1985 Ford Bronco Performance Engines

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

HYDRAULIC – Magnum: Broad power. 2500+ stall, low gears, 9.5:1 compression and headers. Rough idle. OR Marine: Off shore type boat. Strong performance, rough idle.

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

This B&M Holeshot 2400 fits 1966-91 Ford C6 transmissions with 1.848-inch crank pilot and a 11.4-inch bolt circle. The Holeshot converters are an excellent choice for vehicles with engine modifications, particularly big cams that tend to reduce low end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product.

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

“Edelbrock part No: 7328 head gasket is intended for Ford 351 Cleveland engines. This gasket comes as a set and has a 4.080″” bore size, .038″” compressed thickness and 8.1 cc volume.”

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

The Edelbrock No. 5028 E-Series Cylinder heads are designed for Small-Block Ford applications. The Edelbrock E-Series cylinder heads are a step up in affordable performance from our E-Street line. They feature larger runners for increased airflow, revised exhaust ports and larger diameter springs for higher lift camshafts, making them ideal for a spec series racer and larger displacement engines. The Edelbrock No. 5028 E-Street Cylinder heads also have as-cast ports and maintain the stock exhaust port location, making them compatible with OEM headers and hardware.

“These Magnum Roller Rocker Arms for Ford V8 289-351W (Rail Type) 1968-89 applications are the ultimate street rocker. With a 3/8″” stud diameter and 1.6 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed from 8620 chromemoly steel, which is a superior material that will not flex and assures maximum lift. Their roller tip reduces friction, while stiff design and superior ratio accuracy yield more effective valve lift. With a 15 to 30 horsepower increase over other rocker arms, Magnum Roller Rockers are perfect for performance applications with less than 350 lbs. open spring pressure. Don’t accept inferior products or cheap knock-offs, look for the COMP Cams logo stamped into the underside of every Magnum Rocker.”

It’s easy to overlook the small details. For engine builders focused on the larger components like camshafts, cylinder heads and pistons, small parts are often forgotten until the final stages of engine assembly. COMP Cams Engine Finishing Kits include those often missing parts like woodruff keys, cylinder head alignment dowels, cam bolts, cam eccentrics and timing cover and oil pump dowel pins that are so crucial to properly assembling your engine.

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It is a direct replacement for a factory one-piece rubber main seal. It’s also injection molded for a precise fit.

Competition Cams Magnum Double Row Timing Set for ’65-’88 Ford 255, 289, 302 and Boss 302, 2120.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Edelbrock part No: 7814 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

Edelbrock Valve Spring Retainers are made of superior quality steel and are machined and heat treated for maximum strength. They feature a black oxide finish to prevent rust and corrosion

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

3) For off-highway use, non-EGR 4V system with an Edelbrock #8714 4V spacer.

Edelbrock Performer 400 Intake Manifold for 1971-82 Ford 351/M400, 2171.

“Edelbrock part #2921 Victor Jr. 302 intake manifold is designed for Ford 289-302 competition engines using modified stock cast iron or aftermarket Windsor-style cylinder heads such as Edelbrock #60259 and #77169 or equivalent. This intake manifold has bosses for rear water crossover. Port exit size at cylinder head is 1.08″” x 1.90″” with extra material to accommodate a 1.18″” x 2.10″” opening. This Victor Jr. is a single-plane, high-rise intake designed for maximum race-winning power at higher engine speeds.”

“Edelbrock part No: 9655 Pushrods are designed for small-block Ford 289-302 V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise formed wedged ends for a high quality fit with the cup seats. A black oxide finish is added for corrosion resistance. Pushrod Specifications: – For hydraulic rollers, 5.0L with stud mount. Refer to lifter kit No: 97453 – Outside Diameter: 5/16″” – Length: 6.400″””

“Competition Cams High Energy 10.136″” Long, 5/16″” Diameter Pushrod Set of 12, 7866-12. ”

“Competition Cams High Energy 6.248″” Long, 5/16″” Diameter Pushrod Set, 7826-16. ”