from

$379.99

Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

Mount Can Be Clocked To Assist In Mounting
Downsized design helps clearance issues w/oil pans and exhaust
Ball bearing supported armature and pinion gear
3 Hp Motor Provides Power For High Compression Engines
Gear reduction of 4.4:1 improves torque for great cranking
Downsized design helps clearance issues
Mount can be clocked to assist in mounting

from

$18.99

Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:

Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$25.99

This Spectre Alternator Bracket Kit is a two piece set designed to fit Chrysler 318-340-360 small block engines. Featuring a triple chrome-plated finish and high quality steel construction, this kit is an OEM replacement that includes two pieces.

Product Features:

Fits small block Chrysler 318-340-360 engines
Manufactured from high quality steel
Kit includes two pieces
Features a triple chrome-plated finish
Factory replacement

from

$24.99

A true performance application component for cars, trucks, hot rod, for racing and competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

Made from HYPER-Flex Polyurethane
Firm Enough for Huge Amounts of Horsepower/Torque
Soft Enough Not to Transmit Vibration

from

$47.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$409.99

The award-winning Quarter Stick automatic shifter is designed to provide positive gear change control for street or racing transmission applications. Gated mechanism. NHRA/IHRA approved reverse lockout.

Product Features:

Forward and Reverse Shift Patterns
Chrome Plated Trigger for Detent Activity
Factory Neutral Safety Switch
Compact And Lightweight
Roller Detent with Shifter Pattern

from

$766.99

Product Features:

Designed For Carbureted V8s
Power Increases From 100-250 HP
Precision EDM Machined Spray Bars
Simple To Install

from

$455.99

The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.

Product Features:

Improved Combustion And Economy
Increased Spark Plug Life
Improved Cold Weather Starting
Maintenance Free Operation
Accurate Spark Timing
Self-Lubricating Bushings
Years Of Trouble-Free Service

from

$76.99

The Edelbrock #4495 Signature Series Valve Covers are designed for Chrysler 318-340-360 V8 ’65-91 applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:

Small Block Chrysler 318-360,65-91
Short
Chrome Steel
Set Of Two
Rubber Grommets For Breather

from

$36.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$521.99

Edelbrock part #21763 Performer intake manifold is designed for street 318-340-360 c.i.d. Chrysler V8’s. This manifold is not for use on marine engines used in salt water. Will not fit 1992 and later Magnum engines. This manifold offers a durable black po

Product Features:

Idle-5500 RPM Range
Dual Plane Type-4150 Style Flange
4.13 in. Front Height, 4.63 in. Center Height, 5.13 in. Rear Height
Black Powder Coated Finish
Non-EGR

from

$185.99

RngPnn

from

$28.99

Manufactured from high-density cork and rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement and high performance street.

Product Features:

One-piece design
Eliminates potential leaks
Prevents over tightening
Prevents torque loss

from

$52.99

Spectre’s Differential Covers are made to OEM specifications and are triple chrome plated for a lasting shine. Designed to protect the intricate moving parts of the differential, Spectre’s covers add an extra layer of protection to the vehicle’s underside. Featuring a 10-bolt design and fits 1961-1989 Chrysler cars with a 8-1/4 inch ring gear. Includes 10 SAE standard chrome bolts for installation. You’ll need to supply your own bolts if your application requires metric bolts.

Product Features:

10 bolt design cover
Bolts and gasket included
Triple chrome plated for a lasting shine
10 chrome 5/16 inch -18 x 3/4 inch differential cover bolts included

from

$357.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$48.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$149.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1962-up TF727 transmissions and all internally balanced Chrysler, Dodge and Plymouth V8 engines with 6-bolt crankshaft flange. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.00 or 11.125 inch converter mounting locations and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$48.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$33.99

Mr. Gasket has three types of exhaust gaskets–standard, Ultra Seal, and Copperseal. Use the standard for a stock rebuild and the Ultra or Copperseal for extra blowout protection.

Product Features:

Designed to provide excellent sealing and durability
Large fiber gasket material
Heat resistant
Reusable
Precision die cut for excellent fit
Limited warranty

from

$18.99

Oil Pan Bolt Kit

from

$25.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$42.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$42.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$41.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$1243.99

Designed for carburetor V8 engines. Power increases from 200 to 400 horsepower. Simple to install. Shorter spray bars. More even distribution across the plenum. A more balanced air and fuel ratio. Quicker response time.

Product Features:

Designed For Carbureted V8 Engines
Power Increases From 200-400_ HP
Simple To Install
Shorter Spray Bars
More Even Distribution Across The Plenum
A More Balanced Air/Fuel ratio
Quicker Response Time

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

from

$16.99

Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.

Product Features:

Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S

from

$71.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features: