from

$48.99

12P solid crush sleeve replacement spacer, pinion preload.

Product Features:

Crush sleeve eliminator kit for GM 12 bolt passenger car

from

$75.99

The Mr. Gasket chrome plated rear end cover is made from heavy-gauge steel, and comes complete with bolts and gaskets.

Product Features:

Chrome plated steel for looks
Includes bolts and gasket

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$6.99

Ring gear bolt for GM 12 bolt car & truck, 8.2″, 8.2″ for Buick/Olds/Pontiac, 63-79 Corvette & 55-62 GM Car & Truck. 3/8″ x 24.

Product Features:

Ring gear bolt for GM 12 bolt passenger car and truck, 1955-1964 passenger car and truck, GM 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and 1963-1979 Corvette
3/8″ x 24 thread

from

$201.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1981 and down GM 7.5″
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$4.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$175.99

Mini Spool for 8.2″ GM with 28 spline axles. Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.2″
Provides 100% traction to both wheels at all times
Installs into standard open carrier case

from

$115.99

Product Features:

INTERNAL KT GM 7.5 26 SPL

from

$57.99

Cross pin shaft for 7.5″, 7.625″, and 8″ GM.

Product Features:

Cross pin shaft for GM 7.5″, 7.625″ and 8.0″
Fits standard open differentials only

from

$12.79

Product Features:

High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks
Long-life friction modifiers and premium base oils help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
Enhanced cleaning additives help reduce varnish formation and keep the transmission running properly longer
Engineered with a unique blend of viscosity modifiers and base oils to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$121.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.6″, 12 bolt car and 12 bolt truck differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 12 bolt passenger car and truck and 8.6″
Includes carrier bearings and races and “super” carrier shim kit

from

$2.79

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$373.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
14 piece kit
Composite clutches

from

$53.99

Positraction cross pin bolt for for 8.2″ GM CI ‘Vette.

Product Features:

Cross pin bolt for GM 8.2″ and 1963-1979 Corvette
For OEM positraction applications only

from

$839.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits GM 12 bolt passenger car with 30 spline axles
4.10 and up ratio only
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA
30 spline

from

$189.99

USA Standard axle shaft for Monte Carlo & El Camino. 28 7/16″, 26 spline.

Product Features:

Fits GM 7.5″ in Monte Carlo and El Camino
26 spline
28 7/16″ long

from

$7.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$19.79

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$39.49

RngPnnInstlKt

from

$64.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$10.99

Product Features:

Clutch guide
Fits GM 7.5″ and 7.625″ Dura Grip

from

$154.99

Yukon yoke for GM 7.5″ and 7.625″ (mech 3R) in a triple lip design. 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring. This yoke uses inside clips. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 7.5″ and 7.625″
27 spline
Mechanics 3R u-joint size
2.556″ snap ring span
1.125″ cap diameter
Inside snap ring design
Strap style

from

$274.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits GM 8.5″ and 8.6″
8.50″ ring gear diameter
30 spline pinion
10 ring gear bolts
3.73 ratio

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$10.99

8.2″ & 8.5″ rear cover gasket.

Product Features:

Cover gasket
Fits GM 8.2″, 8.5″ and 8.6″

from

$336.99

Yukon positraction internals (0.795″ diameter) for 8.5″ GM with 28 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects. This kit is compatible with Yukon Dura Grip or Eaton positractions. It will not fit a factory Gov-Loc positraction.

Product Features:

Spider gear kit
Fits GM 8.5″ with 28 spline Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.