1987 Chevrolet Corvette Valve Cover and Cylinder Heads

Essential 1987 Chevrolet Corvette Valve Cover and Cylinder Heads

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

Cylinder Head Dowel Pins

from

$14.99
Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

Edelbrock – Sure Seat Valve Springs (Part No.5825)

Sure Seat Valve Springs

from

$147.99
The Edelbrock #5825 Replacement Sure Seat Valve Spring for Edelbrock #5085, 60759, 60909, 60719, 60739, 60999, 60899 & 79899 cylinder heads are made of highest quality spring wire and precision wound to close tolerances.

Product Features:
  • Non-Rotator Type
  • 1.460 in. Outer Diameter
  • Made In The USA
  • Single Coil Spring Type
  • Set of 16
See More

ARP Auto Racing – ARP Cylinder Head Stud Kit (Part No.234-4317)

ARP Cylinder Head Stud Kit

from

$449.99
ARP only uses premium grade 8740 alloy and a proprietary ARP2000 alloy that are rated for superior to “aircraft” quality alloy steels. Secondly, each stud is placed vertically into special racks and precisely heat-treated to 200,000 psi for the 8740 material and 220,000 psi for the ARP2000 material. This procedure ensures complete heat penetration and the results are far superior to those lesser quality studs from other manufacturers who just dump pieces in a basket and hope for the best. 

Product Features:
  • 3/8″ 12-Point, 9/16″ 12-Point, 1/8″ Allen, 3/16″ Allen Socket Size(s)
  • 8740 Chromoly
  • Black Oxide
  • 2004-Up Chevy LS1, LS6, 5.7/6.0L
  • Sold As A Kit
See More

ARP Auto Racing – ARP Cylinder Head Stud Kit (Part No.234-4301)

ARP Cylinder Head Stud Kit

from

$316.99
ARP only uses premium grade 8740 alloy and a proprietary ARP2000 alloy that are rated for superior to “aircraft” quality alloy steels. Secondly, each stud is placed vertically into special racks and precisely heat-treated to 200,000 psi for the 8740 material and 220,000 psi for the ARP2000 material. This procedure ensures complete heat penetration and the results are far superior to those lesser quality studs from other manufacturers who just dump pieces in a basket and hope for the best. 

Product Features:
  • 1/2″ 12-Point, 3/16″ Allen Socket Size(s)
  • 8740 Chromoly
  • Black Oxide
  • Small Block Chevy
  • Sold As A Kit
See More

Sealed Power – Engine Intake Valve (Part No.V-1926)

Engine Intake Valve

from

$4.99
Sealed Power parts provide innovative designs, use leading-edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Product Features:
  • Chrome plated stem
  • Hard coating added to surface for strength & aiding in lubrication
  • Note – coating added in varying thicknesses depending on application
  • Innovative design, using leading edge materials
  • Utilizes ISO & QS certified manufacturing
See More

Sealed Power – Engine Exhaust Valve (Part No.V-4345)

Engine Exhaust Valve

from

$14.99
Sealed Power« parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Product Features:
  • Chrome plated stem
  • Hard coating added to surface for strength & aiding in lubrication
  • Note – coating added in varying thicknesses depending on application
  • Innovative design, using leading edge materials
  • Utilizes ISO & QS certified manufacturing
See More

Dorman – Valve Covers: With Gasket, Direct Replacement, Aluminum, Passenger Side (Part No.264-759)

Valve Covers: With Gasket, Direct Replacement, Aluminum, Passenger Side

from

$114.99
This replacement valve cover matches the fit and function of the original equipment part that may be damaged or warped. Made from quality materials for excellent fit and superior heat resistance, this valve cover has undergone extensive testing.

Product Features:
  • Direct replacement – this valve cover matches the original equipment part for fit and function
  • Durable construction – this valve cover is made of quality materials to withstand extreme temperatures to resist leaking
  • Cost-effective solution – offers original equipment performance at competitive price
  • Quality tested – this part has undergone try-on and material testing to ensure a quality fit and reliable service
See More

Mr. Gasket – Valve Cover (Part No.9800)

Valve Cover

from

$64.19
Made of chrome plated steel. Smooth top with original equipment height and internal baffle. Features one breather/oil filler cap opening per valve cover. Hardware and gaskets sold separately.

Product Features:
  • Fits 1960-1986 Chevy 262-400 Small Block
  • OEM height, short-style covers
  • Chrome plated steel construction
  • Perimeter style bolt pattern
  • Features 1 breather/oil fill cap opening per valve cover
  • Sold as a pair
See More

ARP Auto Racing – ARP Rocker Arm Stud Kit (Part No.234-7201)

ARP Rocker Arm Stud Kit

from

$99.99
ARP rocker studs are concentric within .005″, extra-large radius base offers greater resistance to flex. Note: To be used ONLY with ARP’s patented Perma-Loc adjusters. Made of 8740 chrome moly forgings and heat-treated to 180,000 PSI. Tip ground flush for optimum adjuster seating.

Product Features:
  • 7/16″-14 Thread Size(s)
  • .700″ Thread Length
  • 8740 Chromoly
  • 1.75″ Effective Stud Length
  • Set of 16
  • .800″ Adjuster Thread Depth
  • 3/8″-24 Shank Diameter and Thread
  • 3/8″ Typical Small Block Application
  • Black Oxide
See More

ARP Auto Racing – 1.75"Oal Stud, 0.8"D Adjuster Third, 3/8"-24, 7/16"-14, 0.7"D Screw-In, Set Of 16 (Part No.134-7101)

1.75"Oal Stud, 0.8"D Adjuster Third, 3/8"-24, 7/16"-14, 0.7"D Screw-In, Set Of 16

from

$59.99
If you have ever installed a rocker stud into a cylinder head and watched it wobble as it screwed in, you knew from the beginning that the rocker geometry was going to be inconsistent all over the place. ARP rocker studs are concentric within 0.005 T.I.R. thread pitch to thread pitch. They run in straight and true. Lengths are exact designed to provide positive seating every time. An extra large radius base offers greater resistance to flex. Available in both High Performance and Pro Series models. To be used with ARP patented Perma Loc(TM) adjusters.

Product Features:
  • Made Of 8740 Chrome Moly Forgings
  • Heat Treated To 180,000 PSI
  • Excellent For Elapsed Time Bracket Racing, Limited Rule Oval Track Competition And Street Use
  • Lengths Are Exact Designed To Provide Positive Seating Every Time
  • Set of 16
  • .800″ Adjuster Thread Length
  • 3/8-24 Shank Diameter and Thread
  • 3/8″ Typical Small Block Application
See More

Felpro – CYLINDER HEAD BOLT SET (Part No.ES 72390)

CYLINDER HEAD BOLT SET

from

$36.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Avoid risk associated with re-use of T-T-Y (torque to yield) head bolts
  • Validated for fit, form and function
  • Unsurpassed quality you can trust
See More

ARP Auto Racing – For Use With 2004 And Later Gen Iii/ Ls Series Small Block, 200000Psi Tensile (Part No.134-3610)

For Use With 2004 And Later Gen Iii/ Ls Series Small Block, 200000Psi Tensile

from

$155.99
All Pro Series bolts are cold forged to ensure molecular integrity, heat treated prior to thread rolling and machining, and are rated at 200,000 PSI tensile strength. ARP Pro Series head bolt kits are application specific, designed for use with typically competition only components. These fasteners deliver superior strength and meet the ARP zero defect zero failure quality standard. Hardened and parallel ground washers are included with each kit to ensure even load distribution and accurate torque readings. All Pro Series head bolts have a reduced wrenching hex or 12 point head and wide area flange to eliminate the need for valve train removal for cylinder head retorquing and permits the use of larger diameter valve springs. Most applications have undercut short bolts that can help eliminate head gasket failures through providing more stretch to compensate for the additional compression of gaskets.

Product Features:
  • Pro Series Bolts Are Cold Forged To Ensure Molecular Integrity, Heat Treated Prior To Thread Rolling And Machining
  • Nominally Rated At 200,000 Psi Tensile Strength
  • These Fasteners Deliver Superior Strength And Meet The ARP Zero Defect Zero Failure Quality Standard
  • Bolts Have A Reduced Wrenching Hex Or 12 Point Head And Wide Area Flange To Eliminate The Need For Valve Train Removal For Cylinder Head Retorquing And Permits The Use Of Larger Diameter Valve Springs
See More

Felpro – Cylinder Head Gasket Set (Part No.HS 7733 SH-2)

Cylinder Head Gasket Set

from

$35.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Head sets contain gaskets and seals necessary for a valve grind or head reconditioning job
  • Application specific design to ensure a perfect fit and premium seal
  • Premium quality parts you can trust
  • Engineered and manufactured specifically for the repair environment
  • Unsurpassed quality you can trust
  • Contains all the parts needed to complete the repair unless otherwise noted
See More

Felpro – Cylinder Head Gasket Set (Part No.HS 26192 PT-9)

Cylinder Head Gasket Set

from

$173.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • PROPRIETARY COATING — Nonstick anti-friction coating seals small surface scratches and imperfections
  • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
  • NO RETORQUE DESIGN — Steel core helps eliminate the need for retorquing head bolts
  • STRONG AND DURABLE — Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

Sealed Power – Engine Valve Lifter (Part No.HT-2148A)

Engine Valve Lifter

from

$24.79
Sealed Power® Vintage components provide coverage for applications over 35 years old, restoring classics with like new performance. Leading edge materials, ISO & QS certified manufacturing ensures performance and longevity for treasured engine rebuilds.

Product Features:
  • Unsurpassed quality that you can trust
  • Uses leading edge materials
  • State-of-the-art manufacturing
  • Exacting tolerances
  • Meets or exceeds OEM specifications
  • New OEM riveted pin retaining design
See More

ACDelco – Active Fuel Management Valve Lifter (Part No.12680871)

Active Fuel Management Valve Lifter

from

$83.99
ACDelco GM Original Equipment Engine Valve Lifters automatically help maintain a ‘zero’ valve lash condition to help prevent valve train noise and unnecessary valve train component wear, and are GM-recommended replacements for your vehicle’s original components. These original equipment valve lifters have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:
  • Adjusts the valves on your vehicle’s engine for proper performance
  • GM-recommended replacement part for your GM vehicle’s original factory component
  • Offering the quality, reliability, and durability of GM OE
  • Manufactured to GM OE specification for fit, form, and function
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9731)

Performer Series Retainer (Qty 16)

from

$128.99
Product Features:
  • Use W/ Valve Springs Part #5762, 5795
  • Use W/ Locks Part #9612
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

Performer Series Retainer (Qty 16)

from

$95.99
Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:
  • Valve Spring Retainers for Use OE Cast Iron Heads
  • Superior Quality Heat-Treated Steel
  • Machined for Strength with Black Oxide Finish
  • Finish Ensures Rust and Corrosion Protection
See More

Sealed Power – Engine Valve Spring Retainer Keeper (Part No.VK-115)

Engine Valve Spring Retainer Keeper

from

$0.43
Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Product Features:
  • Unsurpassed quality that you can trust
  • Uses leading edge materials
  • State-of-the-art manufacturing
  • Exacting tolerances
  • Meets or exceeds OEM specifications
See More

Sealed Power – Engine Valve Spring Retainer Keeper (Part No.VK-291)

Engine Valve Spring Retainer Keeper

from

$0.65
Sealed Power« parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.
See More

Sealed Power – Push Rod (Part No.RP-3212R 100)

Push Rod

from

$9.49
Speed-Pro delivers the power you need and the value and quality that you deserve. Whether you are running at the track, chasing trophies on the strip, or just cruising down the road, count on Speed-Pro to provide the best value in HP engine components

Product Features:
  • Professional racing rods
  • 1-Piece forged end rods
  • Hardened for guide plate compatibility
  • Centerless ground to guarantee concentricity
  • Black oxide coated for corrosion protection
  • Part numbers are laser etched on each pushrod for positive ID
See More

Sealed Power – Engine Push Rod (Part No.RP-3104)

Engine Push Rod

from

$4.99
Sealed Power« parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.
See More

Mr. Gasket – Chrome Valve Cover Wing Bolts (Part No.9824)

Chrome Valve Cover Wing Bolts

from

$15.99
Chrome-plated for beauty and durability, wing bolts make valve cover removal fast & easy. They are precision-engineered and feature extra-long threads to accommodate Mr. Gasket re-usable valve cover gasket & custom valve covers.

Product Features:
  • Fits Chevy V8
  • Standard Y Top 1/4 In-20 X 5/8 in L
  • Chrome Plated Steel
  • Overall Length: 4.64″
  • Installed Length: 4.00″
  • Pack of 4
See More

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5799G)

Ultra Seal: Head Gasket

from

$68.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.130 inch, Compressed thickness 0.055 inch

Product Features:
  • Five layer (graphite core/perforated steel outer layers) composite construction
  • Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
  • Provides excellent stability, compressibility and high temperature endurance
  • Coated with high temperature silicone to ensure sealing of engine fluids
  • Will not brinell (indent) aluminum cylinder heads
  • For high performance street, drag race and oval track use
  • Compatible w/High Octane Fuel
  • Compatible With Exotic Fuel
See More

Felpro – Cylinder Head Gasket: Composite, Without Head Bolts (Part No.9284 PT)

Cylinder Head Gasket: Composite, Without Head Bolts

from

$26.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Application specific design to ensure a perfect fit
  • Requires no retorquing of the head bolts
  • Unsurpassed quality you can trust
  • Unsurpassed quality you can trust
See More

Edelbrock – RPM Big-Block Chevy Oval Port Cylinder Head Hydraulic Flat Tappet Cam (Part No.60439)

RPM Big-Block Chevy Oval Port Cylinder Head Hydraulic Flat Tappet Cam

from

$1156.99
The Edelbrock #60439 Performer RPM High-Compression O-Port cylinder head is designed for Big-Block Chevy applications. The Edelbrock #60439 Performer RPM head is perfect for street performance, daily drivers, street rods and muscle cars where seat-of-the-

Product Features:
  • Complete Single High Compression 454-0
  • 100cc Combustion Chamber Volume
  • 290cc Intake/110cc Exhaust Runner Volume
  • 2.19 in. Intake/1.88 in. Exhaust Valve Diameter
  • 0.562 in. Deck Thickness
See More

Spartan – Engine Cylinder Head; Chev 350 64-85 Cyl Head (Part No.2C11)

Engine Cylinder Head; Chev 350 64-85 Cyl Head

from

$341.99
Remanufactured Cylinder Heads are complete rebuild & include new valve stem seals, soft plugs & verified camshafts. All threads are checked and repaired if necessary. Cylinder Heads are packaged in heavy plastic to protect the unit.

Product Features:
  • All cylinder heads are both vacuum and pressure tested to verify valve seating, & integrity of water passages.
  • All cylinder heads are packaged in environmentally safe and recyclable containers that are the perfect size for returning your original core
  • All threads and machined surfaces are and repaired with technology that exceeds the original metal
  • Non-sealing iron surfaces painted to prevent oxidization
See More

Spartan – Engine Cylinder Head; Chev LS 01-15 Head (Part No.2CTU)

Engine Cylinder Head; Chev LS 01-15 Head

from

$579.99
Remanufactured Cylinder Heads are complete rebuild & include new valve stem seals, soft plugs & verified camshafts. All threads are checked and repaired if necessary. Cylinder Heads are packaged in heavy plastic to protect the unit.

Product Features:
  • All cylinder heads are both vacuum and pressure tested to verify valve seating, & integrity of water passages.
  • All cylinder heads are packaged in environmentally safe and recyclable containers that are the perfect size for returning your original core
  • All threads and machined surfaces are and repaired with technology that exceeds the original metal
  • Non-sealing iron surfaces painted to prevent oxidization
See More

1987 Chevrolet Corvette Valve Cover and Cylinder Heads

Maybe you’re in the middle of a full rebuild of that 1987 Chevrolet Corvette. Maybe you just need a couple of Valve Cover and Cylinder Heads. Either way, Advance Auto Parts has 35 different Valve Cover and Cylinder Heads in our inventory ranging from $0.43 to $1,192.99. That means you can find the exact parts or products you need to keep that 1987 Chevrolet Corvette running smoothly.

Valve Cover and Cylinder Heads are only as good as their brand. We stock 6 different brands to make sure you have plenty of trusted parts to choose from for your 1987 Chevrolet Corvette. Sealed Power, Felpro, and Mr. Gasket are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Valve Cover and Cylinder Heads for your 1987 Chevrolet Corvette, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 98 reviews in this category, some of the top rated parts include Engine Push Rod with 5.0 stars and Engine Valve Spring Retainer Keeper with 5.0 stars.

So if you’re in the market for aftermarket Valve Cover and Cylinder Heads to keep your 1987 Chevrolet Corvette rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Valve Cover and Cylinder Heads Brands To Make Your 1987 Chevrolet Corvette Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1987 Chevrolet Corvette demands trusted brand parts and products to keep it running. Many trusted brands of Valve Cover and Cylinder Heads make up Advance Auto Parts’ inventory, and all are ready to help make your Corvette the best it can be. Be sure to browse some of our top Valve Cover and Cylinder Heads brands and parts.

FAQs for 1987 Chevrolet Corvette Valve Cover and Cylinder Heads

What are the most purchased Valve Cover and Cylinder Heads for the 1987 Chevrolet Corvette?

Out of 35 Valve Cover and Cylinder Heads for the 1987 Chevrolet Corvette, the most popular in our inventory are:
Engine Valve Lifter
from $12.99
(30)
Engine Valve Lifter
Engine Valve Lifters
Engine Valve Lifter
from $24.79
This product is not rated
Engine Valve Lifter
Engine Valve Lifters
Chrome Valve Cover Wing Bolts
from $15.99
(9)
Chrome Valve Cover Wing Bolts
Valve Cover Bolts

What are the top-rated 1987 Chevrolet Corvette Valve Cover and Cylinder Heads?

Top-rated Valve Cover and Cylinder Heads for your 1987 Chevrolet Corvette based on customer reviews/ratings are:
Engine Push Rod
from $2.99
(2)
Engine Push Rod
“1986-1990 GM 4.3L Understand this headline or you’ll need 12 of these beauties. Not always covered in manuals. 48 hours and I had these in hand with f”
Engine Valve Spring Retainer Keeper
from $0.43
(2)
Engine Valve Spring Retainer Keeper
“I would purchase again”
Engine Valve Spring
from $2.49
(1)
Engine Valve Spring
“Finished off the valve job on my old GM 5.7. Great price.”