Name: Lock Right Locker
Brand: Powertrax
SKU: 1921-LR
Price: 368.99 USD

from

$368.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$354.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits GM 7.5″ and 7.6″
7.50″ ring gear diameter
27 spline pinion
10 ring gear bolts
3.42 ratio
Thick gear for 3.23 and down carrier

from

$52.99

Product Features:

Crush sleeve eliminator kit for GM 7.5″, 7.625″ and 8.2″

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$184.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$187.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1982-1999 GM 7.5″ and 7.625″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$2.79

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$11.99

7.5 GM cover gasket.

Product Features:

Cover gasket
Fits GM 7.5″ and 7.625″

from

$3.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$202.99

14 plate DURAGRIP COMPOSITE clutches, GM 7.5.

Product Features:

Clutch kit
Fits GM 7.5″ and 7.625″ with Dura Grip positraction
Steel clutches

from

$49.99

Product Features:

MINI INSTALL KIT GM 7.5

from

$202.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits 1982-1999 GM 7.5″ and 7.625″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$279.99

Yukon spider gear set for GM 7.5″ & 7.625″ Dura Grip posi, 26 spline. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY.

Product Features:

Spider gear kit
Fits GM gm 7.5″ with 26 spline Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$8.99

7.5 & 7.625 Standard Open Pinion gear Thrust Washer.

Product Features:

Pinion gear thrust washer for GM 7.5″ and 7.625″
Fits standard open differentials only

from

$10.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$195.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$101.99

Product Features:

MINI SPOOL GM 7 1/2″ 28 SPLINE

from

$166.99

Product Features:

Positraction spring kit
Fits GM 7.5″ and 7.625″ Dura Grip
Includes preload plates

from

$61.99

Product Features:

Fits GM 7.5″ and 7.625″
Steel

from

$222.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits 1982-1999 GM 7.5″ and 7.625″
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve , marking compound and brush.

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$9.99

Pinion nut for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.0″, 8.25″, 8.5″, 8.6″, 9.25″ IFS, 9.5″ & Oldsmobile Dropouts. 1 1/4″ socket, 7/8″ x 14 thread.

Product Features:

Pinion nut for GM 7.2″, 7.5″, 7.625″, 8.0″, 8.25″ IFS, 8.5″, 8.6″, 9.25″ IFS and 9.5″
7/8″ x 14 thread
1 1/4″ socket

from

$438.99

7.2IFS GM Standard Open loaded case 3.23 & up.

Product Features:

Standard open carrier case
Includes spider gears
Fits GM 7.2″ IFS
3.23 and up ratios only

from

$6.99

Ring gear bolt for GM 7.5″, 7.6″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ & 8.6″ IRS. 7/16″ x 20.

Product Features:

Ring gear bolt for GM 7.5″, 7.625″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ and 8.6″ IRS
7/16″ x 20

from

$21.99

Product Features:

Pinion depth shims for GM 7.5″, 7.625″, 7.6 IFS, 7.6 IRS, 7.75″, 8.2″, 1955-1964 passenger car and 12 bolt car and truck

from

$17.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

Manufactured from high quality elastomer compounds for durability and ride performance
Assembled with proper precompression for ultimate in performance and feel
High level bonding adhesive is used for durability
Elastomer compounds do not utilize any reground rubber fillers