from

$301.99

Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Chrysler 8.25″ open differntial with 27 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$389.99

Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Chrysler 9.25″
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Fits Yukon Dura Grip

from

$173.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Chrysler 9.25″ rear differential. This kit contains carrier bearings and races.

Product Features:

Fits Chrysler 9.25″ rear
Includes carrier bearings and races

from

$261.99

Product Features:

Standard open carrier case
Fits 2009 and down Chrysler 9.25″ rear
Does not include spider gears

from

$8.79

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$31.99

Product Features:

MINI-INSTLTN KIT-CHRYSLER 7 1/4″

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$12.99

8.25″ Chrysler cover gasket.

Product Features:

Cover gasket
Fits Chrysler 8.25″

from

$159.99

Yukon yoke for GM 12 bolt car & truck, 1330 u/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 1976 and up Chrysler 8.25″
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$5.99

This differential cover plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential cover plug matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$674.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon has an updated, proprietary, design that provides longer life and higher durability than the competition. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. We reccomend an OEM gear for van applications. This gear set is for ’09 and older applications only.

Product Features:

Fits 2010 and down Chrysler 9.25″ rear
9.25″ ring gear diameter
29 spline pinion
12 ring gear bolts
3.55 ratio

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$17.99

Yukon 1541H alloy right hand rear axle for Model 35 (drum brakes) with a 54 tooth, 2.7″ ABS ring. axle has a length of 29-1/4″ inches and 27 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H allo

Product Features:

Pinion depth shims for AMC Model 35 and Chrysler 7.25″

from

$159.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1976 and up Chrysler 8.25″
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$5.99

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$10.99

Pinion nut for Chrysler 7.25″, 8.0″ IFS, 8.25″, 8.75″ fine spline, 9.25″ front & rear, 7/16″ x 14.

Product Features:

Pinion nut for Chrysler 8.0″ IFS, 8.25″, 8.75″ with 29 spline pinion and 9.25″ rear
7/8″ x 14 thread

from

$13.99

Pinion seal for 8.75″ Chrysler or for 9.25″ Chrysler with 41 or 89 housing.Yukon Mighty seal.

Product Features:

Pinion seal
Fits Chrysler 8.75″ with ’41’ and ’89’ case housings and 2000 and down Chrysler 9.25″

from

$159.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Fits Chrysler 8.25″
Steel

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$12.99

9.25″ pinion gear thrust washer.

Product Features:

Pinion gear thrust washer for Chrysler 9.25″ rear

from

$279.99

Yukon yoke for Chrysler 7.25″ and 8.25″ with a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 7.25″ and 8.25″
27 spline
7260 u-joint size
Inside snap ring design
2.125″ snap ring span
1.078″ cap diameter
Strap style

from

$829.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits Chrysler 9.25″ rear
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$125.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features: