Name: Spartan Spring & Pin Kit, Fits Smaller Designs
Brand: USA Standard Gear
SKU: 17011
Price: 26.99 USD

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$4.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$8.51

Axle Seal

from

$22.99

Product Features:

Ring gear bolt and nut kit
Fits Toyota Landcruiser
Includes one bolt and one nut

from

$603.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 9.5″ Landcruiser with 30 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$126.99

Bearing race driver front Toyota 7.5″, 8″, Landcruiser, and the Suzuki Samurai. No return. (TOY30306).

Product Features:

Bearing race driver
Fits 30306 race
All steel construction

from

$30.99

Preload shim kit for Toyota Landcruiser. Also compatible with Toyota 8″ 4 cylinder & V6 with a solid spacer.

Product Features:

Preload shim kit
Fits 9.5″ Toyota Landcruiser

from

$274.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits standard rotation Toyota Landcruiser
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$51.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Matched cup and cone components ensures consistent quality and outstanding performance
Industry leading coverage
Professional technicians know they can depend on National

from

$36.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Compatible with most oils and EP lubricants at higher operating temperatures
High resistance to oxidation and ozone and has low swell in hydrocarbon fluids
Temperature range: -20°F to 300°F; -29°C to 149°C
National® oil seals are recognized worldwide for their quality and reliable performance for every type of repair.

from

$103.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. No side shims.

Product Features:

Fits standard rotation Toyota Landcruiser
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$192.99

Ring gear bolt kit for Toyota Landcruiser.

Product Features:

Fits standard rotation Toyota Landcruiser
Included are ring gear bolts and nuts

from

$1099.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts.

Product Features:

Fits Toyota 9.5″ Landcruiser with 30 spline axles
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$12.99

Valvoline ATF for MERCON®V Applications is a high-quality transmission fluid meeting and exceeding the requirements of the Ford Mercon V specification which covers most Ford passenger cars and light-duty trucks (except those specifying MERCON®SP, MERCON®LV or Type F fluids), including Lincoln and Mercury, as well as most pre-2006 GM vehicles and many imports. Recommended for use in the following applications: MERCON®V, MERCON®, DEXRON®-III, DEXRON®-II, Caterpillar TO-2, Allison C-4. Other applications include Power steering fluid where a DEXRON® or MERCON® fluid is recommended. Suitable to use in Nissan Matic D, Matic J and Matic K.

Product Features:

Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$169.99

Yukon yoke for ’78 to ’84 Toyota Lancruiser with 27 spline pinion. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 1978-1984 Toyota Landcruiser
27 spline

from

$447.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Toyota 9.5″ Landcruiser
9.50″ ring gear diameter
27 spline pinion
10 ring gear bolts
5.29 ratio

from

$31.99

Product Features:

Pinion gear thrust washer
Fits Toyota Landcrusier

from

$34.99

Toyota Landcruiser crush sleeve. Approx 2.220″ long.

Product Features:

Crush sleeve
Fits Toyota Landcruiser
2.220″ tall

from

$32.99

Product Features:

Cross pin shaft
Fits Toyota Landcruiser

from

$8.99

Toyota Landcruiser ring gear nut for ring gear bolt.

Product Features:

Ring gear nut
Fits Toyota Landcruiser

from

$5.99

Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landrcuiser (fine spline pinion) & T100/Tacoma with factory locker. 30mm socket, M20 x 1.5 thread.

Product Features:

Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landcruiser with 30 spline pinion and Tacoma/T100 with factory locker
20mm x 1.5 thread
30mm socket

from

$15.99

Toyota Landcruiser pinion nut, coarse spline, LARGE. 22mm x 1.5mm.

Product Features:

Pinion nut
Fits Toyota Landcruiser with 10 spline pinion

from

$436.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits 1991 and up Toyota Landcruiser
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

from

$364.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits 1990 and down Toyota Landcruiser
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

from

$359.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

Fits 1990 and down Toyota Landcruiser
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and silicone.

from

$121.99

Product Features:

TOYOTA LAND CRUISER 1965-UP TAPER PINION

1985 Toyota Land Cruiser Differentials

More 1985 Toyota Land Cruiser Differentials

Essential 1985 Toyota Land Cruiser Differentials

USA Standard Gear – Spartan Spring & Pin Kit, Fits Smaller Designs (Part No.17011)

Driveworks – Taper Bearing Cup (Part No.S-JLM-104910)

Corteco – Axle Seal (Part No.K4021473844CFW)

Yukon Gear – Toyota Landcruiser Ring Gear Bolt & Nut Kit (Part No.33200)

USA Standard Gear – Spartan Locker For Toyota 95" Landcruiser With 30 Spline Axles, Includes Heavy-Duty Cross Pin Shaft (Part No.17033)

Yukon Gear – Outer Oil Slinger (Part No.33025)

Yukon Gear – Bearing Race Driver (Part No.56005)

Yukon Gear – Solid Preload Kit For Toyota Landcruiser (Part No.55065)

Yukon Gear – Pinion Install Kit For Toyota Landcruiser Differential (Part No.13091)

National – Bearings (Part No.30306)

National – Oil Seal (Part No.710931)

Yukon Gear – Minor Install Kit For Toyota Landcruiser Differential (Part No.12074)

Yukon Gear – The Carrier Bearing Puller (Part No.56034)

Yukon Gear – Ring Gear Bolt Kit For Toyota Landcruiser (Part No.12075)

Yukon Gear – Grizzly Locker For Toyota Landcruiser, 30 Spline (Part No.28032)

Valvoline – ATF for Mercon®V Applications Conventional, 1 Quart (Part No.822345)

Yukon Gear – Yoke For ’78 To ’84 Toyota Lancruiser With 27 Spline Pinion (Part No.41110)

USA Standard Gear – Ring & Pinion Gear Set For Toyota Landcruiser In A 5.29 Ratio (Part No.36259)

Yukon Gear – Landcruiser Standard Open Pinion Gear Thrust Washer (Part No.33394)

Yukon Gear – Toyota Landcruiser Crush Sleeve (Part No.33114)

Yukon Gear – Landcruiser Standard Open Cross Pin Shaft (Part No.33419)

Yukon Gear – Toyota Landcruiser Ring Gear Nut For Ring Gear Bolt (Part No.33062)

Yukon Gear – Pinion Nut (Part No.33156)

Yukon Gear – Toyota Landcruiser Pinion Nut, Coarse Spline (Part No.33158)

Yukon Gear – Bearing Install Kit For ’91 And Newer Toyota Landcruiser Differential (Part No.11091)

Yukon Gear – Bearing Install Kit For ’90 & Older Toyota Landcruiser Differential (Part No.11090)

Yukon Gear – Master Overhaul Kit For ’90 And Older Toyota Landcruiser Differential (Part No.14121)

Motive Gear – Differential Bearing Kit – Koyo (Part No.R11RLC)

Popular 1985 Toyota Land Cruiser Differentials Categories

1985 Toyota Land Cruiser Differentials

Differentials Brands To Make Your 1985 Toyota Land Cruiser Last

Popular Valvoline Differentials

FAQs for 1985 Toyota Land Cruiser Differentials

What are the most purchased Differentials for the 1985 Toyota Land Cruiser?

What are the top-rated 1985 Toyota Land Cruiser Differentials?

More Popular Parts for All Makes