1987 International 1754 Belts and Hoses
More 1987 International 1754 Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1987 International 1754, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1987 International 1754 Belts and Hoses
Gates – Green Stripe« Heavy-Duty Straight Heater Hose (Part No.28442)
from
$6.49
Heavy-duty construction assures dependable operation in truck, bus and off-road equipment heater systems. For a maintenance free connection, install with Power-Grip SB clamps. Approved for marine applications.
Product Features:
See More
Product Features:
- Green Stripe construction provides best cost-per-mile economics
- Abrasion-resistant cover
- Engineered with materials to resist electrochemical degradation
- Reduces water loss from water permeating the hose wall and cover
- Exceeds SAE 20R1 Type EC (Class D-1 tube and cover Standard Wall)
- Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
- Note: For a maintenance free connection, use PowerGrip SB clamps
- Caution: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Gates – Premium Molded Coolant Hose (Part No.21461)
from
$23.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Premium Molded Coolant Hose (Part No.21042)
from
$42.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 20.50" Long, 2.50" Diameter (Part No.E71123)
from
$24.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Bottom Cog V-Belt; 69 Inch Long, Exact Fit Premium Quality (Part No.17690)
from
$25.99
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Gates – Automotive XL« High Capacity V-Belt (Part No.9570)
from
$43.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Gates – FleetRunner« Heavy-Duty V-Belt (Part No.9485HD)
from
$31.99
Designed for the toughest applications, FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at extremely prolonged operating temperatures
- Heavy-duty construction resists cracking, wear, oil and heat
- Special compound provides unmatched stability, load carrying capacity and belt life
- Unique undercord notch pattern offers increased flexibility for smaller diameter pulleys
- Problem solver for troubled drives
- Engineered to save your fleet money and reduce downtime
- Meets RMA oil and heat resistant standards and static conductivity requirements
Gates – FleetRunner« Heavy-Duty V-Belt (Part No.9440HD)
from
$30.99
Designed for the toughest applications, FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at extremely prolonged operating temperatures
- Heavy-duty construction resists cracking, wear, oil and heat
- Special compound provides unmatched stability, load carrying capacity and belt life
- Unique undercord notch pattern offers increased flexibility for smaller diameter pulleys
- Problem solver for troubled drives
- Engineered to save your fleet money and reduce downtime
- Meets RMA oil and heat resistant standards and static conductivity requirements
Driveworks – Automotive V-Belt (Part No.50013)
from
$10.49
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Dayco – Bottom Cog V-Belt; 59 Inch Long, Exact Fit Premium Quality (Part No.15590)
from
$16.49
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Driveworks – Poly Rib Belt Serpentine Belt; 71.06 Long, 6 Rib Count (Part No.58015)
from
$5.29
Dayco engineered to conform to high mileage, worn or misaligned drives without a sacrifice in quiet, long-lasting performance. Constructed with Aramid reinforced EPDM compounds, it delivers more than OE required quality… it delivers the solution to troublesome drive problems. Dayco Poly-Rib Belts meet or exceed SAE J1459 and SAE J2432 specifications.
Product Features:
See More
Product Features:
- Aramid noise resistant fibers embedded in the rubber make this belt run quieter in worn or misaligned pulleys
- No-Noise Advanced Design EPDM rubber compound for quiet extended life
Gates – Automotive XL« High Capacity V-Belt (Part No.9520)
from
$41.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 18.63" Long, 2.25" Diameter (Part No.E71435)
from
$30.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Molded Heater Hose: EPDM, Steel, Direct Fit, 2.25" Inside Diameter (Part No.26528)
from
$99.99
Product Features:
See More
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Built-in steel spiral wire allows for medium sized curves without kinking or collapsing
- EPDM tube and Neoprene cover for extended service life
- Polyester fabric-ply reinforcement vulcanizes into shape without unnecessary strain on connections
- Resistant to heat, oil and ozone
- Performs to SAE 20R5 Type EC Class D-2 specifications
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Caution: Do not use for fuel or oil transfer applications.
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 20" Long, 2.25" Diameter (Part No.E71570)
from
$22.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.25" Diameter (Part No.B70846)
from
$19.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14" Long, 2.50" Diameter (Part No.D71009)
from
$25.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.75" Long, 2.50" Diameter (Part No.D71124)
from
$20.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Popular 1987 International 1754 Belts and Hoses Categories
1987 International 1754 Belts and Hoses
You count on your 1987 International 1754 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 56 Belts and Hoses ranging in price from $4.29 to $99.99, you’re sure to find everything you need for your 1987 International 1754.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 3 different brands like Dayco, Gates, and Driveworks. 1987 International 1754 Belts and Hoses start as low as $4.29!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 26 extensive product reviews on 1987 International 1754 Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Bottom Cog V-Belt; 58 Inch Long, Exact Fit Premium Quality with 5.0 stars and Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.25" Diameter with 4.0 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1987 International 1754 below to get started!
Top-Rated Belts and Hoses Brands For Your 1987 International 1754
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1987 International 1754 running right for years to come. In our inventory you’ll find brands like Dayco, Gates, Driveworks, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 1987 International 1754 back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Driveworks Belts and Hoses
If Driveworks are what you’re looking for, our inventory holds plenty. We stock Driveworks brand Belts and Hoses for your 1987 International 1754, and some of our most reviewed Driveworks parts include:
FAQs for 1987 International 1754 Belts and Hoses
What are the most purchased Belts and Hoses for the 1987 International 1754?
Out of 56 Belts and Hoses for the 1987 International 1754, the most popular in our inventory are:
What are the top-rated 1987 International 1754 Belts and Hoses?
Top-rated Belts and Hoses for your 1987 International 1754 based on customer reviews/ratings are:
from
$20.99
(1)
Bottom Cog V-Belt; 58 Inch Long, Exact Fit Premium Quality
“great quality & the only v belts still made without the grooves/serrated v. i prefer this brand above all others!”
from
$19.79
(1)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.25" Diameter
“Exact to oem”
