1988 GMC K2500 Performance Engines

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Product Features:

• Timing Chain Only

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Steel core gasket construction
• Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
• Not intended for use in emission controlled vehicles.

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Manufactured from high quality machine finished aluminum, Spectre’s Throttle Body Spacers are engineered to improve engine performance. By providing added volume to the intake manifold and directing air through a tapered internal constriction, this spacer utilizes the Venturi effect to increase the speed of air flowing into your intake manifold. Spectre has designed a number of kits to fit a wide range of specific applications. Each kit includes the necessary gaskets and hardware to bolt directly to the factory components, making installation quick and easy.

Product Features:

• Includes the necessary gaskets and hardware to bolt directly to the factory components
• Each kit is designed for the applications listed
• Manufactured from high quality machine finished aluminum
• Can be installed in less than an hour using common hand tools with no drilling or cutting required
• Simple to install

Product Features:

• Replacement Gasket For PN[7070] Edelbrock Intake
• One Gasket Only

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:

• Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
• Best with aftermarket converters and more rear gear.
• Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

• Valve Spring Retainers for Use OE Cast Iron Heads
• Superior Quality Heat-Treated Steel
• Machined for Strength with Black Oxide Finish
• Finish Ensures Rust and Corrosion Protection

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

• Zinc plated to resist corrosion and provide a clean professional appearance
• Made from Grade 5 steel for strength and durability
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Allen (socket) Head
• Zinc Plated For Protection

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

• Chrome plated
• Grade 8
• 12-point head
• AN washers with no exposed shoulder for a professional appearance

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Die-cut for an excellent fit
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use

Product Features:

• Made of aluminum with a natural finish
• 100cc chambers with 290cc intake ports
• 2.19 in. intake and 1.88 in. exhaust valves
• Bare Cylinder Head
• Standard intake and exhaust port location

The Edelbrock #609719 E-Tec Cylinder Heads are replacements for 302, 327, 350 & 400 c.i.d. S/B Chevy engines with “Vortec-style” manifolds. They feature an LT1-style raised runner intake port design for increased air-flow and ultimate performance. A uniqu

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

• Twisted Snout Water Pump Design For Updated Style
• Street Performance
• Heavy Duty Shaft w/5/8 in. Pilot
• Six-Blade Stamped Steel
• Anti-Cavitation Impeller
• 100 Percent Leak Tested

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• New Turbine Hub
• New Springs/Rollers In Stator

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 3400-3800 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Grade 8 Steel

These Magnum Roller Rocker Arms for Chevy V8 265-400 and V6 200-262 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.52 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed

Product Features:

• Roller tip reduces friction while stiff design and superior ratio accuracy yield more effective valve lift
• For applications with less than 350 lbs. of open spring pressure
• Constructed from 8620 chromemoly steel, a superior material that will not flex and ensures maximum lift
• Ultimate street roller rocker arm designed for serious performance enthusiasts

Product Features:

• Case-Hardened Tubing
• Welded Ends
• 5/16 in. Diameter
• Use with or without Hardened Steel Guideplates

Product Features:

• Case-Hardened Tubing
• Surface Hardening
• Welded Ends
• 0.3125 in. Diameter
• Use with or without Hardened Steel Guideplates