from

$37.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits 1976 and up Chrysler 8.25″
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$269.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Chrysler 9.25″ rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$139.99

Dana 44 & 9.25 Chrysler TracLoc clutch kit.

Product Features:

Clutch kit
Fits Dana Spicer 44 and Chrysler 9.25″ Trac Loc positraction

from

$25.99

Product Features:

Rubber fill plug
Fits Chrysler 7.25″, 8.25″ and 9.25″

from

$389.99

Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Chrysler 9.25″
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Fits Yukon Dura Grip

from

$88.99

Six piece side gear thrust washer kit for Chrysler 8″ and 9.25″.

Product Features:

Side gear thrust washer kit
Fits Chrysler 8″ and 9.25″

from

$157.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Fits Chrysler 8.25″
Steel

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$78.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for ’76 & up Chrysler 8.25″ rear.

Product Features:

Fits 1976 and up Chrysler 8.25″
Includes carrier bearings and races

from

$527.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$141.99

Product Features:

SUPER KIT-CHRY 9.25(NON-HD)

from

$5.99

This differential cover plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential cover plug matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$9.49

Product Features:

KIT SHIM PINION

from

$198.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M88010 race
All steel construction

from

$12.99

9.25″ Chrysler rear cover gasket.

Product Features:

Cover gasket
Fits Chrysler 9.25″ rear

from

$604.99

Yukon 1541H alloy 5 lug rear axle for ’84 and older Chrysler 8.25″ van with a length of 32-5/8 inches and 27 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

27 spline
5 x 4.5″ bolt pattern
32 5/8″ long
Fits Chrysler 8.25″ in 1984 and down Dodge van

from

$10.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$7.49

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$62.99

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

Side adjuster for Chrysler 9.25″ rear

from

$16.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$194.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$209.99

USA Standard Gear open spider gear set for Chrysler 8.25″, 27 spline .

Product Features:

Spider gear kit
Fits Chrysler 8.25″ 27 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$246.99

Yukon yoke for Chrysler 9.25″ with a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 9.25″ rear
29 spline
7260 u-joint size
Inside snap ring design
2.125″ snap ring span
1.078″ cap diameter
Strap style

from

$8.99

Positraction clutch guide.

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
Compatible with Dura Grip positractions only