1987 GMC R2500 Performance Engines

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Product Features:

• Out-of-the-Box Bolt-On Performance
• Designed For Street/High Performance Big Blocks
• Specially Designed Oval Ports
• Increased Flow And Velocity
• Highly Efficient Semi-Open Style Chamber
• High Velocity Short Intake Ports
• Fit GM Mark IV; Gen V; and Gen VI Blocks
• Bare Head Only; Use PN[60479] for Complete

Made from high grade cork granules and a neoprene binder, these gaskets will not shrink or stick and provide excellent sealing and durability. These gaskets can be reused.

Product Features:

• Will not shrink or stick
• Provides excellent sealing and durability
• Reusable

Holley designed these throttle bodies with all relevant emission provisions and hook-ups for a true 50 state legal installation. They are engineered for a bolt-on installation on stock factory Manifolds for the applications cataloged. The one barrel throttle bodies have been assigned California Air Resources Board (C.A.R.B.) Executive Order (E.O.) number D-115-4. The two barrel throttle replacement bodies are considered to be the functional equivalent of the original equipment throttle body and, as such, are considered to be 50-State legal.

Product Features:

• Direct Replacement For OE Units
• 2 in. Throttle Bore
• 42 percent Area Increase Over Stock TBI
• Including Air Distribution Ring
• Increased Torque and Horsepower
• 50 State Legal

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Manufactured from high quality machine finished aluminum, Spectre’s Throttle Body Spacers are engineered to improve engine performance. By providing added volume to the intake manifold and directing air through a tapered internal constriction, this spacer utilizes the Venturi effect to increase the speed of air flowing into your intake manifold. Spectre has designed a number of kits to fit a wide range of specific applications. Each kit includes the necessary gaskets and hardware to bolt directly to the factory components, making installation quick and easy.

Product Features:

• Includes the necessary gaskets and hardware to bolt directly to the factory components
• Each kit is designed for the applications listed
• Manufactured from high quality machine finished aluminum
• Can be installed in less than an hour using common hand tools with no drilling or cutting required
• Simple to install

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

GSKT INTAKE

Race winning design for all types of competition. Single plane maximizes torque and horsepower. Runners feature extra material for custom porting. For performance in 3500 to 7500 RPM range. Low profile design helps minimal hood clearance. Can use 1 or 2 inch spacers to tune performance. Use PN(2999) where 1 inch spacers are not allowed. Best for standard port heads.

Product Features:

• Race Winning Design for all Types of Competition
• Single Plane Maximizes Torque and Horsepower
• Runners Feature Extra Material for Custom Porting
• For Performance in 3500 to 7500 RPM Range
• Low Profile Design Helps Minimal Hood Clearance
• Can Use 1 Or 2 in. Spacers To Tune Performance
• Use PN[2999] Where 1 in. Spacers Not Allowed
• Best for Standard Port Heads

2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Not for mileage or emissions applications. For trucks or vans use PN(2701) instead. Not for LT1 or Chevy bowtie heads. Not for 1987 and later stock aluminum heads. Available in cast or polished.

Product Features:

• 2500 to 6500 RPM High Performance Street Engines
• Single-Plane Low-Rise Intake Good for High RPM
• Ideal for Applications with Limited Hood Clearance
• For Top-End HP and Adequate Throttle Response
• Not for Mileage or Emissions Applications
• For Trucks or Vans Use PN[2701] Instead
• Not for LT1 or Chevy Bowtie Heads
• Not for 1987 and Later Stock Aluminum Heads

Choose from grade 5 hex or socket head intake bolts or grade 8 bolts with twelve point smaller-than-standard head and flange, ideal for where space is minimal. Bolts and washers are bright zinc plated for protection and appearance.

Product Features:

• Grade 8 material
• Extra thick flat washers
• Ideal for minimal space
• 12-pt head and flange
• Zinc plated for protection

Product Features:

• Case-Hardened Tubing
• Surface Hardening
• Welded Ends
• 0.3125 in. Diameter
• Use with or without Hardened Steel Guideplates

Edelbrock part #9653 Pushrods are designed for Chevy 348/409 “W” series V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precis

Product Features:

• 7.2 in. Length
• 0.312 in. Diameter
• 4130 Chromoly Steel Material
• Black Oxide Finish
• Made In The USA

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Grade 8, single bolt. Black plated finish. The washers are designed to secure the Mr. Gasket cam button pn1180, pn1181, and pn1183 or can be used as stock replacements.

Product Features:

• Specialty and drive train fastener
• Special cam bolts
• Black plated finish

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
• Not intended for use in emission controlled vehicles.

Manufactured from high-density cork and rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement and high performance street.

Product Features:

• One-piece design
• Eliminates potential leaks
• Prevents over tightening
• Prevents torque loss

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets

Product Features:

• Timing Chain Only

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

Made from silicone to withstand extreme engine oil temperatures and injection molded for a precise fit.

Product Features:

• Made from silicone
• Withstands extreme engine oil temps
• Injection molded for a precise fit

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.