may vary by location

Yukon outer stub axle for Chrysler 9.25″ front. This axle uses a 1485 u/joint and has 33 splines.

Product Features:

• Fits Ford 8.8″
• Steel

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

• Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
• Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
• Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
• Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

The tremendous shock loads generated at launch by most any drag racing vehicle equipped with today sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. they are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.

Product Features:

• Forged From Premium Grade 8740 Chrome Moly Steel
• Heat Treated
• Nominally Rated At 200,000 Psi Tensile Strength
• Specially Hardened, Precision Ground Washers
• 0.75″ Underhead Length
• 200,000 PSI
• Sold As A Set

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Ford 9″ with LM603011 carrier races and Daytona pinion support
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, pilot bearing, thread locker, marking compound with brush and gasket.

Product Features:

• Fits Ford 9″ with 28 spline axles
• Installs into a standard open carrier case
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Pinion gear thrust washer (0.875″ shaft) for 8.8″ Ford.

Product Features:

• Pinion gear thrust washer for Ford 8.8″
• 0.875″ diameter cross pin shaft applications only

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Ford 8.8″
• Includes carrier bearings and races and “super” carrier shim kit

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with Daytona pinion support
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M802011 race
• All steel construction

9″ large solid pinion preload spacer & shim kit for 35 spline pinion.

Product Features:

• Crush sleeve eliminator kit for Ford 9″ with 35 spline pinion

Product Features:

• Trac Loc spring
• Fits 28 spline Ford 8.8

9″ Ford gasket.

Product Features:

• Dropout gasket
• Fits Ford 9″

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

• Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles
• Quality materials – all components are built for reliable longevity and performance
• Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
• Trustworthy quality – backed by team of designers and engineers in the United States

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Product Features:

• FRD 10BLT 9.0 R/P 4.86 MGP

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

• Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

Spindle nut washer for Dana 28, ’92 & down. This replaces Spicer part number 40075.

Product Features:

• Spider gear kit
• Fit Ford 7.5″ open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

• Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
• Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
• Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
• Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

Standard Open side gear thrust washer for 7.5″ Ford.

Product Features:

• Side gear thrust washer
• Fits Ford 7.5″

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! This unit has been approved for competition in NASCAR National & Touring series. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

• Fits Ford 9″ with 31 spline axles
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

• Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

Chrome Moly cross pin shaft for Mini-Spool for 9″ Ford HD.

Product Features:

• Cross pin shaft
• Fits Ford 9″
• Chromoly steel for added strength

8.75″ Chrysler & 9″ Ford preload shim kit.

Product Features:

• Preload shim kit for Ford 9″ and Chrysler 8.75″ with ’41’ and ’42’ case housing

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands of many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON*, DEXRON*-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

• Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

• 35 spline
• 8 x 3.96″ bolt pattern
• Cut to length design fits 40″-43.5″ applications
• Fits Dana Spicer 60, 70 and 80