1988 Chevrolet G30 Heater Hoses

Essential 1988 Chevrolet G30 Heater Hoses

ACDelco – Heater Hose Connecto (Part No.R3036209226ACD)

Heater Hose Connecto

from

$18.86
Heater Hose Connecto

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length (Part No.80403)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length

from

$11.99
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • Meets Type EC electro-chemical requirements as specified in SAE J1684
See More

Gates – Premium Molded Heater Hose (Part No.18909)

Premium Molded Heater Hose

from

$31.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 12 Inch Length (Part No.80412)

Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 12 Inch Length

from

$24.99
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • Meets Type EC electro-chemical requirements as specified in SAE J1684
See More

Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 25 Inch Length (Part No.80414)

Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 25 Inch Length

from

$12.99
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • Meets Type EC electro-chemical requirements as specified in SAE J1684
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length (Part No.86123)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length

from

$18.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 10 Inch Length (Part No.88352)

Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 10 Inch Length

from

$28.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 29 Inch Length (Part No.87716)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 29 Inch Length

from

$16.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Molded 90 Degree Heater Hose (Part No.28479)

Molded 90 Degree Heater Hose

from

$21.49
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.

Product Features:
  • Resists electrochemical degradation and water permeation
  • Use with heater hose connectors and bulk heater hose to create custom assemblies
  • Compatible for coolant, air and water applications
  • EPDM tube and cover, synthetic fiber reinforcement
  • SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
  • Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 19/32 Inch Diameter, 22 Inch Length (Part No.87717)

Molded Heater Hose; EPDM Rubber, 19/32 Inch Diameter, 22 Inch Length

from

$19.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Premium Molded Heater Hose (Part No.19670)

Premium Molded Heater Hose

from

$16.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 29 Inch Length (Part No.88450)

Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 29 Inch Length

from

$26.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Premium Molded Heater Hose (Part No.18908)

Premium Molded Heater Hose

from

$27.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Molded 90 Degree Heater Hose (Part No.28468)

Molded 90 Degree Heater Hose

from

$16.99
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.

Product Features:
  • Resists electrochemical degradation and water permeation
  • Use with heater hose connectors and bulk heater hose to create custom assemblies
  • Compatible for coolant, air and water applications
  • EPDM tube and cover, synthetic fiber reinforcement
  • SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
  • Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 25 Inch Length (Part No.80415)

Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 25 Inch Length

from

$20.29
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • Meets Type EC electro-chemical requirements as specified in SAE J1684
See More

Gates – Molded 90 Degree Heater Hose (Part No.28475)

Molded 90 Degree Heater Hose

from

$18.49
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.

Product Features:
  • Resists electrochemical degradation and water permeation
  • Use with heater hose connectors and bulk heater hose to create custom assemblies
  • Compatible for coolant, air and water applications
  • EPDM tube and cover, synthetic fiber reinforcement
  • SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
  • Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Molded 90 Degree Heater Hose (Part No.28466)

Molded 90 Degree Heater Hose

from

$19.29
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.

Product Features:
  • Resists electrochemical degradation and water permeation
  • Use with heater hose connectors and bulk heater hose to create custom assemblies
  • Compatible for coolant, air and water applications
  • EPDM tube and cover, synthetic fiber reinforcement
  • SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
  • Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Premium Molded Heater Hose (Part No.19604)

Premium Molded Heater Hose

from

$24.29
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

1988 Chevrolet G30 Heater Hoses

Maybe you’re in the middle of a full rebuild of that 1988 Chevrolet G30. Maybe you just need a couple of Heater Hoses. Either way, Advance Auto Parts has 5 different Heater Hoses in our inventory ranging from $16.99 to $27.49. That means you can find the exact parts or products you need to keep that 1988 Chevrolet G30 running smoothly.

Heater Hoses are only as good as their brand. We stock 3 different brands to make sure you have plenty of trusted parts to choose from for your 1988 Chevrolet G30. Dayco, ACDelco, and Gates are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Heater Hoses for your 1988 Chevrolet G30, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.

So if you’re in the market for aftermarket Heater Hoses to keep your 1988 Chevrolet G30 rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Heater Hoses Brands To Make Your 1988 Chevrolet G30 Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1988 Chevrolet G30 demands trusted brand parts and products to keep it running. Many trusted brands of Heater Hoses make up Advance Auto Parts’ inventory, and all are ready to help make your G30 the best it can be. Be sure to browse some of our top Heater Hoses brands and parts.

FAQs for 1988 Chevrolet G30 Heater Hoses

What are the most purchased Heater Hoses for the 1988 Chevrolet G30?

Out of 5 Heater Hoses for the 1988 Chevrolet G30, the most popular in our inventory are:
Heater Hose Connecto
from $18.86
This product is not rated
Heater Hose Connecto
Heater Hose Fittings
Premium Molded Heater Hose
from $24.29
This product is not rated
Premium Molded Heater Hose
Heater Hoses
Premium Molded Heater Hose
from $27.49
This product is not rated
Premium Molded Heater Hose
Heater Hoses